Honeywell T775M Betriebsanleitung
To program the controller, perform the following procedures in the order listed:
Fig. 1
Press the MENU button, then select PROGRAM and press the button to view the
program menu.
Fig. 1 shows the Program menu for controller.
Fig. 2
1. From the menu, use the and buttons to highlight MOD 1.
2. Press the button to select MOD 1 to view the parameters. Fig. 2 shows
RELAY 1. In MOD 1, THROT RNG replaces DIFFERNTL.
!"#
Fig. Program – Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 55°F.
4. Press the button to accept the setpoint temperature and display the next
option.
!"$%&'!"$&"$
Fig. Program – Throttling Range
1. From the menu, use the and buttons to highlight THROT RNG.
2. Press the button to display the throttling range value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
( " &
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor B.
4. Press the button to accept the highlighted sensor and display the next option.
)%*'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select COOL.
4. Press the button to accept the highlighted selection and display the next
option.
+
Press the button to accept the highlighted selection EXIT. This will display the main
Program Menu screen (Fig. 1)
Fig. 1
("+,#-
1. From the menu, use the and buttons to highlight MOD 2.
2. Press the button to select MOD 2 to view the parameters.
( !"#
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 55°F.
4. Press the button to accept the setpoint temperature and display the next
option.
( !"$%&'!"$&"$
Fig. Program – Throttling Range
1. From the menu, use the and buttons to highlight THROT RNG.
2. Press the button to display the throttling range value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
(( " &
Fig. Program – Sensor
5. From the menu, use the and buttons to highlight SENSOR.
6. Press the button to display the sensor selections.
7. Use the and buttons to select Sensor A or B.
Select sensor A.
8. Press the button to accept the highlighted sensor and display the next option.
()%*'
Fig. Program Heat/Cool
5. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
6. Press the button to display the heat and cool selections.
7. Use the and buttons to select Heat or Cool.
Select HEAT.
8. Press the button to accept the highlighted selection and display the next
option.
_____________________________________________________________________
(+
Press the button to accept the highlighted selection EXIT. This will display the main
Program Menu screen (Fig. 1)
Fig. 1
)"+,&'.-
1. From the menu, use the and buttons to highlight RELAY 1.
Fig. 2
2. Press the button to select RELAY 1 to view the parameters.
) !"&'.
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT (Fig. 2).
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 100°F.
4. Press the button to accept the setpoint temperature and display the next
option.
_____________________________________________________________________
)#!&"!' !"$
Fig. Program – Differential
1. From the menu, use the and buttons to highlight DIFFERNTL.
2. Press the button to display the differential value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
)( " &
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor A.
4. Press the button to accept the highlighted sensor and display the next option.
))%*'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select HEAT.
4. Press the button to accept the highlighted selection and display the next
option.
+
Fig. Program – Exit
Press the HOME button to leave programming mode and return to the home screen.
This completes the programming procedure.
Inhaltsverzeichnis
Andere Honeywell Controller Handbücher
Honeywell
Honeywell Excel 50 Bedienungsanleitung
Honeywell
Honeywell 40014 Bedienungsanleitung
Honeywell
Honeywell Lyric LCP300-LC Produktinformationsblatt
Honeywell
Honeywell CENTRA LINE EAGLEHAWK NX Installations- und Betriebshandbuch
Honeywell
Honeywell HCE 40 Programmierhandbuch
Honeywell
Honeywell ML6984 Bedienungsanleitung
Honeywell
Honeywell SSW2-1M Bedienungsanleitung
Honeywell
Honeywell N20 Series Bedienungsanleitung
Honeywell
Honeywell WEBsAX Series Leitfaden
Honeywell
Honeywell NPB-2X-RS485 Bedienungsanleitung
Honeywell
Honeywell Air Alert 96d Bedienungsanleitung
Honeywell
Honeywell ML6421 Bedienungsanleitung
Honeywell
Honeywell SUPER TRADELINE S8610U Bedienungsanleitung
Honeywell
Honeywell SUPER TRADELINE S8610U Bedienungsanleitung
Honeywell
Honeywell HON 5020 Bedienungsanleitung
Honeywell
Honeywell Touchpoint Plus Bedienungsanleitung
Honeywell
Honeywell R7515C MacroCel Bedienungsanleitung
Honeywell
Honeywell SHC Series Bedienungsanleitung
Honeywell
Honeywell ML7999C Bedienungsanleitung
Honeywell
Honeywell ICON 100 SERIES Bedienungsanleitung
