Honeywell VBN2 Bedienungsanleitung

INSTALLATION INSTRUCTIONS

62-0197-04

VBN2, VBN3

Control Ball Valve/Actuator

Assemblies

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a

hazardous condition.

2. Check ratings given in the product data literature

and on the product to ensure the product is suit-

able for your application.

3. Installer must be a trained, experienced, licensed

service technician.

4. After installation is complete, check out product

operation as provided in these instructions.

Preparation

CAUTION

Equipment Damage Hazard.

Foreign particles like dirt and metal chips can

damage the ball seals.

Clean upstream lines prior to installation.

CAUTION

Equipment Damage Hazard.

Improper chemicals can damage the valve.

Use neither aerosol products nor petroleum-

based lubricants.

1. Clean the lines upstream of particles larger than

1/16 in. diameter. Open valves fully. Flush entire

hydronic system of contaminants (welding slag,

solder, scale, metal chips, etc.) and chemically

treat water according to local conditions prior to

operation.

2. Proceed with installation once the system specifics

(expansion/contraction of the system and its

medium as well as operating pressures) are within

tolerances.

3. Eliminate air from system.

4. Two-way valves are marked to show flow direction.

IMPORTANT

Flow arrows must point in the direction of the

flow for proper operation.

NOTE: For three-way valve mounting, see Fig. 3

through 5.

5. Stem rotation:

a. For two-way valves:

(1) Clockwise to close.

(2) Counterclockwise to open.

b. For three-way valves:

(1) Clockwise to increase B to AB flow.

(2) Counterclockwise to increase A to AB flow.

6. Valve must be mounted with the actuator/bracket

above the valve body. Do not install the valve with

the stem below horizontal or upside down. (See

Fig. 1 and 2.)

Fig. 1. Vertical valve installation.

Fig. 2. Acceptable valve angle from vertical.

M29518

85 85

M29519A

VBN2, VBN3 CONTROL BALL VALVE/ACTUATOR ASSEMBLIES

62-0197—04 2

Fig. 3. Three-way ball valve flow orientation

(not to scale).

Fig. 4. Reset mixing control for discharge hot water.

Fig. 5. Three-way mixing valve operation

with coil bypass.

Mechanical Installation

The valveshave female NPT pipe fittings and should be

sealed with an approved pipe sealant or tape. Take care

not to use excess pipe dope to avoid interfering with

operation of ball. Torque should not exceed 75 ft-lb.

See Fig. 8 and 9 for valve dimensions. Refer to actuator

literature for actuator dimensions.

Mounting Plate Adjustment

The Actuator Mounting Plate can be rotated to a different

position for installation in confined spaces. This is

accomplished as follows:

1. Remove the handle from the shaft and set it aside.

2. Remove the two screws that hold the stem

assembly to the mounting plate and set them aside.

3. Remove and set aside the stem assembly.

4. Remove and set aside the two screws that attach

the mounting plate to the valve.

5. ENSURE VALVE IS ISOLATED AND DEPRES-

SURIZED BEFORE PROCEEDING. Remove yel-

low pressure plate marked “HIGH PRESSURE”

from valve bonnet, rotate 90° or 180°, and re-install

screws using same holes in pressure plate and the

appropriate pair of tapped holes in the valve bonnet.

NOTE: Take note of the screw hole positions on

the valve. They limit the mounting plate

positions.

6. Rotate mounting plate around valve top to the

desired position.

IMPORTANT

Do not rotate the valve stem while the hold-down

ring is removed. This can change the common

port from AB to A.

7. Lower ring down to valve body and engage it in the

new position relative to the mounting plate.

8. Tighten screws to valve body securing the mounting

plate.

9. Reattach the stem assembly to the mounting plate.

10. If desired, replace the handle on the shaft.

NOTE: See Fig. 6 for valve exploded view.

IMPORTANT

After adjusting a three-way valve mounting plate,

take note whether the AB port or the A port is the

common port.

Electrical Installation

1. If necessary, remove actuator wiring cover.

2. Wire the actuator according to the appropriate

diagram provided with actuator or job specifica-

tions. For detailed actuator information, see Honey-

well literature:

— 62-0274—MS7505/MS8105 Spring Return

Actuator Installation Instructions

— 63-2632—MN6105 Floating Actuator

Product Data

— 63-2633—MN7505 Modulating Actuator

Product Data

— 63-2209—ML6161/ML6164/ML7161/ML7164

Non-spring return direct Coupled Actuators

Product Data

3. If applicable, position reverse/direct acting switch

for desired operation.

4. Replace cover.

M13737

SUPPLY

RETURN

AB PORT A PORT

B PORT

COIL

SUPPLY

RETURN

AB PORT A PORT

B PORT

COIL

MIXINGDIVERTING

A AB

M29517

BOILER

PUMP

VBN3

AB A

M19523

HEATING COIL

FULL

HEAT

5 GPM

2.5 GPM

5 GPM

AB A

PROPORTIONED

HEAT

2.5 GPM

SU P P L Y

MAIN

RETURN

MAIN

5 GPM

VB3

HEAT

NO FLOW

THROUGH COIL

VBN2, VBN3 CONTROL BALL VALVE/ACTUATOR ASSEMBLIES

3 62-0197—04

Fig. 6. Valve assembly exploded view.

OPERATION AND CHECKOUT

Once both the mechanical and electrical installations are

complete:

1. Cycle the actuator to verify that the direction of rota-

tion suits the control sequence.

2. If the rotation direction is incorrect:

a. For 2-position control actuators: Remount actu-

ator on the bracket.

b. For floating control actuators: Reverse two con-

trol signal wires (CW/CCW).

c. For analog control actuators either:

(1) Reposition reverse/direct acting switch, or

(2) Remount actuator on the bracket.

3. If the control scheme requires fail-safe operation,

ensure that, upon removal of power, the valve

rotates to the desired position.

4. Spring return actuators are factory-configured for

A-port normally-closed fail-safe operation. To

change this to normally-open, remove and reinstall

the actuator in the opposite orientation as follows:

(a) Loosen the shaft coupling bolt using a 10

mm wrench.

(b) Loosen all other mounting bolts connect-

ing the actuator to the mounting bracket,

and set aside.

shaft.

(d) Move the actuator shaft coupling to the

opposite side of the actuator, as displayed

in Figure 7.

Fig. 7. SCSA Mounting

For detailed actuator information, see Honeywell forms:

— 63-2209 ML6161,ML7161 Product Data Sheet.

— 63-2607 S05,S10,S20 Series Actuator Product Data

Sheet.

M29526

VALVE BODY

VALVE STEM

COUPLER

WING NUT

MOUNTING

PLATE

ANTI-ROTATION

BRACKET

BOLT

STEM ASSEMBLY COVER

SCREWS (2)

HANDLE (REMOVABLE) FOR

MANUALLY ROTATING SHAFT

STEM ASSEMBLY

SCREWS (2)

STEM RETAINER PLATE

BOLT

ANTI-ROTATION

BRACKET

INCLUDED IN REPLACEMENT KIT (PART NO. 5112-11).

THIS PART USED WITH NON-SPRING RETURN ACTUATORS.

M27714

VBN2, VBN3 CONTROL BALL VALVE/ACTUATOR ASSEMBLIES

Automation and Control Solutions

Honeywell International Inc. Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9

http://customer.honeywell.com http://customer.honeywell.ca

® U.S. Registered Trademark

62-0197—04 E.K. Rev. 04-10 Printed in U.S.A.

Fig. 8. VB2 dimensions in inches (mm).

Fig. 9. VB3 dimensions in inches (mm).

M31359

INDICATES FULL PORT VALVE: NO FLOW CHARACTERIZING INSERT.

WILL BE SHORTER WITH NON-SPRING-RETURN ACTUATORS.

PIPE SIZE Cv DIMENSIONS IN INCHES (mm) WEIGHT REPLACEMENT

STEM

ASSEMBLYIN.

1/2

3/4

2-1/2

1-1/4

1-1/2

B,D,E,F,G,H,K

B,D,E,G,H,J,L

N,T

N,P,R,T,U

N,P,R,S,U,1

H,J,K,L,N

L,M,R

(DN)

CODE DESIGNATORS

2-3/8 (60)

J 2-5/8 (67)

K,M

2-3/4 (70)

2-7/8 (73)

M,N 4-5/16 (109)

M,S 3-5/8 (92)

N,1 4-1/16 (103)

P,R,S,1,2 4-15/16 (125)

2-3/4 (70) 7-1/16 (179)

HLP 3-1/16 (78)

4 (102)

5-3/4 (146)

5-5/16 (135)

3 (76) 3-1/8 (79)

3-7/16 (87)

7-3/16 (183)

7-11/16 (195)

7-9/16 (192)

6-15/16 (176)

VBN2A...

VBN2B...

VBN2C...

VBN2F...

VBN2H...

VBN2G...

VBN2D...

VBN2E...

2-3/4 (70)

2-7/8 (73)

3-1/4 (82)

3-3/4 (95)

4-1/16

(103)

3-1/16 (78)

6-7/16 (163)

6-1/2 (165)

6-11/16 (170) 3

(76)

(102)

6-5/8 (168)

6-1/2 (165)

7-3/8 (187)

7 (178)

7-1/16 (180)

7-7/16 (189)

6-3/4 (171)

10-11/16 (271)

8-1/8 (206) 1.0 (0.5) 5112-19

5112-22 (SS)

5112-20

5112-23 (SS)

5112-21

5112-24 (SS)

8-5/16 (211)

8-11/16 (221)

8-1/8 (206)

8-5/16 (211)

8-7/8 (225)

9-1/16 (230)

8-7/8 (225)

10-1/2 (267)

8-11/16 (221) 1.4 (0.6)

2.4 (1.1)

3.2 (1.5)

1.4 (0.6)

C D E F LB (KG)

M31360

INDICATES FULL PORT VALVE: NO FLOW CHARACTERIZING INSERT.

E D

PIPE SIZE Cv WEIGHT REPLACEMENT

STEM ASSEMBLY

DIMENSIONS IN INCHES (mm)

IN.

1/2

3/4

2-1/2

1-1/4

1-1/2

B,D,E,F,H,J

C,D,E,F,G

J,L

L,N,P

P,R ,S ,

H,J,L

H,J,K,M

(DN)

CODE DESIGNATORS

3-1/2 (89)

C,D,E,F,G,K 3-5/16 (84)

4-5/16 (110)

K,M,N 3-5/8 (92)

L,P

R,T 5 (127)

3-13/16 (97)

2-13/16 (71)

7-5/16 (186) 9-1/2 (241)

H,K,M

3 (76)

4 (102)

3 (76) 3-13/16 (97)

4-5/16 (110) 7-13/16 (198) 10-13/16 (275)

VBN2A...

VBN2B...

VBN2C...

VBN2F...

VBN2G...

VBN2D...

VBN2E...

4 (102)

4-1/2 (114)

5-13/16 (148)

3-13/16 (97)

6-1/2 (165)

6-13/16 (173) 3

(76)

(102)

7 (178)

7-13/16 (198)

7-5/16 (186)

7-13/16 (198)

6-13/16 (173)

2-1/16 (52)

2-3/4 (70)

2-13/16 (71)

2 (51) 2.4 (1.1)

2.4 (1.1)

2.8 (1.3)

2.6 (1.2)

3.3 (1.5)

3.8 (1.7)

2.0 (0.9)

5112-19

5112-20

5112-21

3-1/8 (79)

2-7/16 (62)

3-3/16 (81)

3-1/8 (79)

4-1/8 (105)

3-7/8 (98)

2-7/16 (62)

8-13/16 (224)

9-13/16 (249)

9-3/8 (238)

10-13/16 (275)

10-5/16 (262)

11 (279)

12-5/16 (313)

9-13/16 (249)

CDEF GLB(KG)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Controller Handbücher

Honeywell

Honeywell Spyder PUL1012S Bedienungsanleitung

Honeywell

Honeywell Elster Jeavons J125 Bedienungsanleitung

Honeywell

Honeywell S4965V3250 Bedienungs- und Montageanleitung

Honeywell

Honeywell Vista Automation Module Bedienungsanleitung

Honeywell

Honeywell M7061 Bedienungsanleitung

Honeywell

Honeywell ML6984 Bedienungsanleitung

Honeywell

Honeywell T775A/B/M 2000 Series Bedienungsanleitung

Honeywell

Honeywell Stryker VAV Bedienungsanleitung

Honeywell

Honeywell ComfortPoint Open CPO-VAV2A Bedienungsanleitung

Honeywell

Honeywell Z74S-AN Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell S7014A Series Bedienungsanleitung

Honeywell

Honeywell CentraLine LYNX LON CLLYUL1012S Bedienungsanleitung

Honeywell

Honeywell HR 40 F Bedienungsanleitung

Honeywell

Honeywell V7335A 2000 Series Bedienungsanleitung

Honeywell

Honeywell H46C Bedienungsanleitung

Honeywell

Honeywell S9360A Bedienungsanleitung

Honeywell

Honeywell PW6K1ICE Bedienerhandbuch

Honeywell

Honeywell Spyder PUB6438S Bedienungsanleitung

Honeywell

Honeywell LYNX Touch L5200 Series Bedienungsanleitung

Honeywell

Honeywell CENTRA LINE LION CLLIONLC01 Installations- und Betriebshandbuch

Honeywell

Honeywell PRO 2000 Series Bedienungsanleitung

Honeywell

Honeywell BC7000L1000 Handbuch

Honeywell

Honeywell UDC3300 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch