Honeywell EASTOVER 10214 Bedienungsanleitung

EASTOVER 52” CEILING FAN

MODEL #10214

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,

8 am - 5 pm, EST.

Español p. 17

WELCOME

PREPARATION

Before beginning the assembly of this product, ensure

that all parts are present. Compare all parts with the

package contents list and hardware contents list. If

any part is missing or damaged, do not attempt to

assemble the product.

After opening the top of the carton, remove the

mounting hardware package from the foam inserts,

then remove the motor from the packaging and

place it on a soft surface, such as a carpet, to avoid

damage to the nish.

Estimated Assembly Time: Under 60 minutes

Tools Required for Assembly (not included): Electrical

Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Step Ladder, and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape

Measure, Wiring Handbook, and Wire Cutters

CARE AND MAINTENANCE

At least twice each year, lower the canopy to check

the downrod assembly, and then tighten all screws

on the fan. Clean the motor housing with only a soft

brush or lint-free cloth to avoid scratching the nish.

Clean the blades with a lint-free cloth. You may

occasionally apply a light coat of furniture polish to

wood blades for added protection.

Important: Shut o󰀨 the main power supply before you

begin any maintenance tasks. Do not use water or a

damp cloth to clean the ceiling fan.

FAN WEIGHT

The net weight of this fan is: 16.28 lbs. (7,38 kg).

TABLE OF CONTENTS

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

Care and Maintenance ........................2

Package Contents ...........................3

Safety Information ...........................4

Mounting Bracket Installation ...................5

Hanging Your Fan............................6

Wiring .....................................7

Motor Housing Installation .....................8

Blade Installation ............................9

Light Kit Installation .........................10

Final Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Operating Installation . . . . . . . . . . . . . . . . . . . . . . . .13

Replacement Parts List ......................14

Troubleshooting ............................15

Limited Lifetime Warranty.....................16

Unpack your fan and check the contents. You should

have the following items:

1. Upper Mounting Bracket

2. Motor with Lower Mounting Bracket

3. Blade Arm (5)

4. Switch Housing

5. Light Kit

6. Motor Housing

7. Blade (5)

8. E26-base LED Bulbs (2)

9.Glass Bowl

10. Finial Cap

11. Finial

12. Loose parts bags containing (not shown):

Mounting hardware, electrical hardware, pull

chains, wire connectors, etc.

13. Owner’s Manual (not shown)

11 9

PACKAGE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

• Before you begin installing the fan, disconnect the power by removing fuses or turning off the

circuit breakers.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code, and ANSI/NFPA 70-199. Hire a qualied electrician or consult a do-it-yourself wiring handbook if

you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 ft. (2,14 m) from the blades

to the oor and at least 30 in. (76 cm) from the end of the blades to any obstruction.

DANGER

WARNING

When using an existing outlet box, make sure

the outlet box is securely attached to the building

structure and can support the full weight of

the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is

essential in minimizing wobble and noise in the

fan after installation is complete.

To reduce the risk of re or electric shock, do not

use the fan with any solid-state speed-control

device or control the fan speed with a full-range

dimmer switch.

To reduce the risk of re, electric shock, or personal

injury, mount the fan to an outlet box marked

“ACCEPTABLE FOR FAN SUPPORT” and use the

mounting screws provided with the outlet box. Most

outlet boxes commonly used for the support of

lighting xtures are not acceptable for fan support

and may need to be replaced. Consult a qualied

electrician if in doubt. Secure the outlet box directly

to the building structure. The outlet box and its

support must be able to support the moving weight

of the fan at least 35 lbs. (15,88 kg).

WARNING

CAUTION

To reduce the risk of re, electric shock, or

personal injury, do not bend the blade arms

when installing them, balancing the blades, or

cleaning the fan. Do not insert objects between

the rotating fan blades.

Read all instructions and safety information

before installing your new fan. Review the

accompanying assembly diagrams.

Be sure the outlet box is properly grounded or

that a ground (green or bare) wire is present.

! !

7' Min

30" Min

MOUNTING BRACKET INSTALLATION

1. Turn OFF the electrical power at the main fuse or

circuit breaker (Fig. 1).

DANGER: Failure to disconnect the power

supply prior to installation may result in serious

injury or death.

2. Ensure that the blades will be at least 30 in. (76 cm)

from any obstruction and at least 7 ft. (2,13 m) above

the oor (Fig. 2).

3. Secure the upper mounting bracket to the outlet box

using screws provided with the outlet box (Fig. 3).

Note: It is very important that you use the proper

hardware when installing the mounting bracket as

this will support the fan.

Fig. 1

Fig. 2

Fig. 3

Outlet Box

Upper Mounting

Bracket

Bracket Screw

and Washer

Bracket Screw

and Washer

Tab

Screw Hole

Slot

4. Remove the four bracket screws from underneath

the lower mounting bracket and save for later use

(Fig. 4).

Bracket Screw

Washer

Fig. 4

HANGING YOUR FAN

6. Reinstall the previously removed bracket screws

underneath the lower mounting bracket and into

the upper mounting bracket. Securely tighten the

screws (Fig. 6).

Fig. 5

Fig. 6

5. Place tab on the lower mounting bracket into slot in

the upper mounting bracket. Then slide the second

lower mounting bracket tab into the second slot

on the upper mounting bracket until all four screw

holes are in alignment (Fig. 5).

Black (live)

White (neutral)

Bare/Green (ground)

Black

Blue

White

Green

OFF

Black (live)

Second Wire (live)

White (neutral)

Bare/Green (ground)

Black

Blue

White

Green

OFF OFF

Wire Connector

CAUTION

WARNING

If house wires are di󰀨erent colors than referred to in

the following step, stop immediately. A professional

electrician is recommended to determine wiring.

Incorrect wire connection can damage the receiver

and could cause re or injury.

Be sure outlet box is properly grounded or that a

ground (green or bare) wire is present.

! !

Fig. 7

Fig. 8

7. Connect supply and fan wires according to the

diagram (Fig. 7) and these steps:

• Connect the Green wires from mounting bracket to

the Bare/Green (ground) supply wire.

• Connect the Black and Blue wire from the fan to

the Black (live) supply wire.

• Connect the White wire from the fan to the White

(neutral) supply wire.

Secure all wiring connections together with wire

connectors and push all connected wires back into

the outlet box.

8. (Optional) If a second hot power wire is available

from outlet box, connect it to the blue (light power)

wire from the fan for separate light and fan control

(Fig. 8).

Important: The black fan wire is power for fan. The

blue fan wire is power for the light. The white wire

from the fan is common/neutral. The green wires

from the fan and mounting bracket are ground

wires.

WIRING

MOTOR HOUSING INSTALLATION

10. Temporarily lift the motor housing to the mounting

bracket to determine which two motor housing

screws in the sides of the mounting bracket align

with the slotted holes in the top edge of the motor

housing. Partially loosen the two motor housing

mounting screws that align with the slotted holes.

Remove the other two motor housing mounting

screws from opposite sides of the mounting bracket

(Fig. 10).

11. Slide the motor housing over the motor, aligning

the slotted holes in the motor housing with the two

loosened motor housing mounting screws in the

mounting bracket. Twist motor housing to lock. Then

reinstall the two previously-removed motor housing

mounting screws and securely tighten all screws

(Fig. 11).

9. Remove the ten motor screws from the underside of

the motor. Set aside for blade arm assembly (Fig. 9).

Note: A cutout in the tter plate allows easy access

to the motor screw holes.

Mounting

Bracket

Fig. 10

Fig. 11

Motor Housing

Screw

Motor Housing

Screw

Motor

Housing

Motor

Housing

Screws

Motor

Housing

Screws

Fig. 9

Motor Screw

Cut Out

Motor Screw

Cut Out

Blade Arm

Blade

BLADE INSTALLATION

Fig. 13

Cutout

Blade

Twist Lock

Connector

Blade Arm

Fig. 12

12. The blades attach to blade arms using the Fast

AttachTM system.

Align each twist lock connector in the direction of

its corresponding hole in the blade. Place the blade

over the twist lock connectors. Rotate each twist

lock connector so that it is perpendicular to the

hole in the blade. Repeat for the remaining blades

(Fig. 12).

Note: A cut out in the tter plate allows easy access

to the motor screw holes.

13. Insert the two previously removed motor screws

through one blade arm and then into the motor.

Tighten motor screws securely. Repeat with

remaining blade arms, making sure to completely

secure each blade arm before proceeding (Fig. 13).

Motor Screw

LIGHT KIT INSTALLATION

Screw

15. To install the fan with light kit:

Remove screws from the tter plate. Then connect

the plug from the motor assembly to the plug from

the light kit, matching the colors on each plug.

Ensure that the plugs connect tightly (Fig. 15).

Remove the screws from the tter plate. Align

holes in switch housing with holes in upper switch

housing. Reinstall screws that were previously

removed. Use a Phillips screwdriver (not included)

to secure all screws. Plug the hole in the switch

housing with the plastic cap (Fig. 14B). Proceed to

step 20.

Plastic Cap

Nut Washer

14. (Optional) To install the fan without a light kit:

Disconnect the single-pin connectors inside the

switch housing labeled “for light kit connection”

-- black from blue and white from white. Then,

remove the nut and washer located from the

threaded rod in the center of the switch housing to

remove the light kit and wiring (Fig. 14A).

Fig. 14B

Fig. 15

Switch

Housing

Switch

Housing

Plug

Plastic Cap

Screw

Fig. 14A

Light Kit

Washer

Hex Nut

Switch

Housing

Inhaltsverzeichnis

Andere Honeywell Lüfter Handbücher

Honeywell

Honeywell HT-900 Series TURBO FORCE Bedienungsanleitung

Honeywell

Honeywell HYF013 series Bedienungsanleitung

Honeywell

Honeywell PERFECT WINDOW HR150 Bedienungsanleitung

Honeywell

Honeywell HT-216E Bedienungsanleitung

Honeywell

Honeywell ELSTON Bedienungsanleitung

Honeywell

Honeywell HT-22 Bedienungsanleitung

Honeywell

Honeywell HS-216E Bedienungsanleitung

Honeywell

Honeywell LMB HYPER 120-03 Einrichtungshandbuch

Honeywell

Honeywell HR230 Bedienungsanleitung

Honeywell

Honeywell HY254E Bedienungsanleitung

Honeywell

Honeywell QUIETSET HY-254 Series Bedienungsanleitung

Honeywell

Honeywell QUIETSET HT354E Bedienungsanleitung

Honeywell

Honeywell 527HHON001BLK Bedienungsanleitung

Honeywell

Honeywell HY-026 Series Bedienungsanleitung

Honeywell

Honeywell HT-908 Series TECH FORCE Bedienungsanleitung

Honeywell

Honeywell HY108E Bedienungsanleitung

Honeywell

Honeywell HT-380BP - High Velocity Air Circulator Floor... Bedienungsanleitung

Honeywell

Honeywell HTF090 Series Bedienungsanleitung

Honeywell

Honeywell ST9103A Bedienungsanleitung

Honeywell

Honeywell HT-380 Series Bedienungsanleitung

Honeywell

Honeywell HFT-311B Series Bedienungsanleitung

Honeywell

Honeywell HYF290E Bedienungsanleitung

Honeywell

Honeywell DREAMWEAVER Bedienungsanleitung

Honeywell

Honeywell HV-1800E Handbuch

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung