Honeywell NOTIFIER AM-8000 Betriebsanleitung

AM-8000

Programming

Manual

Intelligent Addressable Fire detection

AM-8000 Programming Manual INDEX

AM8000_ind Doc. M-160.2-AM8000-ENG Rev. A.1 NOTIFIER ITALIA

INDEX Programming Manual AM-8000

NOTIFIER ITALIA Doc. M-160.2-AM8000-ENG Rev. A.1 AM8000_ind

INDEX

Definitions 1

Front panel Comands 1

Front Panel LEDs 3

UserInterface 4

Keyboard and Function keys 4

NormalCondition 5

Alarm Condition 6

Fault Condition (Zone) 7

Fault Condition (System) 8

Test Condition (zone alarm in walk-test) 8

List of Disabled elements 9

PROGRAMMINGMenu 10

System 11

Line 12

Timings 12

Password 14

Panel Name 14

PointsProgramming 15

Detectors 15

Modules 22

Auto-Learn 26

Inputs Modules 28

Outputs Modules 28

GROUPS 32

ZONES 35

UTILITY 37

Date and Time 37

SpecialParameters 38

HistoryLOG 41

Display 42

CLEAR 42

Disable 42

AM-8000 Programming Manual INDEX

AM8000_ind Doc. M-160.2-AM8000-ENG Rev. A.1 NOTIFIER ITALIA

Display / Modify Status 43

DetectorsStatus 43

Modules Status 44

Groups Status 45

Zone Status 45

Display Active Modules 46

FIRMWARE version 47

DisabileMenu 48

Detectors 49

Modules 49

Zone 50

System 50

TEST menu 52

Zone 52

LED 53

LCD 53

APPENDIX –CONTROL BY EVENT Equations 54

CBE 54

Operators 55

Examples 59

AM_8000 Programming Manual PAGINA - 1

AM8000_manu-prog-ENG Doc. M-160.2-AM-8000-ENG Rev A1 NOTIFIER ITALIA

Do not try to use the control unit and devices connected without reading this manual

DETECTION SYSTEM LIMITS

An alarm or fire detection system can be very useful for the prompt warning of any dangerous

event

such as fire. In some cases it can automatically manage events (transmission of messages

for room evacuation, automatic fire-extinguishing, TVCC system interface, access route or

door blockage, automatic warning to authorities, etc.), but in any case, it does not ensure

protection against damages to propriety).

Moreover, each system may not properly operate if it is not installed and maintained

according to the manufacturer’s instructions.

It is assumed that the user of this manual has performed a training

course and that he knows the applicable rules in force.

The system and all its components must be installed in an

environment having the following features:

Temperature: -5 °C ¸ +40 °C.

Humidity: 10 % - 93 % (without condensation).

Peripheral devices (sensors, etc.) which are not perfectly compatible

with the control unit may cause damages to the same control unit,

and a bad operation of the system in any moment. Therefore, it is

essential to only use material which is guaranteed by NOTIFIER and

is compatible with its own control units.

Please consult NOTIFIER Technical Service for an

doubt.

DEFINITIONS

LINE: Physical wiring where sensors, addressable Manual Call Points, Sirens, addressable input and

output modules are connected.

POINTS: they are the addressable sensors and modules that can be connected to Lines.

ZONES: they are point groups.

Used as basic indications as stated in EN 54.2 to identify the position of an event.

The maximum number of zones is: 500.

A maximum of 32 points can be associated to each zone.

GROUPS: A group is a software set of devices that can be used to program associations between

Inputs and Outputs and perform actions triggered by input or alarm events.

The control unit is provided with 400 groups.

Pag. 2 Programming Manual SERIEAM

NOTIFIER ITALIA Doc. M-160.2-AM-8000-ENG Rev A1 AM8000_manu-prog-ENG

EVACUATION:

You must know the level 2 password to perform this operation..

Control for the activation of the Siren output and of all output modules programmed with SW-TYPE ID = HORN in absence

of Alarms and Faults. If you press this button once more all the previously activated outputs will be deactivated.

END DELAY:

This button is active only in case of alarm if the immediate activation of the siren outputs in the exclusions menu has been

excluded. The control unit delays the activation of the above-mentioned outputs for the programmed times in the

programmed menu. ( Prog\ Sist\Al. Output Timing ). During the delay time the Active Delay led flashes and it is possible to

re-set the current delay through the Delay Re-set key.

SILENCE ALARM / FAULT:

by pressing this key, the operator can silence the Panel buzzer and is enabled to perform a RESET.

SILENCE / RESOUND SIREN:

You must know the level 2 password to perform this operation..

In case of alarm the following devices are activated: Siren Output, Output modules programmed with SW-Type-ID=HORN ,

the output modules activated for CBE associations

By pressing this key, you can de-activate the following devices:

Siren Output

Output modules programmed through Type-ID HORN enabled for silencing

All output modules activated through CBE associations and enabled for silencing

A subsequent pressure of this key will re-activate :

Siren Output

Output modules programmed through Type-ID HORN

All the output modules de-activated from the previous Silencing

RESET:

the pressure of this key deletes the alarm or fault memory of the current points.

It de-activates the siren and turns off all light signalling of sensors in alarm.

To perform this operation you must know the level 2 password..

FUNCTION KEYS in LCD TOUCH SCREEN:

These keys are displayed in the bottom of the LCD screen.

Activate the corresponding functions. These functions change according to

the selected menus.

Example: in the system status display, these keys allow the access to the

Programming, Utilities, Exclusion menus or the Test menu.

Keys to be used: DURING THE PROGRAMMING or TO ENTER THE PASSWORDS

ARROWS: they are used to perform some selections.

NOTE: pressing and holding one of these keys for more than 1 second, you obtain the key automatic

repetition.

ENTER:after performing a selection, it confirms the entered datum.

ESCAPE:“Back”, it has the menu exit function

AM_8000 Programming Manual PAGINA - 3

AM8000_manu-prog-ENG Doc. M-160.2-AM-8000-ENG Rev A1 NOTIFIER ITALIA

LIGHT SIGNALLINGS OF THE FRONT PANEL

ALARM (Red):

It flashes if there is at least one device in alarm and it has not been recognized yet. It is

permanently lit if all alarm events have been recognized.

ACTIVE REMOTE ALARM (Red):

it is permanently lit if the output towards the fire alarm transmission devices (telephone dial) has

been activated.

SILENCE SOUNDER (Yellow):

It is lit after the Siren Silencing control is performed.

DELAY IN PROGRESS (Yellow):

It is lit if the immediate output activation has been disabled; apply to type C outputs (sounder

output) and type E (alarm transmission through telephone dial). Through this disablement, in case

of alarm the system delays the above mentioned outputs for the programmed times. During the

delay time the led flashes and it is possible to reset the current delay through the “reset delay”

key at lev.1.

ZONE/POINT MASK (Yellow):

It is lit when there is at least one Zone or a Point Disabled in the system.

TEST (Yellow):

It is lit during Zone Walk Test

POWER OK (Green):

It is permanently lit if the control unit is powered (by 230Vac or by batteries).

FAULT (Yellow):

It flashes if there is at least one fault of any type and it has not been recognized yet.

It is on if all faults have been recognized

SYSTEM (Yellow):

It is lit if there is at least a system fault (watch dog, CRC memory error, etc.)

POWER SUPPLIES (Yellow):

It is lit if there is a power supply Fault.

EARTH DISPERSION (Yellow):

It is permanently lit when the positive or negative is earthed.

SOUNDER (Yellow):

It is lit if the siren output is disabled.

It flashes when the siren output is in Fault condition

FAULTS TRANSMISSION (Yellow):

It is lit if the Fault transmission output is disabled (telephone dial).

It flashes when the Fault transmission output is in Fault condition.

ALARM TRANSMISSION (Yellow):

It is lit if the alarm transmission is disabled (telephone dial).

It flashes when the alarm transmission output is in Fault condition

EXTINGUISHING (Yellow):

It is lit if the output towards the automatic fire-fighting system (UDS) is disabled

It flashes when the fire-fighting control output is in Fault condition

Pag. 4 Programming Manual SERIEAM

NOTIFIER ITALIA Doc. M-160.2-AM-8000-ENG Rev A1 AM8000_manu-prog-ENG

Functions and Access level

Functions EN.54 Level Factory default password

Alarm and Faults display Level 1 none

Alarm and Faults recognition Level 1 none

Delay Re-set (appropriate button) Level 1 none

Excluded Zones/Points display Level 1 none

Exclusions menu Level 2 22222

Test Menu Level 2 22222

Utility Menu Level 3 33333

Programming menu Level 3a 44444

Description of the keyboard operation to enter data in the programming folders:

Through the arrows 4 you can enter the adjacent folders (displays)

Through the arrows  you can scroll the fields inside the folder (the selected field is displayed with the

characters in REVERSE.)

If the folder has an index field, the first two function keys appear through which you can scroll

The selected field can be changed by entering in editing mode through the enter key .

According to the type of datum there are different editing modes:

Text entering (CBE, Labels associated with: devices, zones, etc.)

To enter the alphanumerical characters use the keyboard on Touch screen

“Alpha-Numeric” Keyboard on Touch Screen:

This keyboards will be available on the Panel Touch Screen when a Programmable Text have to be edit:

Selections (TYPE-ID, YES, NO, etc..) : type ENTER and through the arrows  all the selectable labels are

scrolled in sequence

The parameter is stored through the enter key ,

If you do not want to store the changes use the escape key

To quit the folder system use the escape key .

To enter the passwords, when they are requested, use the keyboard that appear on the screen.

Confirm the entered password by pressing the ENTER key.

If an invalid password is entered the following message will be

displayed: “Invalid password!: xxxxx “

where “xxxxx” is a 5-character code

This code is used to obtain the programmed password in case it has

been forgotten, by referring to this code to NOTIFIER technical

servicing.

AM_8000 Programming Manual PAGINA - 5

AM8000_manu-prog-ENG Doc. M-160.2-AM-8000-ENG Rev A1 NOTIFIER ITALIA

Function associated with TEST key

input of the test menu.

Refer to Test Menu.

Function associated with DISAB key

input of the test menu.

Refer to Exclusion Men

Function associated with DISABL key

input of the test menu.

Refer to Utility Menu

Function associated with DISAB key

input of the test menu.

Refer to Programming Menu

Normal condition

The following screen is displayed when the control unit is in Normal Condition

Alarm Condition ( with zone events )

The following display appears when the control unit is in condition of zone alarm.

Through the arrow keysyou can scroll the list of the zones containing Faults.

Icons which signals the Panel Conditions.

- The NOTIFIER brand symbol appears in the absence of alarms and Faults.

- If there are Alarms the Fire symbol is displayed

- If there are Faults the Triangle symbol is displayed.

N.B. The alarm state prevails if there are both Alarms and Faults in the control unit

Date - Time

Counter for alarm zones

Counter for Faulty zones

Counter for System Faults

Counter for Excluded zones

Counter for zones

in alarm

FIRST ZONE IN ALARM

Date and Time +

Event Number ID

Text for the Zone

If more zones are in Alarm :

3 ZONES IN ALARM

LAST ZONE IN ALARM

Date and Time +

Event

Number ID

Pag. 6 Programming Manual SERIEAM

NOTIFIER ITALIA Doc. M-160.2-AM-8000-ENG Rev A1 AM8000_manu-prog-ENG

By pressing the enter key you can access the list of point in alarm of the zone selected on the display,

through the arrow keys you can scroll the list of the devices in alarm.

Condition with Fault zone events

The following display appears when the control unit is in condition of zone faults.

Fault events are also initially displayed for zone

Through arrow keys  you can scroll the list of the Zone Faults.

Through a first pressure of the enter key you can display the list of devices with the indication of the point

name; refer to the following figure:

Device in Alarm

D = Detector

M = module

Text programmed

For this Device

Counter

for Faulty zones

Zone with Fault events

Text programmed

for this zone

Andere Handbücher für NOTIFIER AM-8000

Inhaltsverzeichnis

Andere Honeywell Feueralarm Handbücher

Honeywell

Honeywell NOTIFIER IFS-2600 Technisches Dokument

Honeywell

Honeywell ESSER 804950 Bedienungsanleitung

Honeywell

Honeywell Silent Knight 6820EVS Technische Daten

Honeywell

Honeywell SILENT KNIGHT RPS-2000 Bedienungsanleitung

Honeywell

Honeywell Fire-Lite BG-12LX Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT SK-5208 Bedienungsanleitung

Honeywell

Honeywell Silent Knight IntelliKnight 5820XL Bedienungsanleitung

Honeywell

Honeywell ESSER IQ8MCP Bedienungsanleitung

Honeywell

Honeywell Notifier AM12-24 Bedienungsanleitung

Honeywell

Honeywell MA Series Bedienungsanleitung

Honeywell

Honeywell Silent Knight SK318PT Betriebsanleitung

Honeywell

Honeywell 6808 Bedienungsanleitung

Honeywell

Honeywell Notifier ID60 Bedienungsanleitung

Honeywell

Honeywell ESSER Fire Alarm Control Panel Compact Installations- und Betriebshandbuch

Honeywell

Honeywell NOTIFIER MPS-950B Series Bedienungsanleitung

Honeywell

Honeywell NOTIFIER ID61 Bedienungsanleitung

Honeywell

Honeywell HW-TG7LAF02 Installationsanleitung

Honeywell

Honeywell XL 800 Series Bedienungsanleitung

Honeywell

Honeywell Notifier FAAST LT NFXI-ASD Series Bedienungsanleitung

Honeywell

Honeywell NOTIFIER ID2000 Series Bedienungsanleitung

Honeywell

Honeywell NOTIFIER NFS-320C Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT SWIFT Bedienungsanleitung

Honeywell

Honeywell ESSER 761694 Service-Handbuch

Honeywell

Honeywell Gamewell FCI S3 Series Bedienungsanleitung

Beliebte Feueralarm Handbücher anderer Marken

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 Bedienungsanleitung

System Sensor

System Sensor 22051TLE-RF-26 Bedienungsanleitung

Pittway

Pittway Notifier AM2020 Bedienungsanleitung

Ampac

Ampac ZoneSense Bedienungsanleitung

Kidde

Kidde VM-1 Produkthandbuch

LST

LST SIM016-3 Bedienungsanleitung

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Originalbetriebsanleitung

bolid

bolid S2000-IP-03 Bedienungsanleitung

GST

GST DI-9204 Bedienungsanleitung

E2S

E2S BExTBG05D Bedienungsanleitung

Notifier

Notifier UZC-256 Bedienungsanleitung

Fire-Lite Alarms

Fire-Lite Alarms MS-2 Bedienungsanleitung

Siemens

Siemens FDOOT221 Bedienungsanleitung

hyfire

hyfire HY5000 Series Bedienungsanleitung

FlameStop

FlameStop PFSIFP8 Bedienungsanleitung

Radionics

Radionics Radionics 9124 Bedienungsanleitung

UniPOS

UniPOS FD 7120 Bedienungsanleitung

FIREWOLF

FIREWOLF FW-C01224 Bedienungsanleitung