Honeywell HM700A1000 Bedienungsanleitung
QUICK START GUIDE
33-00162-01
HM700A1000
ELECTRODE STEAM HUMIDIFIER
MOUNTING
Mounting Procedure
1. The HM700 humidifier is wall mounted using a key-
hole located on the back of the humidifier.
2. Use #8 x 2 in. (5 cm) screws mounted into 2x4
studs or better if there is drywall or other spacers.
Two screws are needed, one for hanging the unit
and one for securing it so it will not lift off the
keyhole.
3. Install the top screw so that 1/4 in. (6 mm) is
exposed. Raise the unit and place the screw head
through the keyhole.
4. Make sure the unit is level and then insert and
tighten the second screw through the bottom hole.
Tighten the top screw.
Mounting Requirements
Honeywell does not accept responsibility for installation
code violations.
1. Install as close as possible to the steam distributor.
2. Minimize the use of turn or bends in the steam line
as much as feasibly possible.
3. Mount on a suitable wall or vertical surface. Do not
sit the on the floor, where freezing can occur, or on
vibrating surfaces.
4. Allow clearances for plumbing and electrical con-
nections. Consult local and national codes prior to
final location and installation.
5. Install only in areas with ambient temperature
41-104 °F (5-40 °C), and relative humidity 5-95 %
(noncondensing).
6. When possible, mount the HM700 humidifier at a
height convenient for servicing.
Fig. 1. Mounting.
36 in. (92 cm)
duct model
min. front clearance
24 in.(61 cm)
min. height
Mount humidifier
level
As close as
possible to steam
distributor
5-95%
HM700A1000
33-00162—01 2
PLUMBING
Water Supply Requirements
Honeywell does not accept responsibility for installation
code violations. All drain and fill line connections should
be installed in accordance with local plumbing codes by a
licensed plumber.
1. Use 1/2 in. OD copper or plastic supply lines within
4 feet of the humidifier.
2. Install water shut off valve and coupler to facilitate
servicing.
3. Do not use reverse osmosis or de-ionized water.
4. Flush supply lines with fresh clean water after
installing, prior to operating the humidifier.
5. Do not solder/braze copper lines while connected to
the humidifier or the fill solenoid can melt or deform.
6. Water conditions must meet the following criteria for
optimal operation, consult factory for water
conditions outside of this range.
a. Pressure: 30 to 100 PSIG
b. Conductivity: 150-1200 Microsiemens
c. Temperature: 34-68 °F/1-20 °C
d. Hardness 0-10 GPG and Silica 0-4 PPM
–OR–
Hardness 0-3 GPG and Silica 0-14 PPM
Drain Line Requirements
1. Use 7/8 in. copper. Do not use PVC.
2. Install an air gap within three feet of the humidifier.
A copper reducer from 2-1/2 to 7/8 in. is ideal. Do
not allow the drain hose to bottom out in the funnel
cup.
3. The drain line should not end in a sink used
frequently by personnel, or where plumbing codes
prohibit it. Route to a floor drain or equivalent for
safety reasons.
4. Ensure drain line is adequately sloped and sized to
provide free and easy draining.
Fig. 2. Plumbing.
1/2 IN. (30 MM) OD
ALWAYS INSTALL A
WATER SHUT-OFF VALVE.
USE 1/4 IN. COMPRESSION
FITTING (INCLUDED) TO
CONNECT WATER SUPPLY
LINE TO UNIT (LDPE PLASTIC
OR COPPER).
USE 1/2 IN. OD COPPER TO
WITHIN 4 FT (1.2 M) OF HUMIDIFIER.
M35760
1
FILL AND DRAIN LINES CAN ALSO BE
ROUTED THROUGH OPENING IN BACK
OF CABINET.
1
HM700A1000
333-00162—01
ELECTRICAL
CAUTION
Wiring to be performed by a licensed electrician.
This unit must be installed on a GFI Circuit.
CAUTION
Equipment Damage Hazard
Failure to wire the humidifier in accordance with
the wiring instructions could cause permanent
damage. Such errors will void the warranty.
Install Requirements
Honeywell does not accept responsibility for installation
code violations.
1. All electrical connections to the humidifier are to be
done while the unit is switched off, and the external
disconnect is open.
2. Wiring should be done by a licensed electrician.
3. Install a labeled disconnect switch within view of the
humidifier.
Installation Steps
1. Unit requires a dedicated circuit with GFI protection.
Bring circuit to a disconnect near the device to pro-
tect from electrical shock when servicing.
2. Hard wire humidifier to disconnect according as
shown at right.
3. Install factory-supplied jumper between the P termi-
nal and the terminal that corresponds to supply volt-
age.
4. Remove green wire attached to case body and
drain valve (remove canister for access).
5. Clip ground wire as close to drain valve as possible
and remove excess.
Fig. 3. Primary power connection.
NOTES:
— Honeywell requires the use of a GFI circuit on this device to protect the homeowner from electrical shock.
— When installed correctly, the green wire should be removed from the drain valve. The green wire comes
pre-installed from the factory to protect the homeowner in case of an improper installation or when it is not
possible to retrofit a GFI circuit.
— Ensure that adequate power is available to carry full humidifier amp draw as indicated on the specification
label.
— Do not use neutral wire as a ground; connect a dedicated ground to ground termination.
— All wiring to be in accordance with national and local electrical codes.
Hot
Hot
Ground P
240
120
L1
Ground
E
X
T
I
N
T
240 VAC (1 PHASE)
120 VAC (1 PHASE)
Neutral
Hot
Ground P
240
120
L1
Ground
Note:
(Optional)
(Optional)
Connect 120 VAC,
“Hot”, to L1
Note: Power wires can
also be routed through
opening in back of cabinet
HM700A1000
33-00162—01 4
STEAM DISTRIBUTION
Install Requirements
The following instructions must be followed for installation of steam lines for the HM700. Failure to use recommended
material and exceeding maximum recommended length in Table 1, or failure to follow any other steam line installation
instructions will result in improper operation and could void the warranty.
Table 1. Recommended Steam Line Material for HM700 Duct.
*The use of steam line other than copper, stainless steel tube or Honeywell supplied steam line will void the warranty
and may adversely affect the operation of the humidifier.
*When using copper or stainless steel tubing (other than the supplied tubing), insulation is recommended due to high
temperature safety as well as reduced condensate.
To return condensate for HM700, insert copper tube
(supplied with equipment) half way into the condensate
opening of the fill cup along with the spring clamp
(supplied with equipment).
Insert the condensate hose into the condensate return
hole at the top of the HM700, and over the copper tube.
Fasten in place with the spring clamp.
MAIN RULES FOR ATMOSPHERIC STEAM LINES
• Steam lines must not have any restrictions which could result in back pressure.
• Follow recommended materials, size and length, see tables.
• Install steam line in a vertical (upwards) fashion from the HM700 to the distribution nozzle.
• Insulate with 1.0 in. (2.5 cm) pipe insulation.
• Trap condensate (Use full size ‘T’ for Traps)
• Do not over tighten hose clamp at cylinder steam outlet. The maximum torque is 12 in-lbs.
• Support steam line so weight is not on cylinder.
• Condensate traps must be a minimum of 6 in. (15 cm) in height or duct static pressure +2 in. (5 cm), whichever is
greater.
• Trapping by P-trap or pigtail. Support line as necessary to ensure it remains free of kinks.
Voltage
Steam Output Material*Maximum Steam
Line Length Possible Losses
lbs/hr (kg/hr)
Steam
Hose
MED-L
Copper
Tube
Stainless
Steel Tube ft (m) lbs/hr (kg/hr)
110/120V 3.85 1.75 (7/8”) 3/4 in. 0.875 X
0.049W
7 (2) 0.5 (0.2)
220/240V 7.7 3.5 12 (3.5) 1.5 (0.7)
HM700A1000
533-00162—01
INSTALLATION CHECK
Before turning on power to the HM700, inspect the installation to ensure that it was carried out correctly.
Fig. 4. Installation check.
Fused Disconnect
Correct voltage / amps /
phase per spec label
(optional)
Mounting
- Unit level
- Screws into
structural member
Steam Line
- Adequate slope
- No restrictions
- No kinks in hose
- Condensate traps
on long runs
High Limit
On/Off
(optional)
In series between
terminals 1 and 2.
Jumper between terminals
1 and 8 must be removed.
Note:
U or HUM terminals in series
between terminals 1 and 2
Humidity Control
in return duct or
location which
represents humidified
space (no drafts, not
by door, not by
diffuser)
Air Proving
(optional)
In series between
terminals 1 and 2.
Jumper between
terminals 1 and 8
must be removed.
1/2 in. line (minimum) to within 4 ft (1.2 m)
30-100 PSIG
Spec Label
Air Gap
P Trap
with 12 in (30 cm)
minimum drop
Bend, or other
obstruction
HM700A1000
33-00162—01 6
HM700A1000
733-00162—01
HM700A1000
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com
® U.S. Registered Trademark
© 2015 Honeywell International Inc.
33-00162—01 M.S. 11-15
Printed in United States
For more information on maintenance and replacement,
please visit http://yourhome.honeywell.com
or call 1-800-468-1502 or 1-800-814-9452
Andere Handbücher für HM700A1000
2
Inhaltsverzeichnis
Andere Honeywell Luftbefeuchter Handbücher
Honeywell
Honeywell TrueSTEAM HM612A1000/U Bedienungsanleitung
Honeywell
Honeywell HWM 500 - UV Warm Moisture Humidifier Bedienungs- und Wartungshandbuch
Honeywell
Honeywell HE250A1005 Bedienungsanleitung
Honeywell
Honeywell HE365H8908 - Fan Powered Humidifier Bedienungsanleitung
Honeywell
Honeywell HE120 Bedienungsanleitung
Honeywell
Honeywell TrueEASE HE100 Bedienungsanleitung
Honeywell
Honeywell HCM-6009 - QuietCare Lon Console Humidifier Bedienungsanleitung
Honeywell
Honeywell HE120A Bedienungsanleitung
Honeywell
Honeywell HE220A Bedienungsanleitung
Honeywell
Honeywell HE120 Bedienungsanleitung
Honeywell
Honeywell Enviracaire Elite HE365A Bedienungsanleitung
Honeywell
Honeywell HCM-3060 Series Bedienungsanleitung
Honeywell
Honeywell HE240 Bedienungsanleitung
Honeywell
Honeywell HCM-5300E Bedienungsanleitung
Honeywell
Honeywell HE225 Bedienungsanleitung
Honeywell
Honeywell HM512W1005 - TrueSTEAM Lon Wireless... Bedienungsanleitung
Honeywell
Honeywell ULTRA GLOW COOL MIST HUL530 Series Bedienungsanleitung
Honeywell
Honeywell HE120 Bedienungsanleitung
Honeywell
Honeywell TrueEASE HE100 Bedienungsanleitung
Honeywell
Honeywell HE360A - Whole House Powered Humidifier Bedienungsanleitung
