Honeywell TA3840 Bedienungsanleitung

Data Processing Racks

TA3840

Maintenance Manual

SAS au Capital de 2 158 244

€

- 444 871 933 R.C.S. Bourges - APE : 2651B

Headquarter: 9, rueIsaac Newton- 18000 Bourges - France

Data Processing Racks

Maintenance Manual

TA3840

1st

Edition

Released February 2013

INTRODUCTION

This manual is issued specifically for the data processing racks of the TA3840 or EMx40 system.

It contains instructions detailed for functioning, operation and cleaning of this system.

To use it in an optimal way, we advise you TO READ CAREFULLY THESE

INSTRUCTIONS and to respect them throughout the life of the equipment.

Keep this manual to hand so that you can refer to it at any time. Ensure that it is

complete and kept close to the equipment.

The racks TA3840C and TA3840S, as well as the TA3840R repeater module are integrated in the

system for processing the tankers liquid cargo. Maintenance must be carried out by a qualified

operator in communicating electronic systems.

We also draw your attention to the fact that the connection of equipments or the use of products

other than those recommended by HONEYELL MARINE may present risks for which we will not be

liable.

This manual must not be reproduced in any form whatsoever without the prior written approval of

Honeywell Marine who cannot be held responsible for any use of the information contained in this

manual.

As we want you to take advantage of the most of the latest technology and new equipment, as well

as to benefit from our experience, our equipments may undergo technical or design changes. As a

result, some of the features and information in this manual may change without prior notice and

without any obligation to up-date it.

Should you encounter any problems or have any questions about your TA3840 or EMx40 system,

please do not hesitate to contact your nearest Honeywell Marine customer service.

Other documents

The description and the operation of the racks TA3840C/R and TA3840S are described in the

MT5008E technical manual.

The installation of the racks TA3840C/R and TA3840S is described in the MI5008E installation

manual.

SAFETY PRECAUTIONS:

In order to avoid the electric shock or fire hazards, do not expose the equipments

to water projections. Take care to switch the power off before proceeding to any

disconnection or removal of the racks.

Never introduce parts, in particular metal ones, in the air vents of the racks.

Ensure that the racks are well ventilated and that the air vents are not covered.

Take care to maintain the racks distant from

all heat sources (heating

appliances…).

Regulation marking

The manufacturer and specifications plate of TA3840S rack is stuck on the rear face.

Warning:

Our equipments are designed and manufactured in accordance with local

safety regulations, and in particular European directives relative to reconciling

member states' legislation:

●89/336/EEC and 2004/108/EC "Electromagnetic compatibility",

●ATEX 94/9/EC"Equipment and protective systems intended for use in

potentially explosive atmospheres",

●96/98/EC "Marine equipment".

They are intended for professional use and must be installed, used and

maintained by competent staff who is qualified in this type of equipment.

In particular we wish to draw your attention to the fact that we cannot be held

responsible if:

●Any technical alterations are made to our appliances without our written

authorization,

●Our equipments are damaged by being operated in conditions other than

the intended usage of their technical classification (power supply,

temperature, environment, etc.).

The safety instructions given in this manual are merely given for guidance

purposes to protect you and all those using and working on our equipments.

Honeywell Marine cannot foresee all dangerous situations that might arise.

This is why the owner and/or the operator is responsible for the operating

safety of the system.

Regulations of the ship classification society may impose procedures

(health and safety, fire prevention, handling of hazardous substances,

etc.) which are stricter than those given in this manual. In this case, the

regulations must be followed.

Manufacturer's name

and address

Serial number

Manufacturing month and year

EC marking for directive 94/9/EEC,

equipment

– class IIB (refer to

"Technical specifications" paragraph)

EC marking for directive 94/9/EEC,

equipment

– class IIC (refer to

"Technical specifications" paragraph)

TABLE OF CONTENTS

1. SYSTEM DESCRIPTION...............................................................................................................6

Presentation...................................................................................................................................6

Electronic boards............................................................................................................................7

TA3840R - Remote display unit......................................................................................................8

2. SYSTEM MAINTENANCE..............................................................................................................9

Maintenance help...........................................................................................................................9

Software updating ........................................................................................................................13

3. TROUBLESHOOTING GUIDE.....................................................................................................15

4. REMEDIAL MAINTENANCE........................................................................................................19

Recommended spare parts ..........................................................................................................19

Repair procedures........................................................................................................................19

5. SPARE PARTS LIST....................................................................................................................24

6. INFORMATIONS..........................................................................................................................26

Claim report..................................................................................................................................26

Return for repair...........................................................................................................................26

Doc No: MM5008E – Revision 6 – ENG

Data Processing Racks

TA3840 Maintenance Manual

1. SYSTEM DESCRIPTION

Presentation

The racks TA3840C communication unit, TA3840R remote display unit, TA3840S safety unit are

parts of the TA3840 system or EMx40 system, dedicated to monitor the tankers' liquid cargo

parameters such as level, temperature and pressure, as well as all associated measurements, for

the installed transmitters.

The rack TA3840C A/D Analog data collection unit is part of the TA840 System.

The racks TA3840C, TA3840C A/D and TA3840S are installed in a 19" cabinet, whereas the panel

TA3840R is installed in a wall mounting box or provided to be flush mounted in a console.

The general description and the operation of the system are described in the MT5008E technical

manual.

SAFETY PRECAUTIONS:

Maintenance intervention should be carried out on the connections and electronic

boards with electrical power off.

The equipments must be wired up by a qualified electrician. The mains connection,

grounding, circuit breaker and protection must conform to the standards and

regulations in force (these parts are not included in those we supply). We cannot

be held responsible for damage caused directly or indirectly by faulty installation.

Communication

Safety unit

Additional safety

Doc No: MM5008E – Revision 6 – ENG

Data Processing Racks

TA3840 Maintenance Manual

Electronic boards

TA3840C - Communication unit

●Remove the 2 upper screws of the front panel.

Tilt the front panel while maintaining it to prevent that it goes out from its

hinges - Risk of deterioration by falling.

1 Power supply and communication board

2 Control Processing Unit board

3 LCD display board

4 4-20 mA analog inputs boards, 48 channels each (option),

or multifunction boards (option)

TA3840C A/D - Data collection unit

Only the items 1 and 4 are present. The front panel is blind.

TA3840S - Safety unit

●Remove the 2 upper screws of the front panel.

Tilt the front panel while maintaining it to prevent that it goes out from its hinges -

Risk of deterioration by falling.

Doc No: MM5008E – Revision 6 – ENG

Data Processing Racks

TA3840 Maintenance Manual

1 Power supply board

2 Location of Control Processing Unit board (option)

3 Radar transmitter supply board

TA3840R - Remote display unit

●Remove from the back the 6 nuts fixing the front panel using a 7 mm spanner.

1 Communication board

2 LCD display board

up to 7 other radar transmitter

supply boards

Doc No: MM5008E – Revision 6 – ENG

Data Processing Racks

TA3840 Maintenance Manual

2. SYSTEM MAINTENANCE

Maintenance help

●From the main menu of the normal mode, select the UTILITIES menu, then MODE and MNT

(main menu functions are described in the "OPERATION IN NORMAL MODE" chapter of the

MT5008E technical manual).

●Enter the "6854" password or another code chosen at the system definition.

●Push [ENTER], the maintenance mode menu is open.

Maintenance menu functions

Following functions are available from the maintenance menu.

UP Go to the previous page

DOWN Go to the following page

RAW Display of the raw values for a transmitter of the current page

HIST Historic of the system faults

RTN Return to the main menu after confirmation by "Yes" or "No"

MAINTENANCE menu

RAW menu

UP Go to the previous line

DOWN Go to the following line

OFST Offset modification for the displayed transmitter (group 1 and 2 only)

ZLN Zero line modification for the displayed transmitter

ACK Acknowledgment of an alarm started during intervention in maintenance mode

(1 push for each alarm)

RTN Return to the current page or maintenance menu

Doc No: MM5008E – Revision 6 – ENG

Data Processing Racks

TA3840 Maintenance Manual

RAW menu

The RAW menu allows to display the raw values measured by each transmitter and to modify its

measure reference from bottom (zero line). For each radar transmitter of 1 and 2 groups, it is also

possible to modify its measure reference from top (OFFSET).

●From the MAINTENANCE menu, select the page group for the transmitter to be displayed with

UP or DOWN.

●Push RAW , a sub-menu and a dedicated screen for the first transmitter of the group are

displayed.

●Consult the raw values of a transmitter in particular by selecting it with UP or DOWN.

Two types of intervention are then possible, modification of the offset and the zero line.

Various types of displays

Each type of transmitter has its specific display:

●Radar transmitters,

Name Addr Dist

H max

Ofst

Zln

TA01 1 3500 10600 -600 5

Transmitter

name MODBUS

slave No Distance

measured by

the radar

Maximum height

of the tank upright

the radar

Offset

(changeable

parameter)

Distance

zero line

(changeable

parameter)

TmpH

TmpM

TmpL

ADC

Zln

mBAR

210 220 230 1220 50

Individual Temperatures Pressure

code Pressure zero

line (changeable

parameter)

NOTES:

The function keys of certain sub-menus are for transmitter or option selection

shown in this document by the following symbols.

Reminding: [ENTER] key of the numeric keypad appears in this manual under the symbol Ã.

Pushing a forbidden key causes a short beep from the buzzer (if activated).

Andere Handbücher für TA3840

Inhaltsverzeichnis

Andere Honeywell Industrieanlagen Handbücher

Honeywell

Honeywell Miller SkyORB Benutzerhandbuch

Honeywell

Honeywell BA300 Series Montageanleitung

Honeywell

Honeywell HERMetic Bedienungsanleitung

Honeywell

Honeywell Q3300 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER NBG-12WLA Bedienungsanleitung

Honeywell

Honeywell Modutrol IV 41 Series Bedienungsanleitung

Honeywell

Honeywell MICRO SWITCH GLL Series Bedienungsanleitung

Honeywell

Honeywell R8991 Bedienungsanleitung

Honeywell

Honeywell Farenhyt Series Technisches Handbuch

Honeywell

Honeywell MS-9200UDLS Bedienungsanleitung

Honeywell

Honeywell Industrial HERMetic Sampler GTX Chem Bedienungsanleitung

Honeywell

Honeywell F-BO-AFE70 Series Leitfaden

Honeywell

Honeywell VR9105V Bedienungsanleitung

Honeywell

Honeywell PATROL 1b Bedienungsanleitung

Honeywell

Honeywell COMBISAFE Bedienungsanleitung

Honeywell

Honeywell JADE W7220 Bedienungsanleitung

Honeywell

Honeywell RRD Bedienungsanleitung

Honeywell

Honeywell NOTIFIER NBG-12WL Bedienungsanleitung

Honeywell

Honeywell HON 512 Betriebsanleitung

Honeywell

Honeywell HS-700 Bedienungs- und Montageanleitung

Honeywell

Honeywell GENT COMPACT-MAINS-DAU Schulungshandbuch

Honeywell

Honeywell Enraf 1010 CB Betriebsanleitung

Honeywell

Honeywell Q3400A Bedienungsanleitung

Honeywell

Honeywell MILLER 81004170 Bedienerhandbuch

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung