Honeywell TC-RPCXX1 Bedienungsanleitung

EXPERION PKS

RELEASE 516

Redundant Power Supply Installation Guide

EPDOC-X117-en-516A

August 2020

Disclaimer

This document contains Honeywell proprietary information. Information contained herein is to be used

solely for the purpose submitted, and no part of this document or its contents shall be reproduced,

published, or disclosed to a third party without the express permission of Honeywell International Sàrl.

While this information is presented in good faith and believed to be accurate, Honeywell disclaims the

implied warranties of merchantability and fitness for a purpose and makes no express warranties

except as may be stated in its written agreement with and for its customer.

In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The

information and specifications in this document are subject to change without notice.

- 2 -

Contents 3

Chapter 1 - About This Document 4

Chapter 2 - Installation 5

2.1 Preparing for Installation 5

2.1.1 Before you begin 5

2.1.2 Installation declaration 5

2.1.3 Check Components 6

2.1.4 Verify mounting space requirements 7

2.1.5 Component layout recommendations 9

2.1.6 Tools needed 10

2.2 Installing Components 11

2.2.1 Installing redundant power supply 11

2.2.2 Installing redundant power supply chassis adapter 13

2.3 Connecting Components 14

2.3.1 General wiring guidelines 14

2.3.2 Connecting adapter cable 15

2.3.3 Connecting optional annunciator cable 16

2.3.4 Connecting power 17

Chapter 3 - Operation 19

3.1 Activate Redundant Power Supply System 19

3.1.1 Turn on power 19

3.1.2 Interpreting LED indications 19

- 3 -

ABOUT THIS DOCUMENT

This document provides information for installing a redundant power supply for your C200 Controller

and/or I/O chassis.

1.1 Revision history

Revision Date Description

A August 2020 Initial release of the

document.

- 4 -

CHAPTER

INSTALLATION

lPreparing for Installation

lInstalling Components

lConnecting Components

2.1 Preparing for Installation

lBefore you begin

lInstallation declaration

lCheck Components

lVerify mounting space requirements

lComponent layout recommendations

lTools needed

2.1.1 Before you begin

Be sure you have reviewed the

Preinstallation Considerations

in the

Control Hardware Installation

Guide

and confirmed that you have taken steps to minimize Electrostatic Discharge (ESD).

CAUTION

Since power output ratings vary for given approval bodies, be sure the specified load capacity

and temperature rating for the power supply will not be exceeded in your application.

For applicable power output rating specifications, refer to the Experion specifications. The

Experion specifications can be found on the Honeywell website:

(http://www.honeywellprocess.com). Just follow the Experion product links.

2.1.2 Installation declaration

ATTENTION

- 5 -

CHAPTER

This equipment shall be installed in accordance with the requirements of the National Electrical

Code (NEC), ANSI/NFPA 70, or the Canadian Electrical Code (CEC), C22.1. It is supplied as

“open equipment” that is intended to be mounted on a sub-panel within an enclosure. The

suitability of the enclosure and installed system shall be acceptable to the local “authority having

jurisdiction,” as defined in the NEC, or “authorized person” as defined in the CEC.

2.1.3 Check Components

Verify that you have the correct redundant power supply components to meet your particular installation

requirements. The following table lists the available components for reference and the following figure

shows a typical installation configuration.

Note that model numbers beginning with the prefix “TK” are for a coated version of the component.

Model Number Component Quantity per Chassis

TC-RPCXX1 or

TK-RPCXX1

120/240Vac Redundant Power

Supply

TC-RPDXX1 or

TK-RPDXX1

24Vdc Redundant Power Supply 21

TC-RPSCA2 or

TK-RPSCA2

Redundant Power Supply Chassis

Adapter

TC-RPSC04 Redundant Power Supply Cables

[Length is 914mm (3ft)]

User Supplied212-14 AWG Annunciator Wiring

[Maximum Length is 10m (32.8ft)]

1.The redundant power supply models can be mixed or matched, so the quantity would

be 1 per chassis if they were mixed.

2.Optional user-supplied annunciator wiring can be connected to a solid-state relay for

status and troubleshooting purposes.

ATTENTION

If you have a Series A chassis with any of the following model numbers, contact your Honeywell

Service representative for redundant power supply options.

lTC-FXXnn1

lTK-FXXnn1

Note: nn = the number of slots available in the chassis, (04, 07, 10, 13, 17).

- 6 -

Chapter 2 - Installation

Figure 2.1 Typical Redundant Power Supply Application

The redundant power supplies (TC-RPCxx1 or TC-RPDxx1) are surface mounted within 3 feet of the

controller or I/O chassis. A redundant power supply adapter, (TC-RPSCA2) is installed on one end of

the chassis. Three-foot cables, (TC-RPSC04) are installed connecting the redundant power supplies to

the adapter.

2.1.4 Verify mounting space requirements

ATTENTION

Be sure you meet these minimum spacing requirements when mounting components in an

enclosure, as shown in the following Figure.

l10.2cm (4in) between redundant power supplies and the enclosure.

l2.55cm (1in) between redundant power supplies.

l15.3cm (6in) between chassis and heat source.

l5.1cm (2in) between wireway and top or bottom of chassis.

l5.1cm (2in) between wireway and power supply.

l7.7 to 10.2cm (3 to 4in) between chassis mounted horizontally - not shown.

- 7 -

Refer to the dimensions for the appropriate chassis model in the following table to plan the panel layout

for your particular installation. See the

Control Hardware Installation Guide

for more chassis mounting

information.

Chassis Model Dimensions

All models - Right-Side View

- 8 -

Chapter 2 - Installation

Chassis Model Dimensions

TC-FXX042

(With Adapter installed)

TC-FXX072

(With Adapter installed)

TC-FXX102

TK-FXX102

(With Adapter installed)

TC-FXX132

TK-FXX132

(With Adapter installed)

TC-FXX172

(With Adapter installed)

2.1.5 Component layout recommendations

We recommend that you use one of the following recommended layouts for installing redundant power

supply components with one or two chassis.

Recommended Layouts With One Chassis

- 9 -

Recommended Layouts With One Chassis

Recommended Layouts With Two Chassis

2.1.6 Tools needed

l1/8-inch flat-blade screwdriver

l1/4-inch flat-blade (#2) or Phillips screwdriver

lNeedle-nose pliers

lWire stripper

lElectric drill

- 10 -

Chapter 2 - Installation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Stromversorgung Handbücher

Honeywell

Honeywell HP24100ULWP Bedienungsanleitung

Honeywell

Honeywell 9000311PWRSPLY Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT SK-PS6 Bedienungsanleitung

Honeywell

Honeywell HP312CX Bedienungsanleitung

Honeywell

Honeywell Notifier PSU7A Bedienungsanleitung

Honeywell

Honeywell HPTV24-E Series Technisches Handbuch

Honeywell

Honeywell Notifier ACPS-610/E Bedienungsanleitung

Honeywell

Honeywell VX89301PWRSPLY Bedienungsanleitung

Honeywell

Honeywell 208414 Bedienungsanleitung

Honeywell

Honeywell PS1202A00 Bedienungsanleitung

Honeywell

Honeywell HPR2416CBUL Bedienungsanleitung

Honeywell

Honeywell Notifier AMPS-24/E Bedienungsanleitung

Honeywell

Honeywell HP24100WP Technisches Handbuch

Honeywell

Honeywell HPTV2416UL Technisches Handbuch

Honeywell

Honeywell HP300ULM Technisches Handbuch

Honeywell

Honeywell HPF24S8 Bedienungsanleitung

Honeywell

Honeywell 900P01 Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell DCPSU-24 Bedienungsanleitung

Honeywell

Honeywell PS1202C Bedienungsanleitung

Honeywell

Honeywell Gamewell FCI GFPS-9 Bedienungsanleitung

Honeywell

Honeywell HPF24S8 Technisches Handbuch

Honeywell

Honeywell PEHA D 942 SPV Bedienungsanleitung

Honeywell

Honeywell NOTIFIER FCPS-24S6 Bedienungsanleitung

Honeywell

Honeywell PRO32E1PS Gebrauchsanweisung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung