Honeywell SeqLED E SET-30 Bedienungsanleitung

SeqLED E

70mm

160mm

70mm

26mm

Dimensional Drawings:

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

Installation:

Step 2: Unfasten the four retaining screws without removing them and remove the diffusor.

Step 3: Set the module address. For more information about module settings see the next

page.

Step 1: Unfasten the front screw and remove the cover.

Weight:

Technical description

Part no.:

Lumen output:

-30 to 60 C

Up to 95%

Produced in accordance with:

Ambient Temperature Range:

Maximum Power Consumption:

Operation Voltage: 220-240V AC/DC, 50-60 Hz

280 lm

500 gr

3.8W / 4.2VA

138005.S30

SeqLED E SET-30 230V

Relative Humidity:

Technical lifetime (light source): > 100000 hours

IP65

Degress of cover protection:

EN 60598-1, EN 60598-2-22, EN 55015

EN 61547, EN 61000-3-2, EN 61000-3-3

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

PE N L

washer

rubber

o-ring

PE N L

MOUNTING METHODS

Surface mounting on the wall

INSTALLATION

Step 1: Unfasten the front screw and remove the cover. Next, unfasten the four retaining screws without

removing them and remove the diffusor.

Step 3: Use a drill with a 3,5mm bit to open the 4 mounting holes located in the plastic base. Place the

luminaire on the desired mounting location and mark and drill these 4 holes. Fit the supplied 4

plastic mounting plugs to these drilled holes on the mounting location.

Step 2: Install the supplied cable gasket from the inside of the plastic base.

Step 4: Open a cable entry cutout hole on the plastic base and install the supplied cable gasket. Make a

hole in the center into the desired gasket by using a small screwdriver and pass the round cable

through the gasket. Connect the main cables to the respective terminal block: N for neutral, L for

live wire and PE for ground wire. Install the included tie (if needed) to fasten securely the power

cables. Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type

2x1mm² or any other type, at least equal to it's mechanical and electrical properties). ATTENTION!!

The cable must not be deformed in any way (This requirement is important to ensure the IP rating).

Step 6: Re-install the diffusor, fasten the four retaining screws, refit the cover and fasten the screw that

was removed in step 1.

Step 5: Mount the base to the desired location by using the supplied screws, washers and o-rings in

each mounting hole.

At the end of their useful life the packaging and product

should be disposed of via a suitable recycling centre.

Do not dispose of with your normal household waste.

Do not burn.

The light source contained in this luminary shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

MODULE FOR SINGLE LAMP SELECTION AND MONITORING

Switching of one selected light in the electric circuit

SET010 select

DIP-switch 1

ON for non-maintained mode (Default)

DIP-switch 2

OFF for lighting address 1-16 (Default)

ON for lighting address 17-32

Indicator LED

Rotary coding switch

for setting the exact lamp adress DIP-switch 3 (OFF)

Attention!

Connect L and N correctly!

Exchanging L and N causes malfunction.

Setting the lighting address is carried out by a rotary coding switch that is easily accessible from the

outside.

The module is already prepared for administering a total of 32 lighting addresses.

Function

By means of a suitable control, it is possible with the aid of the SET010 select to determine whether the

lamp connected to it is ready for use or faulty.

Lighting addresses 1 to 16 can be slected when DIP switch 2 is set at OFF.

The address range 17 to 32 can be selected by setting DIP switch 2 to ON.

Settings

(DIP switch 2 = ON and rotary coding switch = 1 is equivalent to lighting address 17 etc.)

Technical description

Cross section:

Temperature:

Dimensions (L x W x H in mm) 78 x 30 x 20

Max: 1.5mm

-30°C up to +60°C, T =+75°C

cmax

SET010 select

Prewired

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Relais Handbücher

Honeywell

Honeywell RA889A Bedienungsanleitung

Honeywell

Honeywell Aquastat L8124B Bedienungsanleitung

Honeywell

Honeywell Farenhyt Series Bedienungsanleitung

Honeywell

Honeywell SILENT KNIGHT IDP-Relay Bedienungsanleitung

Honeywell

Honeywell R132A Kurzanleitung

Honeywell

Honeywell TRIPLEAQUASTAT L8151A Bedienungsanleitung

Honeywell

Honeywell Aquastat L8148A Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell Silent Knight SK-Relay Bedienungsanleitung

Honeywell

Honeywell Aquastat L8148A Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell TRADELINE R8184G Bedienungsanleitung

Honeywell

Honeywell Silent Knight WSK-RELAY Bedienungsanleitung

Honeywell

Honeywell BDR91 Bedienungsanleitung

Honeywell

Honeywell HPSR103 Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES RM7895A Bedienungsanleitung

Honeywell

Honeywell RM7897A Bedienungsanleitung

Honeywell

Honeywell R841C-E Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Honeywell

Honeywell Notifier SKBR3N Bedienungsanleitung

Honeywell

Honeywell R182J Bedienungsanleitung

Honeywell

Honeywell 7800 SERIES Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Pilz

Pilz PNOZ X10 Betriebsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung