Honeywell 2050 Bedienungsanleitung

Operation & Installation Guide

Model 2050 / 2050E

Read These Instructions Very Carefully!

Limited Warranty

Home and Ofﬁce Security Safes

MHAS2050E0807

ENGLISH

If your Honeywell safe fails to operate because of a manufacturing defect any time up to ﬁve (5)

years from the date of original purchase, we will, at our discretion, repair or replace the unit at no

charge to the original owner. A copy of your sales receipt is required as Proof of Purchase.

The consumer must ﬁrst contact SISCO® Customer Service (800-223-8566, USA and Canada;

310-638-1182 outside of USA and Canada, or via E-mail at [email protected])

during the Term of the Limited Warranty for authorization on the repair or replacement of the safe.

For the repair of the safe, SISCO Customer Service may provide approval for taking it to a local

locksmith. For the replacement of the safe, the consumer must return it, prepaid, to SISCO

(2835 E. Ana St., Rancho Dominguez, CA 90221). SISCO will replace the safe with a comparable

model, shipping prepaid.

WHAT IS NOT COVERED

SISCO’s responsibility and the consumer’s rights are limited to the repair or replacement of the

defective safe, as stated above.

This Warranty does not apply if the product has been damaged by improper installation, neglect,

accident, misuse, exposure to extremes of heat or humidity, terrorism, war, acts of God, or as a

result of service or modiﬁcation by other than an authorized service center. While your SISCO safe is

warranted to be free of mechanical defect during the Term of Limited Warranty, the Warranty does

not apply to the ﬁnish of the safe.

SISCO is not responsible for any costs associated with removing or installing this product.

SISCO is not responsible for damage or loss of the contents of the safe nor for the unauthorized

removal of contents.

SISCO is not responsible for any damages incurred to the safe during shipment.

This Limited Warranty applies only to new SISCO safes, purchased by the original owner, and is not

transferable to second owners or “factory seconds” safes purchased by the consumer.

No implied Warranty of salability or ﬁtness exists other than those descriptions provided on the

packaging, instructions and advertising. No other covenants or warranties, either implied or stated,

written or oral, are hereby present. Some states do not allow limitations on how long an implied

Warranty lasts, so the above limitations may not apply to you.

This Warranty gives you speciﬁc rights and you may also have other rights which vary from state to

state.

The Honeywell trademark for Home/Ofﬁce Safes is used with permission. Honeywell Safes are

distributed exclusively by SISCO. Honeywell makes no representations or warranties with respect to

this product or service. The Honeywell Trademark is used under license from Honeywell Intellectual

Properties Inc. by SISCO.

Safe Identiﬁcation Record

Home and Ofﬁce Security Safes

For Your Protection

• Do not remove the Serial Number tag from the safe.

• Store Emergency Override Keys away from (NEVER INSIDE) safe.

• Record all Safe Identiﬁcation Numbers on Safe Identiﬁcation

Record (last page).

• Save this manual and NEVER keep it inside the safe.

Overview of Your Safe ...................................

Opening Safe For The First Time................

Programming a Personal Passcode ...........

Using the Emergency

Override Key.....................................................

Checking, Changing and Installing

New Batteries...................................................

Additional Features .......................................

Use, Care and Maintenance ........................

Customer Support ..........................................

Page 1

Page 2

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Index

Model Number

Serial Number

Key Number

Digital Passcode Record

Your Passcode must be at least 3 digits and no more than 9 digits followed

by the # key.

Important:

Once your personal Passcode is programmed, the factory pre-set code will no

longer open the safe.

Overview of Your Safe

WELCOME!

Your new Honeywell Anti-Theft™ Safe will provide years of safe and secure

protection for your valuables, important documents and other personal items.

All Honeywell safes are designed and built using the highest manufacturing

standards to ensure maximum user satisfaction under a variety of conditions.

With proper care, your Honeywell safe will provide “Peace of Mind” for many

years to come.

Thank you and Enjoy!

The following list outlines the items and quantities of each included with

your new safe. Please carefully check the list to conﬁrm all items have been

received. If any item is missing, then please contact Customer Service

at 1-800-223-8566.

(A) Operation & Installation Guide 1 ea.

(B) Emergency Override Key 2 ea.

(D) Felt Floor Mat 1 ea.

(E) Permanent Mounting Template 1 ea.

(F) “AA” Batteries 4 ea.

Home and Ofﬁce Security Safes

Important: DO NOT RETURN SAFE TO STORE

If you are missing parts, have difﬁculty programming your safe or

have any other questions pertaining to its proper use and care, DO

NOT RETURN your safe to the store. Please contact Customer Service

at 1-800-223-8566 (USA & Canada) for assistance.

Notes

Opening Safe For The First Time

Home and Ofﬁce Security Safes

Opening Your Safe for the First Time Using

the Pre-set Factory Code

Batteries have been pre-installed at the factory. Using the

factory pre-set Passcode 159#, open the safe as follows:

1. Enter the three digit Factory Passcode 159 on the keypad

followed by the #Symbol. If entered correctly, the green

LED will light and the lock will click.

2. Rotate the small handle on the knob clockwise to the

right, and then pull the door open.

3. A fast blinking amber light indicates that the Passcode was

entered incorrectly. Re-enter the correct Passcode and

try again.

Security Lockout:

The safe is designed to lock out the keypad function if the wrong Passcode is

entered multiple times.

• After the 3rd error: 20 second lock-out. (waiting period)

• 4-6 errors: 5 minute lock-out.

• 7+ errors: 1 hour lock-out.

If you have forgotten the Passcode, entry can be made using the Emergency

Override Key. (See page 4).

Important:

If no action is taken, the safe will automatically relock in 5 seconds and the

Passcode will need to be re-entered.

Closing Your Safe

1. Make sure nothing inside the safe is obstructing the door from completely

closing.

2. Rotate the knob counterclockwise to the left and the safe will lock.

Notes

Amber

Light

Green

Light

# Symbol

Rotate

right

to open

10 3

Home and Ofﬁce Security Safes

Programming a

Personal Passcode

Programming Your Personal Passcode

For security reasons, it is very important that you program your

own personal Passcode into the digital lock. The factory Passcode

159# should be changed immediately.

1. Using the factory assigned Passcode (159#), open the safe.

(See page 2).

2. Locate and then press and release the small red memory

button located near the bottom hinge on the inside of the

door. The keypad will beep three times and the amber LED

will light.

3. Select a Passcode using 3 to 9 numbers (no letters) and

enter it on the keypad, followed by the #sign.

4. The keypad will again beep three times and the amber

LED will light. This will complete the programming of your

personal Passcode. Leave the door open and proceed to

Testing Your New Passcode.

Testing Your New Passcode

1. With the door in the open position, rotate the knob counter-

clockwise to the left. In about 3 seconds the safe will

automatically lock.

2. Enter your new personal Passcode onto the keypad followed

by the # key and the digital lock should click open.

Example:

3. Rotate the knob clockwise to the right to conﬁrm that your

newly programmed Passcode opens the safe.

4. If the new Passcode does not unlock the safe, then repeat

the steps to program your personal Passcode and retest.

Once programming is completed, write your personal Passcode

down and store it in a safe and secure place away from the safe.

Important:

Your new Passcode will always consist of your selected number code followed by the #

Key. Once you have programmed your personal Passcode, the pre-set factory code will

no longer open the safe.

Amber Light

# Symbol

Memory

Button

Notes

3 52

Home and Ofﬁce Security Safes

Using the Emergency

Override Key

Using the Emergency Override Key

Your safe is equipped with an Emergency Override Key which

allows immediate access in case you forget your Passcode or the

batteries need replacing.

1. Press ﬁrmly in on the dotted arrow on the front of the

battery cover and push downward to open.

2. Remove 4-AA Batteries.

3. Insert one of the Emergency Override Keys (2 included) into

the bypass lock located behind the batteries, and turn to the

right.

4. Rotate the knob clockwise to the right and pull door open.

5. With door in the open position, turn the Emergency

Override Key to the left and remove it from lock.

6. Re-insert the 4-AA batteries. If required, replace discharged

batteries with a new set. (Page 5)

7. Replace the battery cover, and with the door still open, test

your new Passcode. If your current Passcode has been

forgotten or no longer works, re-program a new Passcode

(Page 3) and retest.

8. Lock the safe and return the Emergency Override Key to a

secure location away from the safe.

Battery Cover Remove Batteries Insert Override Key

Customer Support

How to Contact Us

Phone: 1-800-223-8566 (USA and Canada)

Monday through Friday, 7:30 am to 4:30 pm Paciﬁc Standard Time

Email: CustomerSer[email protected]

In addition to the required information regarding your safe, you must include the

best time and proper telephone number to reach you during our normal Customer

Service hours.

Mail: Attn: Customer Service Dept.

SISCO

2835 E. Ana Street

Rancho Dominguez, CA 90221

Internet: www.HoneywellSafes.com

Ordering Replacement Keys

If a key becomes misplaced or you would like additional keys, you may conveniently

purchase them from our Customer Service Department. You must supply the following

information to assure accurate processing:

• Name / Address / Telephone

• Safe Model Number / Serial Number

• Key Number (located on the key and Emergency Override Key lock cover)

• Number of keys requested

• E-mail address if available

AUSTRALIA

Mail:

Customer Service Dept.

Master Distributors

11 Howleys Rd.

Notting Hill VIC 3168

03-9538-9200

EUROPE

Mail:

Freightways Distriservices B.V.

P.O. Box 3077

2220 CB Katwij

The Netherlands

+31(0) 71.409.0721

Payment and Delivery

In the USA, replacement keys are available for a fee and credit card orders are accepted

by telephone or via our web site. Checks or Money Orders are required for orders

received by mail and should be made payable to SISCO®. Contact our Customer

Service Department for costing information prior to ordering.

Home and Ofﬁce Security Safes

Checking, Changing and

Installing New Batteries

Your new safe arrived with 4-AA batteries pre-installed at the factory. It is important

to periodically check the batteries and, if necessary, replace with a new set.

Checking Batteries

1. Locate the # key on the keypad and press.

2. If the amber LED ﬂashes and you hear a beep, the batteries

are good.

3. If the red LED ﬂashes, change the batteries within two

months.

4. If the LED does not light, then you must replace the

batteries immediately.

5. Proceed to Changing and Installing New Batteries.

Changing and Installing New Batteries

1. Press ﬁrmly in on the dotted arrow on the front of the

battery cover and push downward to open.

2. Remove the 4 dead batteries and replace with 4 new

Alkaline AA batteries. Make sure that they are installed in

the proper direction.

3. Replace the cover and open the safe using your personal

Passcode.

NOTE: Proper disposal of discharged batteries is encouraged!

Important:

Replacing the batteries will not erase your personal Passcode from memory. However,

weak or dead batteries will prevent the use of the digital key pad. Access to the safe

will have to be made using the Emergency Override Key. (See page 4).

# Symbol

Battery Cover Remove Batteries

Customer Support

Your Safe’s Unique Identiﬁcation Numbers

When contacting Customer Service, you should be prepared to supply some

important information that speciﬁcally identiﬁes your safe. This information is

extremely important to assuring prompt and accurate customer assistance.

It is strongly recommended that you identify and record the following information

in the “Safe Identiﬁcation Record” form located on the inside back cover of this

manual:

Model Number

Serial Number

Key Number

Locating Model and Serial Numbers

Most Honeywell safes include a small metallic silver or gray tag afﬁxed to one

of the surfaces. This tag is usually located on the front or right side of the safe.

This tag contains the Serial Number, and on selected models a similar tag is

attached containing the Model Number. If a Model Number tag is not attached

to the safe, then it can be located on the front or side panel of the box that the

safe was packaged in. Write this number down for future reference.

Locating Key Number

The Key Number is engraved on the top portion of the key and on the lock

cylinder. This number should also be written down and retained for future

reference.

Important: DO NOT REMOVE TAGS!

In case your safe becomes inoperable or you lose your keys, these identiﬁcation

numbers will be needed to correct the problem. It is recommended that the

number tags remain in place on the safe. If removal is necessary, then they

should be attached to the inside back cover of the Operation and Installation

Guide. Store in a safe and secure place for future reference.

Home and Ofﬁce Security Safes

Use, Care and Maintenance

Safe Care and Maintenance

When properly maintained, your safe will continue to operate and accurately

read the authorized Passcode for many years. In order to ensure optimum

performance of your safe, please follow these simple precautions:

Replace Batteries – For best results and performance, we recommend that the

batteries be replaced at least once a year or sooner depending on amount of

use.

Clean Hands - Never attempt to operate the digital keypad if your hands have

excessive dirt, debris or liquids on them.

Clean Safe – To clean the surface of your safe, it is recommended that you

use a mild cleaner (e.g., window cleaner) to avoid scratching or discoloring

the surface. Always wipe dry and NEVER use abrasive cleansers on the safe or

digital keypad.

For future reference, store this Operation and Installation Guide in a secure area

away from the safe. DO NOT DISCARD!

Additional Features

Mounting Hardware Kit

Many customers prefer to bolt their safe to the wall or ﬂoor to increase protection

from theft and resistance to tipping. This safe was manufactured with (4) bolt-down

holes pre-drilled in the back panel and (4) in the ﬂoor.

To secure your safe to the wall and/or ﬂoor:

1. Remove the felt liner from the ﬂoor of the safe and locate the pre-drilled holes.

2. Anchor the safe using the Mounting Hardware Kit which includes (4) anchor

bolts. (See mounting template) Back of unit can be secured to a back wall or wall

studs using wood screws or toggle bolts.

3. Once completed, replace felt pad.

Important:

If you have questions regarding how to permanently secure the safe or are

uncomfortable using the tools necessary to complete the project, please check with

your local retailer, home center or independent contractor.

Home and Ofﬁce Security Safes

Use, Care and Maintenance

Safe Care and Maintenance

When properly maintained, your safe will continue to operate and accurately

read the authorized Passcode for many years. In order to ensure optimum

performance of your safe, please follow these simple precautions:

Replace Batteries – For best results and performance, we recommend that the

batteries be replaced at least once a year or sooner depending on amount of

use.

Clean Hands - Never attempt to operate the digital keypad if your hands have

excessive dirt, debris or liquids on them.

Clean Safe – To clean the surface of your safe, it is recommended that you

use a mild cleaner (e.g., window cleaner) to avoid scratching or discoloring

the surface. Always wipe dry and NEVER use abrasive cleansers on the safe or

digital keypad.

For future reference, store this Operation and Installation Guide in a secure area

away from the safe. DO NOT DISCARD!

Additional Features

Mounting Hardware Kit

Many customers prefer to bolt their safe to the wall or ﬂoor to increase protection

from theft and resistance to tipping. This safe was manufactured with (4) bolt-down

holes pre-drilled in the back panel and (4) in the ﬂoor.

To secure your safe to the wall and/or ﬂoor:

1. Remove the felt liner from the ﬂoor of the safe and locate the pre-drilled holes.

2. Anchor the safe using the Mounting Hardware Kit which includes (4) anchor

bolts. (See mounting template) Back of unit can be secured to a back wall or wall

studs using wood screws or toggle bolts.

3. Once completed, replace felt pad.

Important:

If you have questions regarding how to permanently secure the safe or are

uncomfortable using the tools necessary to complete the project, please check with

your local retailer, home center or independent contractor.

Home and Ofﬁce Security Safes

Checking, Changing and

Installing New Batteries

Your new safe arrived with 4-AA batteries pre-installed at the factory. It is important

to periodically check the batteries and, if necessary, replace with a new set.

Checking Batteries

1. Locate the # key on the keypad and press.

2. If the amber LED ﬂashes and you hear a beep, the batteries

are good.

3. If the red LED ﬂashes, change the batteries within two

months.

4. If the LED does not light, then you must replace the

batteries immediately.

5. Proceed to Changing and Installing New Batteries.

Changing and Installing New Batteries

1. Press ﬁrmly in on the dotted arrow on the front of the

battery cover and push downward to open.

2. Remove the 4 dead batteries and replace with 4 new

Alkaline AA batteries. Make sure that they are installed in

the proper direction.

3. Replace the cover and open the safe using your personal

Passcode.

NOTE: Proper disposal of discharged batteries is encouraged!

Important:

Replacing the batteries will not erase your personal Passcode from memory. However,

weak or dead batteries will prevent the use of the digital key pad. Access to the safe

will have to be made using the Emergency Override Key. (See page 4).

# Symbol

Battery Cover Remove Batteries

Customer Support

Your Safe’s Unique Identiﬁcation Numbers

When contacting Customer Service, you should be prepared to supply some

important information that speciﬁcally identiﬁes your safe. This information is

extremely important to assuring prompt and accurate customer assistance.

It is strongly recommended that you identify and record the following information

in the “Safe Identiﬁcation Record” form located on the inside back cover of this

manual:

Model Number

Serial Number

Key Number

Locating Model and Serial Numbers

Most Honeywell safes include a small metallic silver or gray tag afﬁxed to one

of the surfaces. This tag is usually located on the front or right side of the safe.

This tag contains the Serial Number, and on selected models a similar tag is

attached containing the Model Number. If a Model Number tag is not attached

to the safe, then it can be located on the front or side panel of the box that the

safe was packaged in. Write this number down for future reference.

Locating Key Number

The Key Number is engraved on the top portion of the key and on the lock

cylinder. This number should also be written down and retained for future

reference.

Important: DO NOT REMOVE TAGS!

In case your safe becomes inoperable or you lose your keys, these identiﬁcation

numbers will be needed to correct the problem. It is recommended that the

number tags remain in place on the safe. If removal is necessary, then they

should be attached to the inside back cover of the Operation and Installation

Guide. Store in a safe and secure place for future reference.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Sicher Handbücher

Honeywell

Honeywell 2208 Bedienungsanleitung

Honeywell

Honeywell 2072 - 1.00 Cubic Foot Anti-Theft Shelf Safe Anleitung zur Verwendung

Honeywell

Honeywell 2101 Bedienungsanleitung

Honeywell

Honeywell 5410 Anleitung zur Verwendung

Honeywell

Honeywell 2605 Anleitung zur Verwendung

Honeywell

Honeywell Media Protector 2040 Bedienungsanleitung

Honeywell

Honeywell 3518 Bedienungsanleitung

Honeywell

Honeywell 2208 Bedienungsanleitung

Honeywell

Honeywell 5605 Bedienungsanleitung

Honeywell

Honeywell 5403 Bedienungsanleitung

Honeywell

Honeywell 5113 Bedienungsanleitung

Honeywell

Honeywell 2111 Bedienungsanleitung

Honeywell

Honeywell 5805 Bedienungsanleitung

Honeywell

Honeywell 5005B Bedienungsanleitung

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Bedienungsanleitung

Honeywell

Honeywell 5911 Bedienungsanleitung

Honeywell

Honeywell 1101 Bedienungsanleitung

Honeywell

Honeywell 2901 Bedienungsanleitung

Honeywell

Honeywell 5002 Bedienungsanleitung

Honeywell

Honeywell 2116 Bedienungsanleitung

Honeywell

Honeywell 2605 Bedienungsanleitung

Honeywell

Honeywell 5301DOJ Bedienungsanleitung

Honeywell

Honeywell 5005 Anleitung zur Verwendung

Honeywell

Honeywell 5101 Bedienungsanleitung

Beliebte Sicher Handbücher anderer Marken

Squire

Squire Stronghold Keysafe Bedienungsanleitung

Phoenix

Phoenix FS0352C Produktinformationsblatt

Phoenix

Phoenix KS0030E Series Bedienungsanleitung

Vaultek

Vaultek 10 Series Technisches Datenblatt

Arregui

Arregui CLASS Bedienungsanleitung

Beaumont

Beaumont SMART KEYBOX Bedienungsanleitung

Hornady

Hornady SnapSafe Trunk Safe II Bedienungsanleitung

SPORTS AFIELD

SPORTS AFIELD SA-HD5-BIO Bedienungsanleitung

Phoenix

Phoenix FS1280F Bedienungsanleitung

Phoenix

Phoenix SS0992K Produktinformationsblatt

Technomax

Technomax Trony Series Handbuch

SPORTS AFIELD

SPORTS AFIELD INSTINCT BIOMETRIC Series Bedienungsanleitung

RICHTER CZECH

RICHTER CZECH LA Bedienungsanleitung

Olymp

Olymp GOsafe 110 Bedienungsanleitung

Phoenix

Phoenix SS0100E Produktinformationsblatt

Clarke

Clarke Strong-Arm CS1000K Bedienungsanleitung

Ankaro

Ankaro ANK EZ I Bedienungsanleitung

Phoenix

Phoenix FS1270E Series Bedienungsanleitung