Honeywell ACUIX Bedienungsanleitung

Document 800-03542 Rev A

12/08 1

ACUIXTM Fixed Camera Dome:

Single or Double Ball Joint

Stick Mount

Indoor Pendant Housing

Quick Installation Guide

1Introduction

Caution The maximum camera and lens weight that can be

installed in the housing is 2 pounds (0.91 kg).

Note The fixed camera is selected by the end user. Install a

camera with a ¼”-20 tripod mount and ensure that the

size of the camera and lens allow enough room to aim

and adjust the lens within the contraints of the housing.

Note It is the installer’s responsibility to complete the wiring

and required connections based on the camera

selected.

Figure 1 External Dome Layout

2Install the Mount or Adapter

The indoor pendant housing has optional mounts and adapters available.

See Figure 2.

Threaded nipple

Housing

Lower dome

Figure 2 Indoor Mounts and Adapters

2a Installing a Wall Mount and Optional Pole or Corner

Adapters

The HDXWM1 wall mount is designed specifically for the ACUIX and can be

mounted directly to a vertical load-bearing surface. It supports up to 25

pounds (11.7 kg).

Figure 3 Wall Mount Dimensions

1. Route the field wiring as required through the wall, pendant housing

wiring access hole, and then through the wall mount.

Approximately one foot (0.3 m) of cable must extend past the mount for

all installations.

• If installing with a corner or pole adapter also route the field wiring

through the corner or pole adapter hole.

Ceiling Mount

(HDCM1)

Wall Mount

(HDXWM1)

Pole Mount Adapter

(HDXPMA1)

Corner Adapter

(HDXCMA1)

4.13” (105.0 mm)

0.28” diameter

(7.00 mm)

3.94” (100.0 mm)

5.71” (145 mm)

9.84”(250 mm)

ACUIX Stick Mount Quick Installation Guide

2. (Optional) If you are installing the wall mount with a corner adapter

(HDXCMA1) or pole mount adapter (HDXPMA1) then:

Pole Adapter

• Secure the pole mounting bracket to the pole using hardware

specifically designed for the surface/material. There are four

cutouts (two on each side), 0.24” x 0.75” (6 mm x 19 mm), to

accommodate straps to secure the pole mounting bracket to a

pole. See Figure 4.

Corner Adapter

• Secure the corner bracket using hardware specifically designed

for the surface/material. The bracket has eight 0.39” (10.0 mm)

holes; four on each side. See Figure 5.

3. (Optional): If you are installing with a corner or pole adapter, line up the

hole pattern on the wall mount with the hole pattern on the corner or

pole adapters.

4. Secure the wall mount to the wall using hardware specifically designed

for the surface. There are four 0.28” (7.00 mm) diameter mounting

holes for securing the mount.

Figure 4 Pole Mount Adapter Dimensions (HDXPMA1)

6.1" (155 mm)

6.69" (170 mm)

1" (25.4 mm)

diameter

4 cutouts (2 on each side)

3.3"(84mm)

55 degrees

4.6" (116.8 mm)

Figure 5 Corner Adapter Dimensions (HDXCMA1)

2b Installing a Ceiling Mount

The ceiling mount is installed directly to a horizontal load-bearing surface

and supports up to 25 pounds (11.7 kg).

1. Route field wiring as required into the wiring access hole and through

the center of the ceiling mount.

Approximately one foot (0.3 m) of cable must extend past the mount.

2. Secure the ceiling mount to the ceiling using hardware specifically

designed for the surface.

There are four 0.47” (12.00 mm) diameter mounting holes for securing

the mount. See Figure 6.

90 degrees

5.43"(138mm)

6.3" (160 mm)

3.94" (100 mm)

6.89" (175 mm)

0.39" (10 mm) diameter (x8 through)

3.54" (90 mm)

1" (25.4 mm) diameter

4.6" (116.8 mm)

Document 800-03542 Rev A

12/08 3

Figure 6 Ceiling Mount Dimensions

3Install the Housing

1. If not already done, route the field wiring:

a. Through the housing mount, then

b. Through the field wiring access hole in the housing, and then

c. Through the field wiring access hole under the base plate (see

Figure 7).

Note The wiring must extend at least one foot (0.3 m) past the

mount for wiring purposes.

2. Install the housing on the mount. Make sure there is Teflon®tape on

the threaded nipple part of the housing.

14.76” (375.0 mm)

5.51” (140.0 mm)

PF 1.5”

3.58" (91.0 mm) 4.57” (116.0 mm)

0.47” (12.0 mm)

diameter

3.54” (90 mm)

4Install and Adjust the Camera Position

Single Ball Joint Stick Mount (HDH4D)

1. Screw the camera onto the 1/4”-20

tripod mounting screw. Keep the

nut on the inside, closest to the ball

socket.

2. Loosen the position screws on the

base plate. See Figure 7.

3. Slide the camera mount in the slot

to position the camera based on the

installation requirements.

4. Tighten the position screws on the

base plate.

5. Loosen the base of the ball socket.

Adjust the camera to the required

angle.

6. Turn the base of the ball socket to tighten and secure the camera

angle.

7. Tighten the camera mounting nut tight against the fixed camera block.

8. Complete the wiring as per the camera selected.

Figure 7 Internal Pendant Housing - Single Ball Joint

Camera mount screw and nut

Ball socket base

Field wiring

access hole

Clip lower dome

lanyard to bracket

Position screws

(1 of 2) in the

base plate

Loosen ball socket base to

adjust camera angle

Camera mount screw

(1/4“-20 tripod) and nut

Base plate slot (1 of 2)

ACUIX Stick Mount Quick Installation Guide

Document 800-03542 – Rev A – 12/08

© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be

accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new

editions to this publication may be issued to incorporate such changes.

www.honeywellvideo.com

+1.800.796.CCTV (North America only)

[email protected]

Double Ball Joint Stick Mount (HDH6D)

Note See Figure 8 to complete this step.

1. Screw the camera onto the 1/4”-20 tripod mounting screw. The nut

cannot be loosened and stays on the inside, closest to the ball socket.

2. Grasp the bottom of the double pivot assembly and loosen it from the

base plate.

3. Slide the mount within the two slots to position the camera based on

the installation requirements.

4. Loosen the angle adjustment knobs. Adjust the camera to the required

angle.

5. Tighten all connections and complete the wiring as per the camera

selected.

Figure 8 Double Ball Joint

5Install the Lower Dome

1. Clip the lower dome lanyard to the housing bracket. See Figure 7.

2. Confirm that the o-ring is in place around the lower dome.

3. Press the lower dome into the housing and turn the screws to secure

the lower dome to the housing.

Camera mount

screw (1/4“-20

tripod)

Base plate slots -

bi-directional

Double ball joint assembly - loosen at

base to adjust camera location

Angle adjustment knob (1 of 2)

Andere Handbücher für ACUIX

Andere Honeywell Sicherheitskamera Handbücher

Honeywell

Honeywell HB75 Bedienungsanleitung

Honeywell

Honeywell HD4DIR Bedienungsanleitung

Honeywell

Honeywell HCCM474M Handbuch

Honeywell

Honeywell equIP Series S Bedienungsanleitung

Honeywell

Honeywell Performance HED1PR3 Bedienungsanleitung

Honeywell

Honeywell 30 Series Bedienungsanleitung

Honeywell

Honeywell HCC10 Bedienungsanleitung

Honeywell

Honeywell HD51 Bedienungsanleitung

Honeywell

Honeywell HD4VC4HRX Bedienungsanleitung

Honeywell

Honeywell ScanDome II HSDN-251NS/PS Betriebsanleitung

Honeywell

Honeywell HEW2PRW1 Bedienungsanleitung

Honeywell

Honeywell HD4CH Bedienungsanleitung

Honeywell

Honeywell NightHawk HCD82484 Bedienungsanleitung

Honeywell

Honeywell Vista VDC-350PIV-V Bedienungsanleitung

Honeywell

Honeywell ACUIX ES Bedienungsanleitung

Honeywell

Honeywell HCC474M Bedienungsanleitung

Honeywell

Honeywell HD60 Bedienungsanleitung

Honeywell

Honeywell EQUIP Series Bedienerhandbuch

Honeywell

Honeywell HCC484LX Bedienungsanleitung

Honeywell

Honeywell HD45IP Bedienungsanleitung

Honeywell

Honeywell HD8EXGCM18W Bedienungsanleitung

Honeywell

Honeywell HBD7S(X) Bedienungsanleitung

Honeywell

Honeywell iPCAM-WI Camera Bedienungsanleitung

Honeywell

Honeywell Lyric C1 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung