Honeywell H34S-IC Bedienungsanleitung

Document 800-16667 – Rev A – 01/2014

H34S-IC In-Ceiling Mount

Quick Installation Guide

This document describes how to install an equIP®Series H3D S Series indoor or H4D S Series

rugged IP minidome camera in a suspended ceiling using the H34S-IC in-ceiling mount.

CAUTION Installation and servicing should be performed only by

qualified and experienced technicians to conform to all local codes and

to maintain your warranty.

Package Contents

Before you begin, check that you have received all of the parts listed below. If any parts are

missing or damaged, contact your dealer immediately.

You will also need drilling tools and a Phillips screwdriver (not supplied).

In-Ceiling Mount Dimensions

• In-ceiling mount

• Trim ring

•Template

• Security Torx key

• Quick Installation Guide

3.23 in.

(82.1 mm)

Ø 7.87 in.

(200 mm)

Ø 4.53 in.

(115 mm)

Ø 1.73 in.

(44 mm)

Ø 5.91 in.

(150 mm)

60°

1.34 in.

(34 mm)

2 | H34S-IC In-Ceiling Mount Quick Installation Guide

www.honeywell.com/security

Preparing the Camera

1. Loosen the two captive security screws on the dome cover using the supplied Torx key

and remove the dome cover from the camera base.

2. Remove the inner cover from the camera assembly. Press both sides of the inner cover to

release it from the camera assembly.

3. Remove the screw securing the camera assembly to the camera base using a Phillips

screwdriver (not supplied).

4. Remove the camera assembly from the camera base by pressing the tabs on the sides of

the camera assembly. Store the camera assembly in the product box while you attach the

camera base to the in-ceiling mount.

Note For rugged cameras only: There are two cable entry holes on the camera base. Install

the conduit plug in the hole you are not using.

Indoor Dome Rugged Dome

800-16667 - A - 01/2014

| 3

Attaching the Camera to the In-Ceiling Mount

1. Align the three captive M3 screws on the in-ceiling mount with the mating screw holes on

the camera base. Make sure the cable entry hole on the in-ceiling mount is lined up with

the cable entry hole on the camera base.

2. Tighten the screws on the in-ceiling mount to secure it to the camera base.

Preparing the Ceiling

1. Select the location where you want to install the camera. The installation area must be able

to safely support the weight of the camera.

2. Place the adhesive-backed template on the ceiling at the selected location and then cut

around it (176 mm diameter).

Installing the Camera in the Ceiling

1. Run the camera wiring (power, network, video,

audio, alarm) through the camera base.

2. Insert the in-ceiling mount and attached camera

base into the ceiling hole, and then tighten the

screws on the in-ceiling mount until the camera

base is flush against the ceiling tile.

CAUTION Do not overtighten the

screws. Overtightening can damage the

in-ceiling mount. If using a power tool, set the

slip clutch to the lowest setting.

3. Retrieve the camera assembly from the product box, line up the tabs on the camera

assembly with the guides on the camera base, and then slide the camera assembly onto

the camera base until the tabs lock securely in place.

4. If you want, insert a microSDHC memory card (up to 32 GB, Class 10) into the

microSDHC card slot on the camera assembly.

Top View Side View

Bottom View (Indoor Dome)

www.honeywell.com/security

+1 800 323 4576 (North America only)

https://www.honeywellsystems.com/ss/techsupp/index.html

permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot

assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change

without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

Document 800-16667 – Rev A – 01/2014

5. Connect the camera wiring. Refer to the quick installation guide that came with the camera

for details.

6. Access the camera’s browser-based viewer (Honeywell Viewer) to view images, or,

alternatively, connect a coaxial cable from a portable service monitor to the BNC

connector on the camera control board.

7. Adjust the pan and tilt setting of the camera as desired. Loosen the locking screw on

the camera assembly gimbal to adjust the tilt angle and then retighten it. The tilt angle

is adjustable between –10° and 90°. The pan adjustment range is nearly 360° and the

rotation angle range is nearly 270°.

8. If you connected a coaxial cable to the camera in

step 5, remove it.

9. Replace the inner cover on the camera assembly.

10. Reinstall the screw securing the camera

assembly to the camera base.

11. Replace the dome cover on the camera base.

12. Tighten the two captive security screws on the

dome cover using the supplied Torx key.

13. Align the three holes in the trim ring with the

retaining nut on the in-ceiling mount, and then

snap the trim ring in place to complete the

installation.

Inhaltsverzeichnis

Andere Honeywell Sicherheitskamera Handbücher

Honeywell

Honeywell HD6 Series Bedienungsanleitung

Honeywell

Honeywell HBD92SX Bedienungsanleitung

Honeywell

Honeywell HD4DIR Bedienungsanleitung

Honeywell

Honeywell OptiCAM-IR Montageanleitung

Honeywell

Honeywell 60 Series Bedienungsanleitung

Honeywell

Honeywell EQUIP HD3MDIP Bedienungsanleitung

Honeywell

Honeywell HD4VC4HRX Bedienungsanleitung

Honeywell

Honeywell HB73 Bedienungsanleitung

Honeywell

Honeywell H2W2PRV3 Bedienungsanleitung

Honeywell

Honeywell H4W2PER2 Bedienungsanleitung

Honeywell

Honeywell GC-715N24 Bedienungsanleitung

Honeywell

Honeywell HD4U Bedienungsanleitung

Honeywell

Honeywell HD3DH Bedienungsanleitung

Honeywell

Honeywell HISD-2201WE-IR Bedienungsanleitung

Honeywell

Honeywell HD5 Series Bedienungsanleitung

Honeywell

Honeywell 4 Inch Dome Camera Bedienungsanleitung

Honeywell

Honeywell 30 Series Bedienungsanleitung

Honeywell

Honeywell 2450Cm Series Bedienungsanleitung

Honeywell

Honeywell H2D2PR1 Bedienungsanleitung

Honeywell

Honeywell EQUIP HD3MDIHX Bedienungsanleitung

Honeywell

Honeywell H4L6GR2 Bedienungsanleitung

Honeywell

Honeywell HDZ Series Bedienungsanleitung

Honeywell

Honeywell HD4CH Bedienungsanleitung

Honeywell

Honeywell EQUIP HD4DIP Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung