Honeywell Ultrak CSC100 U Series Bedienungsanleitung

Rev. A CSMU000835

09/15/03

CSC100xU Series

CSC110xU Series

Covert Cameras

USER MANUAL

All manuals and user guides at all-guides.com

all-guides.com

Rev. A ii CSMU000835

09/15/03

Rev. Date Description

A September 2003

Initial Release.

HONEYWELL VIDEO SYSTEMS

1305 WATERS RIDGE DRIVE

LEWISVILLE, TX 75057

(800) 796-CCTV

BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM HONEYWELL VIDEO

SYSTEMS.

THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL

RESPECTS. HOWEVER, HONEYWELL VIDEO SYSTEMS CANNOT ASSUME

RESPONSIBILITY FOR ANY CONSEQUENCES RESULTING FROM THE USE THEREOF.

THE INFORMATION CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT

NOTICE. REVISIONS OR NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO

INCORPORATE SUCH CHANGES.

All manuals and user guides at all-guides.com

Rev. A iii CSMU000835

09/15/03

WARNING

•TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol within an

equilateral triangle is intended to alert the user to the presence

of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instruction in the literature

accompanying the product.

All manuals and user guides at all-guides.com

Rev. A iv CSMU000835

09/15/03

TABLE OF CONTENTS

SECTION 1: INTRODUCTION ...................................................................... 1

1.1 PRODUCT DESCRIPTION.................................................................. 1

SECTION 2: INSTALLATION........................................................................ 2

2.1 BEFORE INSTALLING ....................................................................... 2

2.2 MOUNTING THE CAMERA............................................................... 2

Setting dip switches............................................................................... 5

2.3 WARM UP TIME ................................................................................. 5

2.4 WALK TESTING THE DETECTOR ................................................... 6

2.5 VOLTAGE REGULATION.................................................................. 6

SECTION 3: SPECIFICATIONS .................................................................... 7

USERS OF THE PRODUCT ARE RESPONSIBLE FOR CHECKING AND

COMPLYING WITH ALL FEDERAL STATE AND LOCAL LAWS AND

STATUTES CONCERNING THE MONITORING AND RECORDING OF

VIDEO AND AUDIO SIGNALS. HONEYWELL VIDEO SYSTEMS

SHALL NOT BE HELD RESPONSIBLE FOR THE USE OF THIS

PRODUCT IN VIOLATION OF CURRENT LAWS AND STATUTES.

All manuals and user guides at all-guides.com

Rev. A 1 CSMU000835

09/15/03

SECTION 1:

INTRODUCTION

1.1 PRODUCT DESCRIPTION

The CSC Series covert cameras are designed to blend into

commercial or office settings while providing superior

resolution and low-light capability. Built-in voltage

regulators prevent high voltage from reducing the life of the

camera.

The following models are covered in this manual:

CSC100BU

Covert Camera, Black & White

Standard Resolution,

Non-Functioning PIR

CSC100CU

Covert Camera, Color

Standard Resolution

Non-Functioning PIR

CSC110BU

Covert Camera, Black & White

Standard Resolution

Functioning PIR

CSC110CU

Covert Camera, Color

Standard Resolution

Functioning PIR

All manuals and user guides at all-guides.com

Rev. A 2 CSMU000835

09/15/03

SECTION 2:

INSTALLATION

2.1 BEFORE INSTALLING

Select a suitable location for the camera and enclosure.

•Select a location where an intruder is most likely to

cross the range of the detector.

•Do not place the camera in front of windows subject to

direct sunlight.

•Avoid locations which come in direct contact with

radiators, heating/cooling ducts, air conditioners, or

drafts.

•Do not place the camera in front of bulky objects

where camera view will be impaired.

2.2 MOUNTING THE CAMERA

The camera can be mounted directly to a wall or with an

optional mounting bracket for greater maneuverability.

Contact your sales representative for information about

mounting brackets.

To mount the unit directly to a wall:

1. Open the housing by pressing the snap-fit at the bottom

of the unit and gently separating the front and back

sections while avoiding damage to the camera

connections. Do not touch the face of the PYRO

sensor.

2. Remove the electronics board (PCB) screw to access

the rear housing. Refer to Figure 1 or 2, depending on

camera model.

All manuals and user guides at all-guides.com

all-guides.com

Rev. A 3 CSMU000835

09/15/03

2.2 MOUNTING THE CAMERA, CONTINUED

PCB

Screw Block

Termina

CCD

Connector

GND

VIDEO

GND

+Vin

Figure 1: PCB Layout

(CSC100BU/CSC100CU)

Relay

Groundin

Jumper

Relay

DIP

Switches

LED

Indicator

CCD

Connector

PCB

Screw

Pyro

Sensor

Figure 2: PCB Layout

(CSC110BU/CSC110CU)

All manuals and user guides at all-guides.com

Rev. A 4 CSMU000835

09/15/03

2.2 MOUNTING THE CAMERA, CONTINUED

3. Use the provided knockouts to assist in mounting the

unit. Use the side knockouts to mount the camera at an

angle.

Knock-

outs

Figure 3: Rear Housing Knockouts

4. Reattach the electronics board to the rear housing,

making final wiring additions if needed.

All manuals and user guides at all-guides.com

Rev. A 5 CSMU000835

09/15/03

2.2 MOUNTING THE CAMERA, CONTINUED

Setting dip

switches

5. Several operation options and modes are selectable via

DIP switches. (Models CSC110BU/CSC110CU only.)

Option Description

Pulse Counter Controls the amount of pulses (either

1 or 3 pulse mode) that need to be

detected before the detector activates.

LED Indicator Lights LED when movement is

detected. Only disable the LED

indicator after successfully walk

testing the detector.

Relay Operation Selectable to Normally Open (N.O.)

or Normally Closed (N.C.). If one

side of relay grounding is required,

install the relay grounding jumper as

JP1.

Set the switches using the following information:

Option Sw ON OFF

Pulse Counter 1 3 Pulse Mode 1 Pulse Mode

LED Indicator 2 LED ON LED OFF

Relay Operation 3 Relay N.C. Relay N.O.

6. Attach the front cover.

7. Connect the unit to a UL listed power supply or Ultrak

observation system.

2.3 WARM UP TIME

The detector will warm up for the first 90 seconds after

applying power.

All manuals and user guides at all-guides.com

Rev. A 6 CSMU000835

09/15/03

2.4 WALK TESTING THE DETECTOR

A walk test is used to determine the lens coverage pattern

of the detector and should be performed weekly.

1. Walk across the scope of the detector according to the

detection pattern selected. Since the pattern is

determined by the lens used in the detector, refer to the

lens range diagram.

2. Confirm that the LED activates, then deactivates after 2

motion-free seconds.

NOTE:

Camera view is wider than

PIR coverage pattern.

Figure 4: Rear Housing Knockouts

2.5 VOLTAGE REGULATION

The detector includes an on-board voltage regulator;

no external voltage regulation is necessary.

All manuals and user guides at all-guides.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Sicherheitskamera Handbücher

Honeywell

Honeywell HCC474M Bedienungsanleitung

Honeywell

Honeywell Performance HD251H Bedienungsanleitung

Honeywell

Honeywell HZC-855NX Series Bedienungsanleitung

Honeywell

Honeywell HCD545X Bedienungsanleitung

Honeywell

Honeywell HD3UX Bedienungsanleitung

Honeywell

Honeywell HD61 Series Bedienungsanleitung

Honeywell

Honeywell HQA HB276HD2 Bedienungsanleitung

Honeywell

Honeywell HEGS5300 Bedienungsanleitung

Honeywell

Honeywell HD4DIR Bedienungsanleitung

Honeywell

Honeywell 30 Series Bedienungsanleitung

Honeywell

Honeywell HDZ Series Bedienungsanleitung

Honeywell

Honeywell HCS544 Bedienungsanleitung

Honeywell

Honeywell 30 Series Bedienungsanleitung

Honeywell

Honeywell HD4U Bedienungsanleitung

Honeywell

Honeywell GC-715N24 Bedienungsanleitung

Honeywell

Honeywell HDZ302DIN Bedienungsanleitung

Honeywell

Honeywell HD40 Bedienungsanleitung

Honeywell

Honeywell HD3VC4HR Bedienungsanleitung

Honeywell

Honeywell HCC334L Bedienungsanleitung

Honeywell

Honeywell VSD-361P Bedienungsanleitung

Honeywell

Honeywell Performance H4D3PRV2 Bedienungsanleitung

Honeywell

Honeywell equip acuix Bedienungsanleitung

Honeywell

Honeywell HWC-D101 Bedienungsanleitung

Honeywell

Honeywell HCX3W Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung