Honeywell LYNXRPK-2 - Wireless Self-Contained Security Syste - LYNXRPK-2 - Wireless Self-Contained Security... Montageanleitung

LYNXR-2 Series

Security Systems

Installation and Setup Guide

ARMED READY

BYPASS

NO DELAY

RECORD

TEST

FUNCTION

STATUS

VOLUME PLAY

CODE

LIGHTS ON

LIGHTS OFF CHIME

ESCAPE

ADD

DELETE

SELECT

OFF 123

AWAY 45

AUX

STAY

789

K15011 7/08 Rev. A

- 2 -

RECOMMENDATIONS FOR PROPER PROTECTION

The Following Recommendations for the Location of Fire and Burglary Detection Devices Help

Provide Proper Coverage for the Protected Premises.

Recommendations for Smoke and Heat Detectors

With regard to the number and placement of smoke/heat detectors, we subscribe to the

recommendations contained in the National Fire Protection Association's (NFPA) Standard #72

noted below.

•Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and

areas of the household as follows: For minimum protection a smoke detector should be installed outside of each

separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The

installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally

recommended.

•For additional protection the NFPA recommends that you install heat or smoke detectors in the living room,

dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and

attached garages.

In addition, we recommend the following:

•Install a smoke detector inside every bedroom where a smoker sleeps.

•Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely

closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the

sleeper if the door is closed.

•Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air

conditioners or humidifiers) are used.

•Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.

•Install smoke detectors in any room where an alarm control is located, or in any room where alarm control

connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could

prevent the control from reporting a fire or an intrusion.

THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE

SOUNDING OF FIRE NOTIFICATION APPLIANCES.

DINING KITCHEN

BEDROOM

Smoke Detectors for Minimum Protection

Smoke Detectors for Additional Protection

Heat-Activated Detectors

BEDROOMBEDROOM

BEDROOM

LIVING

ROOM

TV ROOM DINING

LIVING ROOM

BASEMENT

BEDROOMBEDROOM

BEDROOM

CLOSED

DOOR

GARAGE

KTCHN

KITCHEN

BEDROOM

01000-002-V0

Recommendations For Proper Intrusion Protection

•For proper intrusion coverage, sensors should be located at every possible point of entry to a home or

premises. This would include any skylights that may be present, and the upper windows in a multi-level

building.

•In addition, we recommend that radio backup be used in a security system. This will ensure that alarm

signals can be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm

signals are normally sent over the phone lines, if connected to an alarm monitoring station).

-3-

Table of Contents

SYSTEM FEATURES ..................................................................................................................................5

MOUNTING THE CONTROL.....................................................................................................................6

WIRING CONNECTIONS...........................................................................................................................7

CONNECTING/CONFIGURING COMMUNICATIONS DEVICES ........................................................9

AC POWER AND BACKUP BATTERY....................................................................................................12

INSTALLING WIRELESS ZONES...........................................................................................................14

MECHANICS OF PROGRAMMING ........................................................................................................17

ZONE RESPONSE TYPE DEFINITIONS ...............................................................................................19

DATA FIELD DESCRIPTIONS ................................................................................................................21

✻56 ENHANCED ZONE PROGRAMMING MODE ................................................................................37

✻80 DEVICE PROGRAMMING MENU MODE ......................................................................................41

✻81 ZONE LIST MENU MODE................................................................................................................45

✻83 ENHANCED SEQUENTIAL MODE ................................................................................................47

✻84 ASSIGN ZONE VOICE DESCRIPTORS ..........................................................................................50

✻85 RECORD CUSTOM VOICE DESCRIPTORS...................................................................................52

REMOTE PROGRAMMING/CONTROL (DOWNLOADING) ................................................................53

SYSTEM OPERATION..............................................................................................................................55

KEYPAD FUNCTION SUMMARY...........................................................................................................60

TESTING THE SYSTEM ..........................................................................................................................61

SYSTEM COMMUNICATION ..................................................................................................................62

TROUBLESHOOTING GUIDE ................................................................................................................65

PROGRAMMING DEFAULT TABLES....................................................................................................68

LYNXR-2 CONTROL DEFAULTS .....................................................................................................68

LYNXR-2SIA CONTROL DEFAULTS...............................................................................................70

REGULATORY AGENCY STATEMENTS ..............................................................................................74

LIMITATIONS OF THIS SYSTEM STATEMENT..................................................................................75

UL NOTICES..............................................................................................................................................76

SIA QUICK REFERENCE GUDE ............................................................................................................76

CONTACTING TECHNICAL SUPPORT.................................................................................................77

INDEX.........................................................................................................................................................83

SPECIFICATIONS.....................................................................................................................................86

SUMMARY OF CONNECTIONS DIAGRAM ..........................................................................................87

- 4 -

LYNXR-2 Series Installation and Setup Guide

- 5 -

System Features

ULUL

LYNXR-2 Series is not intended for UL985 Household Fire applications unless a 24-hour backup battery

(P/N LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.

Powerline Carrier Devices have not been evaluated by UL.

The LYNXR-2 Series control is a self-contained, rechargeable wireless control/communicator that features

easy installation and usage. A built-in speaker provides voice annunciation of system status along with voice

descriptors of each zone. An internal module (if provided) allows the LYNXR-2 Series to communicate with

the Central Station via the Internet. The following illustration highlights the main features of this system.

ARMED READY

BYPASS

NO DELAY

RECORD

TEST

FUNCTION

STATUS

VOLUME PLAY

CODE

LIGHTS ON

LIGHTS OFF CHIME

ESCAPE

ADD

DELETE

SELECT

OFF

123

AWAY

AUX

STAY

789

ZONES and DEVICES

•Up to 24 wireless zones

(5800 Series transmitters)

•Up to 16 wireless button zones

•Up to 8 powerline carrier devices

•Supports wireless keypads

8 USER CODES

•Installer code

•Master code

•5 Secondary codes

•Duress code

•3 Panic functions

ALARM OUTPUT

•Built-in sounder

•Piezo output

(30mA max.)

•Bell output

(120mA max.)

•Steady output for

burglary/panic

•Temporal pulse

output for fire alarms

•Long range

radio/audio alarm

verification

PROGRAMMING

•Options stored in EEROM

•Can be uploaded, downloaded or

controlled via IBM-compatible

computer using Compass

downloader software and specified

HAYES modem or via capable GSM

or IP communications module

•Voice prompt programming mode

COMMUNICATION

•Ademco Low Speed

•Sescoa/Radionics

•Ademco Express

•Ademco Contact ID

•Paging feature

•Internet central station

communication

•GSM cellular central

station communication

SYSTEM POWER

•Primary Power: Ademco K10145X10

plug-in transformer, 110VAC to

9VAC, 25VA output (K10145CN in

Canada)

•Backup battery: Rechargeable

nickel-metal hydride battery pack

rated at 7.7Vdc.

FEATURES

•Real-time clock display and Fixed-Word display

•Message center (for user recorded messages)

•Voice announcement of system and zone status

•Voice chime

•Alarm clock

•Reminder

•X10 scheduling

•Latch key reports

•Automatic stay arming

•Remote phone control

•“Follow me” reminder and system Announcements

OTHER FEATURES

•Exit error feature (detects difference between an

actual alarm and exit alarm caused by leaving a door

open after the exit delay expires)

•Event log stores up to 84 events

•Macro/ 1-button paging

•RF jam detection

•Remote phone control

•Compatible with encrypted (high-security) devices

SPECIAL FEATURES

•Two-way voice communication

•Speaker phone operation

•Supports AlarmNet remote

services

LYNXR-2 Series Installation and Setup Guide

- 6 -

Mounting the Control

Wall Mounting

The illustration below shows the front assembly separated from the back plate.

DO NOT disconnect the ribbon cable from the terminal strip board. Disconnect the cable only from the

front assembly board.

1. Release the front assembly from the back

plate by depressing the two locking tabs

at the top of the unit with the blade of a

medium size screwdriver.

2. Once these tabs have been released,

insert the screwdriver in the side of the

case and release the side locking tabs by

gently twisting.

3. Carefully disconnect the ribbon cable from

the front assembly, leaving the ribbon

cable connected to the terminal block

PC board. The back plate contains the

terminal block for making wiring

connections.

4. Mount the back plate to a sturdy wall,

feeding the field wiring through the

appropriate openings in the back plate.

5. After wiring connections are made,

carefully reconnect the ribbon cable to

the front assembly PC board connector

(properly aligning the red wire).

6. Snap the front assembly to the back plate

so it is secured by the locking tabs.

LOCKING TABS

RED WIRE

MARKING

DISCONNECT

THIS END ONLY!

09012-002-V0

LOCKING

TABS

LOCKING

TABS

Desktop Mounting

For desktop use the optional mounting base (model LYNX-DM, purchased separately) must be used.

1. Slide the control panel onto the mounting

base locking tabs.

2. Bring all wiring through the bottom of the

mounting base, using one of the three

wire entry locations, before making

connections to the control panel.

3. Use tie-wraps to secure the wiring to the

built-in wire loops as needed. Use the two

supplied screws to secure the control

panel to the mounting base.

09015-002-V0

ARMED READY

BYPASS

NO DELAY

RECORD

TEST

FUNCTION

STATUS

VOLUME PLAY

CODE

LIGHTS ON

LIGHTS OFF CHIME

ESCAPE

ADD

DELETE

SELECT

OFF

123

AWAY

AUX

STAY

789

WIRE ENTRY

KNOCKOUT

(1 of 3)

LYNXR-2 Series Installation and Setup Guide

- 7 -

Wiring Connections

Wiring Overview

The following summarizes the connections required. Refer to the Wiring Connections paragraph and the

Summary of Connections diagram on the inside back cover when making connections.

ULUL

External sounders have not been evaluated by UL.

09012-009-V0

SUPER HIGH-CAPACITY

BATTERY CONNECTOR

TERMINAL

STRIP

TELEPHONE

CONNECTIONS

LRR/IP

COMMUNICATIONS

PORT

GSML/GSMVL

COMMUNICATIONS

PORT

LOCAL

SOUNDER

DISABLE

STANDARD

HIGH-CAPACITY

BATTERY CONNECTOR

Wiring Connections

1. Make Earth Ground Connection - The designated earth ground terminal (1) must be terminated in a good earth ground

for the lightning transient protective devices in this product to be effective. The following are examples of good earth

grounds available at most installations:

Metal Cold Water Pipe - Secure a non-corrosive metal strap (copper is recommended) to the pipe that is electrically

connected and secured to which the ground lead is electrically connected and secured.

AC Power Outlet Ground - Available from 3-prong, 120VAC power outlets only. To test the integrity of the ground

terminal, use a three-wire circuit tester with neon lamp indicators, such as the UL Listed Ideal Model 61–035, or

equivalent, available at most electrical supply stores.

a. Connect terminal 1 to a good earth ground.

2. Make Phone Line Connections - For local or full line seizure follow the appropriate steps below.

Local Seizure

a. Connect the incoming phone line to either the 8-position jack or terminals 2 (TIP) and 3 (RING) on the Lynx.

b. Connect the handset phone lines to either the RJ11 jack or terminals 4 (TIP) and 5 (RING).

Full Line Seizure: The control must be placed in series with the incoming phone line. Plugging the Direct Connect Cord

directly into the RJ31X jack, allows the control to seize the phone line when an alarm occurs and normal phone line

usage by the premises phones if the plug needs to be removed.

c. Cut the incoming RING and TIP phone lines (typically red and green, respectively) and connect them to RJ31X

terminals 4 (red) and 5 (green).

d. Connect the premises end of the cut RING and TIP wires to RJ31X terminals 1 (grey) and 8 (brown) respectively.

e. Wire the flying leads of a Direct Connect Cord to the control’s phone terminals as shown in the diagram or plug into

the 8-position jack.

f. Plug the Direct Connect Cord into the RJ31X jack.

LYNXR-2 Series Installation and Setup Guide

- 8 -

Wiring Connections

RJ31X

RING

TIP

INCOMING

PHONE LINE

PREMISES PHONES

TIP RING TIP RING

BROWN

GREY

RED

GREEN

INCOMING

PHONE LINE

PREMISES

PHONES

}

GREENRED

GREY BROWN

RING

TIP

DIRECT

CONNECT

CORD

8-POSITION

JACK

01000-008-V0

Full Line Seizure Connections

ULUL

Do not remove the local sounder shorting jumper (shunt).

External sounders and powerline carrier devices have not been evaluated by UL

LOCAL SOUNDER DISABLE: The Master Keypad’s built-in piezo sounder can be disabled by removing the

shorting jumper (shunt) on the terminal board. If disabled, however, no sounding will occur upon AC loss,

since the external sounder does not operate when AC power is lost.

3. Make External Sounder Connections - The control panel supports either a 6-14VDC piezo sounder (30mA max.) or

6-14VDC bell (120mA max.; e.g. ADEMCO WAVE2EX).

a. Connect a piezo sounder to terminals 10 (+) and 11 (–); OR a bell to terminals 11 (–) and 12 (+).

4. Disable Local Sounder Option - If required the Master Keypad’s built-in piezo sounder can be disabled.

a. Remove the shorting jumper (shunt) on the terminal board.

5. Make Powerline Carrier Device Connections - The control panel supports up to 8 Powerline Carrier Devices. If using

these devices, they must be connected to the K10145X10 transformer, as shown in the SUMMARY OF

CONNECTIONS diagram.

a. Connect the com/data/sync/ lines from the transformer to terminals 9, 13, and 14, respectively.

If not using the supplied connection cable, you may need to reverse the black and yellow wire connections.

Refer to the ✻

✻✻

✻80 Device Programming Menu Mode section for details on programming Powerline Carrier

Devices.

LYNXR-2 Series Installation and Setup Guide

- 9 -

Connecting/Configuring Communication Modules

General

This LYNXR-2 Series supports central station reporting via the internet using wireless (GSM) and hardwire

(IP) communications modules. It also supports upload/download programming capability via the Internet or

a Private local area network (Intranet). This allows site maintenance independent of central station

monitoring, and modification to sites globally via the Internet or through a private LAN. Refer to the

instructions provided with the LRR/IP Communications Device being installed for additional information

regarding its installation, programming, and registration.

LYNXR-2 Series does not support the 7845i-ENT remote access feature.

Connecting Long Range Radio and Internet Communication Devices

Connect and configure the communications device as follows (refer to the Installation Instructions for device

that you are installing for additional information):

The wire run between the LYNXR-2 Series and the Communications Device must not exceed ten (10) feet.

ULUL

The 7845i-ENT has been evaluated by UL for Household Burglary installations but has not been evaluated

for Household Fire installations.

AlarmNet 7847i-L* Communications Device

1. Install the module into the LYNXR-2 Series back plate and secure it with the two provided screws. Refer to the diagrams

that follow.

2. Connect the provided ribbon cable between the module and the PC board. This cable provides DC power and ground for

the module and data in/data out connections.

3. Connect the device to the Internet via a cable/DSL modem and router or to an Intranet (LAN) via the appropriate Ethernet

connection.

* When available. The 7847i-L module has not been evaluated by UL.

SCREW (2)

09012-008-V1

CABLE

7720P

PROGRAMER

CONNECTION

RJ45

(FOR INTERNET CONNECTION)

LRR / IP

COMMUNICATION

PORT

Installing the 7847i-L Communications Module

LYNXR-2 Series Installation and Setup Guide

- 10 -

Connecting/Configuring Communication Modules

AlarmNet 7845GSM, 7845i-GSM*, 7845i-ENT, 7845i or 7847i-E* Communications Device

The 7845i-ENT and 7845i cannot be used for installations requiring 24-hour standby.

1. Connect the 4-wire communications cable to the LRR/IP Communications port on the LYNXR-2 Series.

2. Connect the four wires to the specific Communications device as shown in the accompanying figures.

3. If you are installing a 7845GSM or 7845i-GSM you must also install a jumper between terminals 2 and 3 on the

communications device.

4. Connect the device to the Internet via a cable/DSL modem and router or to an Intranet (LAN) via the appropriate Ethernet

connection, if applicable.

ULUL

AlarmNet 7845GSM and 7845i-GSM modules have not been evaluated by UL.

* When available

7845GSM /

7845i-GSM

LYNX

SUPER HIGH

CAPACITY

BATTERY

(OPTIONAL)

REQUIRED FOR

24-HR BACKUP

09012-018-V0

GND

Z3 OR DATA OUT

Z1/Z2 OR DATA IN

ECP (+) VOLTAGE INPUT

RED

BLK

GRN

YEL

RED

BLK

GRN

YEL

4-WIRE CABLE (N4632-4)

TB1

LRR/IP COMMUNICATIONS PORT

CONTROL PANEL

+12 VDC

GND

D ATA I N

DATA OUT

LYNX

STANDARD

CAPACITY

BATTERY

Connecting AlarmNet 7845GSM / 7845i-GSM

7845i-ENT / 7845i

09012-019-V0

GND

D ATA I N

DATA OUT

(+) VOLTAGE INPUT

TB 1

RED

BLK

GRN

YEL

RED

BLK

GRN

YEL

4-WIRE CABLE (N4632-4)

LRR/IP COMMUNICATIONS PORT

CONTROL PANEL

+12 VDC

GND

D ATA I N

DATA OUT

LYNX

STANDARD

CAPACITY

BATTERY

Connecting AlarmNet 7845i-ENT/7845i/7847i-E*

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Sicherheitssystem Handbücher

Honeywell

Honeywell LYNX Touch Security System Bedienungsanleitung

Honeywell

Honeywell LYNX Touch L7000 Series Bedienungsanleitung

Honeywell

Honeywell Ademco VISTA-32FB Betriebsanleitung

Honeywell

Honeywell ADEMCO VISTA-48A Montageanleitung

Honeywell

Honeywell FG8MS Bedienungsanleitung

Honeywell

Honeywell V4000 Montageanleitung

Honeywell

Honeywell Domonial Bedienungsanleitung

Honeywell

Honeywell ADEMCO LYNXRIEN-EA Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms ES-50XC Bedienungsanleitung

Honeywell

Honeywell Ademco VISTA-20PCN Betriebsanleitung

Honeywell

Honeywell Galaxy 3-48C Betriebsanleitung

Honeywell

Honeywell SEF8MS Bedienungsanleitung

Honeywell

Honeywell Domonial Bedienungsanleitung

Honeywell

Honeywell Galaxy 8 Bedienungsanleitung

Honeywell

Honeywell VISTA 21iPLTE Bedienungsanleitung

Honeywell

Honeywell NetAXS NX4S1 Bedienungsanleitung

Honeywell

Honeywell VISTA-21iP Bedienungsanleitung

Honeywell

Honeywell Ademco VISTA-50P Montageanleitung

Honeywell

Honeywell ADEMCO 4110XM Bedienungsanleitung

Honeywell

Honeywell DTPI8M Bedienungsanleitung

Honeywell

Honeywell Ademco VISTA-20P Betriebsanleitung

Honeywell

Honeywell VAM Bedienungsanleitung

Honeywell

Honeywell Notifier NFS2-640/E Bedienungsanleitung

Honeywell

Honeywell Domonial Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung