Honeywell Domonial Bedienungsanleitung
User Manual
2
Congratulations on your purchase of our DOMONIAL
security system.
This system is designed to operate on an authorised
radio frequency and will in no way endanger the user.
To make the best out of your DOMONIAL we advise
you to read this manual carefully. This manual has been
written for your special attention and integrates
remarks and suggestions of existing users.
You can write here the places of the detectors :
Channel 1 : Channel 11 :
Channel 2 : Channel 12 :
Channel 3 : Channel 13 :
Channel 4 : Channel 14 :
Channel 5 : Channel 15 :
Channel 6 : Channel 16 :
Channel 7 : Channel 17 :
Channel 8 : Channel 18 :
Channel 9 : Channel 19 :
Channel 10 : Channel 20 :
TABLE OF CONTENTS
①
Introduction to your security system 4
②
Understand the audible acknowledgements 6
③
How to use your keyfob ? 9
④
How to use your wireless keypad ? 12
⑤
Detectors operating principle 16
⑥
How to manage your system 17
via a telephone ?
⑦
Maintenance and recommendations 19
3
0
1
23
456
89
7
SOS
0
1
23
456
89
7
SOS
4
Introduction to your security system
The DOMONIAL control panel/communicator unit is the brain of your security system. It
exchanges information with the associated wireless peripherals. DOMONIAL centralises the data
sent by the detectors, records the arming and disarming operations and communicates with
your central monitoring station.
SPECIFICATIONS
Radio
●
Narrow band frequency modulation
●
Identification code specific to each
component (no possible interference
between neighbouring systems)
●
Protection against attempted jamming
●
Radio monitoring of the system
detectors and sounders
Electrical
●
230V mains with battery backup
●
Built-in voltage surge protection
●
System supply monitoring
Transmission
●
Built-in telephone transmission
●
Telephone line loss detection
●
Transmission monitoring by periodical tests (as programmed)
Operational
●
3 protected area groups - 20 detection points
●
Alert functions, with sounder or silent
●
All door and window contacts closed position
checked upon arming
●
Control panel tamper protection against opening
●
Audio verification
①
1- LED INDICATOR “AC MAINS POWER”
ON : The Control Panel is supplied by the Mains power
OFF : There is a Mains Power Failure – The Control Panel is supplied by its built – in battery
2- LED INDICATOR “SYSTEM ARMED”
ON : The system is totally armed
OFF : The system is disarmed
BLINKING : The system is Part Armed
3- LED INDICATOR “OPENED DETECTOR FAULT”
BLINKING : It means that one of the window or door protected by a magnetic contact is
opened. It blinks until the window or door get closed
4- LED INDICATOR “ALARM MEMORY”
ON : It means that an alarm occurred during the ARMING mode
BLINKING : It means that an alarm occurred during the Part arm mode
The indicator remains ON until the next arming
5- LED INDICATOR “TECHNICAL FAULT”
ON : It indicates a fault on a technical channel
BLINKING : It indicates a fault on the system ( Battery fault, Supervision, Tamper, Phone line
failure or Radio Jamming )
The indicator remain ON or BLINKING until the End of the technical or system fault
The front cover of the control panel
features LEDS indicators which show
the status of your security system.
Light indicator
5
Understand the audible acknowledgements
SIGNALLING EQUIPMENT
The sounder, whether it is built in the control panel 1 or mounted in the house 2 is an effective
deterrent thanks to its power and very aggressive loudness.
Both these components emit an audible confirmation of your arming and disarming the security
system. The sound volume can be adjusted by the installer.
6
1
2
②
7
ARMING
confirmation
DISARMING
confirmation
PART or
ANNEX
zone arming
confirmation
FAULT signal
ALERT
confirmation
Exit delay
confirmation
Sequence of 3 modulated sounds
Duration : 4 seconds
When Arming, confirms that the control
panel has received the information.
When Disarming, confirms that the
control panel has received the
information.
This confirmation indicates
Part arming of the security system
This signal corresponds to a fault in the
system
Confirms the transmission of an alert to
your central monitoring station
After Arming, this is the Exit delay
count down (programmable option)
Long and continuous beep
Duration : 2,5 seconds
Sequence of 2 modulated sounds
Duration : 2,5 seconds
2 times 7 fast beeps
4 beeps in case of alert...
sent via the keypad
10 sec. before actual arming...
one beep every second
AUDIBLE CONFIRMATIONS OF YOUR ACTIONS
Built-in audio verification version
DOMONIAL can have a built-in audio verification function, allowing you to call and talk to the
persons who are in the monitoring station, just by pressing the button. Then the monitoring station
will ask you to talk.
8
9
How to use your keyfob ?
The keyfob is used to arm, totally or partly, and disarm your security system as well as to
trigger an audible or silent alert.
CHARACTERISTICS
●
Power requirement: one 3V lithium CR 1/3 type battery
●
Weight: 30 grs
OPERATION
●ARMING
✔ Press key :
✔ The indicator light on the keyfob comes on briefly when you release
the button
-
An audible confirmation
is simultaneously emitted by all the signalling equipments.
Always make sure that your arming the system is followed by the audible confirmation. Your
house will be under effective protection about 2 minutes after you have armed the system.
Arming can be controlled from inside the house or from outside, in the immediate vicinity.
If, upon arming, a door or window contact is in the "open" position (e.g. window not properly
shut), a FAULT signal will inform you. Disarm the system, shut the corresponding window
and repeat arming.
●DISARMING
✔ Press key :
✔ The indicator light on the keyfob comes on briefly when you release the button.
③
-
The audible confirmation is emitted by the
signalling equipment.
Action on the key immediately disarms the security system of your house.
●PARTIALARMING
Provided that this function has been programmed by the installer, you can choose to protect
only a part of your house while you are in the other part. For instance, you can protect the
ground floor while your are sleeping upstairs.
✔ Press key
✔ The indicator light on the keyfob comes on when you release the button.
-
The audible confirmation is simultaneously
emitted by the signalling equipment.
Part protection becomes effective about 2 minutes after you have armed it. Any intruder in the
protected zone will trigger an alarm. Part protection is disarmed by action on the key.
●ALERT FUNCTION
This key enables you to send an instant alarm if you need urgent assistance at home.
✔ Push simultaneously the 2 “SOS” keys during 2 secondes
✔ The indicator light comes on.
10
+
Andere Handbücher für Domonial
6
Inhaltsverzeichnis
Andere Honeywell Sicherheitssystem Handbücher
Honeywell
Honeywell VISTA-128FBP Bedienungsanleitung
Honeywell
Honeywell First Alert FA168CPS Bedienungsanleitung
Honeywell
Honeywell 013002 Bedienungsanleitung
Honeywell
Honeywell TCPA2B Bedienungsanleitung
Honeywell
Honeywell ADEMCO LYNXR Series Bedienungsanleitung
Honeywell
Honeywell Gamewell-FCI E3 Series Bedienungsanleitung
Honeywell
Honeywell Home SI800MS Bedienungsanleitung
Honeywell
Honeywell Lynx Plus Series Bedienungsanleitung
Honeywell
Honeywell LYNX Bedienungsanleitung
Honeywell
Honeywell Galaxy 8 Bedienungsanleitung
Honeywell
Honeywell LYNX Touch L5210 Series Bedienungsanleitung
Honeywell
Honeywell INTELLIGUARD 9000 Handbuch
Honeywell
Honeywell ADEMCO VISTA-40 Bedienungsanleitung
Honeywell
Honeywell Manning GM-1 Handbuch
Honeywell
Honeywell Le Sucre Bedienungsanleitung
Honeywell
Honeywell IS335 Bedienungsanleitung
Honeywell
Honeywell nfs2-3030 Bedienungsanleitung
Honeywell
Honeywell LYNX Touch 5100 Betriebsanleitung
Honeywell
Honeywell LYNX Bedienungsanleitung
Honeywell
Honeywell Friedland HISK1 Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung