Honeywell FAAST LT Bedienungsanleitung

Product Category

Technical Support

FAAST LT Auto Ultra Tuning Instructions

FA AST LT

Figure 1.

The FAAST LT aspirating smoke detectors are designed for reliable trouble-free

operation. However, if a FAAST LT with a production date before 2017 causes

frequent disturbances in the air ow, software check the ultrasonic air ow sensor

and remedy if necessary. Production date can be found on the device nameplate

lower right; the four numbers before the "T" signify (yywwT) j = year, w = week.

The software and its function can only be used on FAAST LT devices equipped with

rmware v3. This test software can not "x" or optimize faulty devices or congurations.

If necessary, copy the le "FAAST_LT_auto_ultra_tuning_v1.1.zip" to the desktop of your

computer, unzip it with the password "giotto" and rename the le from .ese to .exe.

Then please proceed as follows:

1) Turn on the FAAST LT unit and allow it to run in normal operation. Set the unit

to Technician / Maintenance mode (factory default 3111 password), open the

front door, and connect the FAAST LT unit to your computer via the USB cable.

2) Make sure that the pipe network congured with Pipe IQ and intended

for this detector is connected to the input / inputs of the device. With

open pipe connections, the program will give a wrong result.

3) Start the software "FAAST LT_auto_ultra_tuning_v1.1" The software

should automatically select the correct COM port. Click on "Connect".

4) Click on "ULTRASONIC TUNING". After about 3 minutes, the program calculates

three parameters (e.g. best settings 2,6,15), and proposes the best parameter (e.g.

"2") for selection. See Figure 1. to the right for an example; the program displays three

parameters (2,6,15) and at the same time indicates that the best selection is "2".

5) Click "OK" to conrm the value. A le log is stored with all the

data of the operation in the same folder of the program.

6) Click on "CANCEL" to cancel the change. A le log is created with all the data of the process.

7) Click "DISCONNECT" and restart the FAAST LT (power cut) to apply the new settings.

Please Note: If the program displays the values "4" or "15" in the selection window, this

means that a new adjustment of the airow sensor will have a negligible effect. In this

case, it is probably best to replace the device. The original factory setting is "15".

After adjusting the airow sensor, the FAAST LT should run for

some time in its typical operating environment. Should there be

any instability, it is recommended to replace the device.

Please contact your Representative if you have any questions.

www.faast-detection.com

All technical data is correct at the time of publication and is subject to changes without notice. All trademarks acknowledged. Installation information: In order to ensure full

functionality, refer to the installation instructions as supplied.

Diagnostics Functions

RESET DEVICE (2 seconds): same as the FAAST LT RESET button

RETRIEVE LOG (10 seconds): this will retrieve the entire

log and save it in a le on the desktop (assuming the

Diagnostic Tool is run from the desktop as suggested).

EXECUTE DIAGNOSTIC (variable time required):

This will retrieve all the information from the device and tests

various functions. Again, if the Diagnostic Tool is run from the

desktop, the results will be saved in a le on the desktop.

At the end, the Diagnostic will automatically

perform a RESET on the FAAST LT.

Please note:

• Running the Diagnostics will cause FAULT

relay activation during the tests.

• With TEST ALARMS selected, the program

will activate the alarm relays.

• With FULL DIAGNOSTIC selected, an

extended set of functions is checked.

• Return the Diagnostic data le to sse.technical@systemsensor.com

• Important- after using this program it is necessary

to restart the device by powering it OFF and ON again

after 10 seconds to restore normal behavior.

Time required for the diagnostic depends on the options selected:

FULL DIAGNOSTIC TEST ALARMS TIME REQUIRED

NO NO ~100sec

NO YES ~14 0sec

YES NO ~15min

YES YES ~17min

To stop the Diagnostics, click on the ABORT button

repeatedly until execution is stopped.

Please contact your Representative if you have any questions.

www.faast-detection.com

Inhaltsverzeichnis

Andere Honeywell Rauchmelder Handbücher

Honeywell

Honeywell IPGSM-DP Montageanleitung

Honeywell

Honeywell Fire-Lite Alarms Innovair flex D365PL Bedienungsanleitung

Honeywell

Honeywell Ademco 5806 W3 Betriebsanleitung

Honeywell

Honeywell SiX Series Bedienungsanleitung

Honeywell

Honeywell Notifier VESDA-E VEA Series Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell MS-5UD Series Bedienungsanleitung

Honeywell

Honeywell FMST FXV(E) Series Bedienungsanleitung

Honeywell

Honeywell TC842B1007 Bedienungsanleitung

Honeywell

Honeywell JTYJ-GD-01BW Bedienungsanleitung

Honeywell

Honeywell SiXSMOKE-CN Bedienungsanleitung

Honeywell

Honeywell Gamewell 1415 Bedienungsanleitung

Honeywell

Honeywell FCI 2151 Bedienungsanleitung

Honeywell

Honeywell TC846A1005 Bedienungsanleitung

Honeywell

Honeywell SS4-A2 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER FSP-951T-SELFT Bedienungsanleitung

Honeywell

Honeywell Notifier NBG-12LX Bedienungsanleitung

Honeywell

Honeywell X Series Bedienungsanleitung

Honeywell

Honeywell LT-200 MI-FL20 Series Bedienungsanleitung

Honeywell

Honeywell FIre LIte ALarms D350PL Bedienungsanleitung

Honeywell

Honeywell Notifier FSP-851 Bedienungsanleitung

Honeywell

Honeywell Notifier FDU-80 Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms BEAM355A Bedienungsanleitung

Honeywell

Honeywell 5193SD Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung