Honeywell FCI 2151 Bedienungsanleitung

2151

System Sensor

Low Profile, Photoelectronic

Plug-In Smoke Detector

Features

• Low-profile construction.

• Easy plug-in of the head to base.

• Tamper-resistant feature.

• Test Switch.

• 360°View angle of alarm LEDs.

• Compatible with FCI control panels.

• Audible sounder base (pptional).

• Field metering of detector sensitivity.

• Removable insect screen and cover for field

cleaning.

• Insect-resistant screening

(020"/.508 mm openings).

Description

The System Sensor 2151 low profile photoelectronic

smoke detector is specifically designed to meet the per-

formance requirements of fire detection/alarm systems.

The 2151 detector uses a state-of-the-art optical sensing

chamber and is designed so that LED failure will not

cause an alarm. The detector is designed to provide open

area detection, and when installed in a two-wire base, is

compatible with FCI fire alarm control panels. The detec-

tor’s operation and sensitivity can be tested in place.

The 2151 detector is of plug-in construction and plugs into

the same base as the 1151 ionization smoke detector,

making both models interchangeable. Bases are available

for two-wire, four-wire, and 120 VAC four-wire operation,

and also with an audible sounder.

Two visible LEDs on each detector flash approximately

every ten seconds indicating that power is being applied

to the detector. The LEDs light steadily when the detector

is in alarm. A remote LED annunciator is available as an

optional accessory.

The 2151 is UL Listed for mounting inside ducts up to a

velocity of 3,000 FPM.

Functional testing is performed by placing a test magnet

against the cover. The LED on the detector should light

within 30 seconds.

Field metering of detector sensitivity may be performed

with the aid of a voltmeter and Test Kit, Part No. MOD

400R.

Specifications

Sensitivity 3.0 %/ft. (nominal)

Operating voltage 8.5 - 35 VDC (24 VDC nominal)

Standby current 120 uA maximum

Operating

temperature

32°to 120°F (0°to 49°C)

Operating humidity 10 % - 93 % relative humidity

Air velocity 3,000 feet per minute maximum

Construction Off-white flame retardant plastic

Diameter 6.2 inches (15.5 cm) (flanged base)

Height 1.7 inches (4.2 cm)

Weight 3.6 oz. (104 g)

GAMEWELL-FCI

12 Clintonville Road, Northford, CT 06472 - Tel: (203) 484-7161 - Fax: (203) 484-7118

Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.

An ISO 9001-2000 Company

1151

Downloaded from Elcodis.com electronic components distributor

Ordering Information

Part Number Description

2151 Photoelectronic detector

B110LP Base, Two-wire

301BL4

Base, four-wire, 24 VDC operation

Form A & C

301BL4AC

Base, four-wire, 120 VAC operation

Form A, C & Supv.

B401BH

Base, four-wire, with audible

sounder

RA-400Z Remote alarm indicator

PAM-1 End of line relay, 24 VDC

Form B

Test Kit

Mounting

•On a 4-inch square box with or without plaster ring.

Minimum depth 1.5 inches.

•On a 3.5-inch octagonal box. Minimum depth 1.5

inches.

Installation

Place the detector into the detector base. Turn the detec-

tor clockwise until the detector locks into place.

To use the tamper-proof feature, break the smaller tab on

the scribed line in the tamper proof tab located on the

detector mounting bracket. Install the detector. To remove

the detector from the base when using the tamper-proof

feature, insert the blade of a small screwdriver into the

hole on the side of the base and push the plastic lever

away from the detector head. This will allow the detector

to be rotated counterclockwise for removal. NOTE: The

decorative ring must be removed in order to remove the

head when using the tamper-proof feature.

The tamper-proof feature may be defeated permanently

by breaking the plastic lever off the base.

Note: The number of two-wire smoke detectors which can

be accommodated per zone varies with different control

panels. Consult the control panel instruction manual to

determine the capacity.

Refer to NFPA 72, Chapter 5-3, “Smoke Sensing Fire

Detectors” for spacing, location of detectors and other

guidelines.

Testing

Detectors may be tested in the following ways:

•Place a test magnet against the detector as directed in

the installation instructions. The detector should go into

alarm within 30 seconds.

•Field metering of detector sensitivity may be per-

formed with the aid of a voltmeter and Test Kit,

MOD 400R.

For the complete procedure, refer to the Installation and

Maintenance instructions furnished with each detector.

Cleaning programs should be adapted to the individual

environment in conformance with NFPA Standard 72. We

recommend at least an annual cleaning of the unit. The

detector screen and cover assembly can be removed,

revealing the sensing chamber. A vacuum cleaner can be

used to remove dust from the screen, cover and sensing

chamber. For the complete procedure, refer to the Instal-

lation and Maintenance instructions furnished with each

detector.

Maintenance

GAMEWELL-FCI

12 Clintonville Road, Northford, CT 06472 - Tel: (203) 484-7161 - Fax: (203) 484-7118

www.gamewell-fci.com 9020-0583 Rev. B page 2 of 2

Downloaded from Elcodis.com electronic components distributor

Andere Honeywell Rauchmelder Handbücher

Honeywell

Honeywell GasAlert Extreme Bedienungsanleitung

Honeywell

Honeywell SiXCOMBO Bedienungsanleitung

Honeywell

Honeywell TC846A1005 Bedienungsanleitung

Honeywell

Honeywell MORLEY-IAS MI-LPB2-S2I Bedienungsanleitung

Honeywell

Honeywell Notifier FSP-851 Bedienungsanleitung

Honeywell

Honeywell 5800COMBO-CN Bedienungsanleitung

Honeywell

Honeywell compact asd Bedienungsanleitung

Honeywell

Honeywell HI-SPEC Bedienungsanleitung

Honeywell

Honeywell 5806W3 Montageanleitung

Honeywell

Honeywell Smoke Alarm Bedienungsanleitung

Honeywell

Honeywell JTYJ-GD-01BW Bedienungsanleitung

Honeywell

Honeywell Silent Knight SD505 Bedienungsanleitung

Honeywell

Honeywell FCI 2451 Series Bedienungsanleitung

Honeywell

Honeywell Fire-Lite Alarms BEAM355A Bedienungsanleitung

Honeywell

Honeywell 5193SD Bedienungsanleitung

Honeywell

Honeywell SiX Series Bedienungsanleitung

Honeywell

Honeywell D355PL Bedienungsanleitung

Honeywell

Honeywell 5800COMBO Bedienungsanleitung

Honeywell

Honeywell IPGSM-DP Montageanleitung

Honeywell

Honeywell Gamewell 7100 Series Montageanleitung

Honeywell

Honeywell SS4-AI Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell Velociti 3 Series Bedienungsanleitung

Honeywell

Honeywell NOTIFIER NFXI-ASD11 Kurzanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung