Honeywell 10260A Series Bedienungsanleitung

Inhaltsverzeichnis

Andere Honeywell Schalten Handbücher

Honeywell

Honeywell PLS730B Bedienungsanleitung

Honeywell

Honeywell 39342 Bedienungsanleitung

Honeywell

Honeywell NGC Series Bedienungsanleitung

Honeywell

Honeywell Limitless WGLA Series Bedienungsanleitung

Honeywell

Honeywell 39348 Bedienungsanleitung

Honeywell

Honeywell F300 Bedienungsanleitung

Honeywell

Honeywell PK 80148 Bedienungsanleitung

Honeywell

Honeywell HDLS Series Service-Handbuch

Honeywell

Honeywell 968XTP Bedienungsanleitung

Honeywell

Honeywell PLS550A Bedienungsanleitung

Honeywell

Honeywell Krom Schroder DL A Series Bedienungsanleitung

Honeywell

Honeywell ZW4009 Bedienungsanleitung

Honeywell

Honeywell RXSM100A3 Bedienungsanleitung

Honeywell

Honeywell Krom Schroder DG B Series Bedienungsanleitung

Honeywell

Honeywell BX Series Bedienungsanleitung

Honeywell

Honeywell GSX Series Bedienungsanleitung

Honeywell

Honeywell MICRO SWITCH BX2 Series Bedienungsanleitung

Honeywell

Honeywell C645A-E Bedienungsanleitung

Honeywell

Honeywell 272630D Bedienungsanleitung

Honeywell

Honeywell 43191680-105 Bedienungsanleitung

Honeywell

Honeywell MAXPRO-Net Montageanleitung

Honeywell

Honeywell CLMSOPS5M Bedienungsanleitung

Honeywell

Honeywell ZW4201 Bedienungsanleitung

Honeywell

Honeywell HBT083P Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch

5/99 62-86-33-10 – Kit 1

10260A series Auto/Manual Switch kit

Replacement/Upgrade Instructions

51309623-502

Document Number

Form: 62-86-33-10

Effective: 5-27-99

Supersedes: None

Summary

This kit contains a new auto/manual switch assembly for your 10260A actuator.

Procedure

See Table 1 for procedure.

WARNING

Disconnect power before accessing components inside the instrument.

ATTENTION

When working with circuit cards always protect against electrostatic discharge by wearing a grounded wrist

strap.

62-86-33-10 – Kit 5/992

Table 1 10260A Auto/Manual Switch Installation Procedure

Step Action

1Remove lower rear cover.

2Remove terminal board plate.

3If replacing the switch, disconnect switch wires and remove switch:

•Disconnect auto/manual switch wires from TB1-1, TB1-8, TB1-9, TB2-12, TB2-13, TB4-28, TB4-

29. (TB1 is the top terminal board. TB1-1 is the leftmost terminal on the top terminal board.)

•Remove switch knob by pulling it off the shaft.

•Remove nut securing switch to side of unit.

•Pull switch out of unit side wall.

4Install new switch:

•See Figure 1. Attach switch label to side wall.

•Remove nut from threads on switch. Insert switch through side wall. Make sure the stub

engages the small hole.

•Screw the nut onto the switch shaft and tighten it securely.

•Attach knob to shaft with set screw on flat side of shaft.

Label Auto/Manual Switch

Knob

Figure 1 Auto/Manual Switch Installation

5Connect switch wires:

•If adding (not replacing) the switch, remove blue and orange wires from TB1-8 and 9. Connect

blue wire to TB2-13 and orange wire to TB2-12.

•If adding or replacing the switch, one at a time connect auto/manual switch wires as follows.

Some terminals have dual (piggyback) wires attached; make sure the wires are attached to the

correct terminals. Make sure piggyback wires on outermost terminals are facing the inner

terminals, not facing away from the terminals. For example, TB1-1 should have its piggyback

terminal positioned between TB1-1 and TB1-2.

Black TB1-1, white TB1-8, brown TB1-9, green TB2-12, violet TB2-13, orange TB4-28, red TB4-29.

6Reattach terminal board plate.

7Install new gasket and reattach cover.

5/99 62-86-33-10 – Kit 3

Table 1 10260A Auto/Manual Switch Installation Procedure

Step Action

8Check switch for proper operation:

•Reconnect power.

•Set switch to CW and check for clockwise motion.

•Set switch to CCW and check for counterclockwise motion.

•Set switch to A/M and check for motion per 4-20 mA.

•If motion is incorrect, disassemble and check wiring in step 5. Repeat steps 6-8.