Honeywell 5869 Bedienungsanleitung

The 5869 Hold-Up Switch/Transmitter is a finger-operated

RF transmitting device. It is typically mounted under a

counter or money draw for inconspicuous operation.

When the transmitter is activated, it emits an RF signal to

the receiver. The security system control panel sends a

burglary alarm to the central station when a RF signal is

received from an enrolled Hold-Up Switch/Transmitter.

Once activated, the 5869 Hold-Up Switch/Transmitter can

only be reset by the reset key. The 5869 also incorporates

tamper switches that are activated when the cover is

removed, or if the unit is forcibly removed from its

installation location.

• No wires to run

• Front and back tamper resistant

• Easily mounted

• Quick enrollment

• Includes battery

FEATURES

5869

HOLD-UP SWITCH/TRANSMITTER

Physical

• 1-15/16" W x 5-15/16" H x 1 3/16"D

(50mm x 150mm x 30mm)

Frequency

• 345 MHz

Battery

• 3V Lithium ADEMCO 466

or equivalent

Agency Listings

• UL listed for Household Burg UL

1023,Hold-up Burg UL 636 and

CUL 634

• For certified UL commercial

installations, use with 5881ENHC

tamper-protected wireless receiver

Compatibility

• Fully compatible with all

VISTA Control Panels

SPECIFICATIONS

HOLDUP

TRANSMITTER

DEVICE

MOUNTING

HOLE

COVER

SCREW

MOUNTING

HOLE

COVER

ATTACH

HOLE

TRIGGER

INSIDE VIEW

WITH

CIRCUIT BOARD

RESET

KEY

COVER TAMPER

RELEASE SWITCH

LITHIUM

BATTERY

MOUNTING

HOLE

MOUNTING

HOLE

5869-001-V0

COVER

SCREW

COVER

ATTACH

HOLE

BREAKAWAY

TAMPER

RELEASE TAB

SCREW

HOLE

Figure 1

ORDERING

5869 Hold-Up Switch/Transmitter

5869

HOLD-UP SWITCH/TRANSMITTER

Mount the 5869 under a counter or

money drawer for easy access by the

cashier. Refer to the steps and figures

that follow for typical mounting

instructions. Before mounting the 5869

permanently, perform Go/No Go tests

to verify adequate transmitter signal

strength at desired mounting location

(refer to the Security System Control

Panel Installation and Setup Guide).

1. Remove the two screws (Figure 1)

securing the cover to the 5869 case.

NOTE: The holes located in the opposite corner

to the screws that secure the cover to the case,

provide a means for securing the transmitter to

the counter or drawer.

2. Using the case as a drill

template, position the case

in the desired location.

3. Drill a 1/16"pilot hole at the

breakaway tamper release

hole and the two case mounting

holes (Figure 2).

4. Attach the case to the counter or

money drawer using one No. 6 x 3/4

screw (supplied) at the breakaway

tamper release.

5. Install the battery (see BATTERY

INSTALLATION/REPLACEMENT).

6. Secure the cover to the case with

the two screws removed in step 1.

7. Secure the assembled case to

the counter or drawer using the

two No. 6 x 2 mounting screws

supplied (Figure 2).

INSTALLATION

The 5869 Hold-Up Switch/Transmitter

should be programmed as a 24-hour

silent zone type. Refer to the Security

System Control Panel Installation and

Setup Guide for programming

instructions.

• During programming of the control

panel, the 5869 Hold-Up

Switch/Transmitter should be treated

as “RF” (i.e., supervised RF) Type

• The 5869 is one closed input loop

zone (loop 1)

Battery Installation/Replacement

1. Remove and retain screws securing

the 5869 cover.

2. Observing correct polarity, insert the

battery into the battery holder.

NOTE: Use care not to bend the antenna while

attempting to install battery.

3. Re-install screws to secure cover

and/or assembly. Refer to Figure 1.

PROGRAMMING

5869-002-V0

MOUNTING

HOLE

TRIGGER

HOLE

TRIGGER

BREAKAWAY

TAMPER

RELEASE

RESET

KEY

COVER

TAMPER

RELEASE

SWITCH

MOUNTING

HOLE

COVER

SCREW (2)

No. 6X1/2

COVER

LITHIUM

BATTERY

CIRCUIT

BOARD

COVER

ATTACH HOLE

COVER

ATTACH

HOLE

MOUNTING

SCREW (2)

No. 6X2

BREAKAWAY

TAMPER

RELEASE

SCREW HOLE

INDEX

TAB

COVER

SCREW

NOTE

CIRCUIT BOARD REMOVED

FOR CLARITY ONLY. DO NOT

REMOVE CIRCUIT BOARD

DURING INSTALLATION.

Figure 2

Andere Honeywell Schalten Handbücher

Honeywell

Honeywell KSL Series Bedienungsanleitung

Honeywell

Honeywell Galaxy 2 Series Bedienungsanleitung

Honeywell

Honeywell PLS531A Bedienungsanleitung

Honeywell

Honeywell 968XTP Bedienungsanleitung

Honeywell

Honeywell RPLS740B Bedienungsanleitung

Honeywell

Honeywell ZW4005 Bedienungsanleitung

Honeywell

Honeywell Krom Schroder DG H Series Bedienungsanleitung

Honeywell

Honeywell RXSW100A3CULH Bedienungsanleitung

Honeywell

Honeywell ADEMCO 270R Montageanleitung

Honeywell

Honeywell RTS-CSA Bedienungsanleitung

Honeywell

Honeywell RPLS730B Bedienungsanleitung

Honeywell

Honeywell Home HS9HUB Bedienungsanleitung

Honeywell

Honeywell MICRO SWITCH XP-4042 Bedienungsanleitung

Honeywell

Honeywell ZW4003 Bedienungsanleitung

Honeywell

Honeywell CLMSOPS5M Bedienungsanleitung

Honeywell

Honeywell 14CE100 Series Bedienungsanleitung

Honeywell

Honeywell Z Series Bedienungsanleitung

Honeywell

Honeywell CX Series Kurzanleitung

Honeywell

Honeywell ZW4008 Bedienungsanleitung

Honeywell

Honeywell 39346 Bedienungsanleitung

Honeywell

Honeywell MICRO SWITCH BX Series Bedienungsanleitung

Honeywell

Honeywell krom schroder DL K Series Bedienungsanleitung

Honeywell

Honeywell PLS731B Bedienungsanleitung

Honeywell

Honeywell ZW4203 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung