Honeywell MDDS8202 Bedienungsanleitung
SCMDDS8202
MDDS8202/HBDS8202
SATELLITE DISTRIBUTION
INSTALLATION INSTRUCTIONS
Honeywell FutureSmart Products Satellite Installation Guide
Pg 2 Honeywell FutureSmart Products
The DBS Distribution Hub provides signal distribution to up to 8 receivers or DVR’s from a dual LNB system or from a
Multi-Satellite System.
The HBDS8202 occupies one expansion slot in any SuperPro Series Panel.
The MDDS8202 occupies 12” of both sides of a QuickNetwork install can.
Features
• Distribute a dual feed satellite system to 8
receivers
• Distribute a four feed satellite system (Multi-
Satellite System) to 8 receivers
• Will distribute (diplex) Antenna or Cable TV to all
the 8 outputs
**Multi-Satellite System has either 2-Dual LNB dishes pointed at different
satellites or a single elliptical dish with multiple horns pointed at more than one
satellite.
Specifications
Input Frequency Range: 950-2150 MHz (LNB A / LNB B)
54-806MHz (UHF/VHF)
Output Frequency Range: 54-2150 MHz (Each Output)
Insertion Loss: -5dB 54-806MHz
0dB 950-2150
Noise Figure: 4.8dB min
Cross Polar Isolation 30dB min
Current Consumption: 60mA
Power Adaptor: 120VAC 60Hz Input
24VDC 1000mA Output
22kHz Tone Output: 22 ±4kHz continuous,
650 ±300 mVp-p
Compatibility
Table
DirecTV Dish
Network
Dual LNB Yes Yes
**Multi-Satellite Yes No (Dish 500)
Single LNB No No
Honeywell FutureSmart Products Satellite Installation Guide
Honeywell FutureSmart Products Pg 3
Installation for a standard Dual LNB
system.
1.The dual feeds from the satellite dish need to
hook up to one LNB/A port and one LNB/B port
on the DBS distribution hub.
2. If there is no UHF/VHF antenna present in the
system the diplexers are not needed between the
distribution hub and the receivers.
3. Power is required to make the hub function
properly. Use the transformer with the coax
connector and an RG6 patch cord in hook power
to the DBS distribution hub (use only solid core
copper RG6 for power).
Installation for a Multi Satellite
system.
1.The feeds from the satellite dish need to
hook up to the LNB/A and LNB/B ports.
2. If there is no UHF/VHF antenna present
in the system the diplexers are not needed
between the distribution hub and the
receivers.
3. Power is required to make hub function
properly. Use the transformer with the coax
connector and a RG6 patch cord in hook
power to the DBS distribution hub (use only
solid core copper RG6 for power).
Power
24VDC
LNB/A LNB/A LNB/B LNB/BANT IN
1 2345678
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
UHF/VHF
Antenna
Optional
Multi
satellite
dish
Power Supply
120VAC
Power Supply
120VAC
Power
24VDC
LNB/A LNB/A LNB/B LNB/B
ANT IN
1 2345678
Dual LNB
dish
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
Diplexer
Receiver
UHF/VHF
Antenna
Optional
Honeywell FutureSmart Products Satellite Installation Guide
Pg 4 Honeywell FutureSmart Products
IMPORTANT!!
CAUTION: To prevent electric shock, do not use this plug with an extension cord, receptacle or other outlet unless the blades can be
fully inserted to prevent blade exposure.
NOTE TO INSTALLER: This reminder calls the system installer’s attention to Article 820-22 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
165 Eileen Way, Syosset, NY 11791
Copyright © 2004 Honeywell International Inc.
www.honeywell.com/security
View from back side of Modules Front view with modules installed
Installing an eight receiver DirectTV
SATV Distribution System in a QNIC
RG6 Coax Cable from/to receivers
Triple LNB
SATV dish
Antennae
Plug transformer into
MDDS8202 and then into 110V
outlet
Mini Digital Coax
Jumpers
The MDC8202 is used to feed between five
and eight receivers. If one to four DirectTV
receivers are used then you can use an MDP-3
and/or the pass through connections on an
MDC4XX module.to feed up to four. For
DishNetworks you will need to use
DishNetworks Proprietary Hardware to expand
beyond four.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Honeywell Schalten Handbücher
Honeywell
Honeywell VC Series Bedienungsanleitung
Honeywell
Honeywell 10260 Series Bedienungsanleitung
Honeywell
Honeywell S688A Bedienungsanleitung
Honeywell
Honeywell ZW4103 Bedienungsanleitung
Honeywell
Honeywell nfs2-3030 Bedienungsanleitung
Honeywell
Honeywell RPLS731B Bedienungsanleitung
Honeywell
Honeywell DG T Series Bedienungsanleitung
Honeywell
Honeywell BX Series Bedienungsanleitung
Honeywell
Honeywell Limitless WGLA Series Bedienungsanleitung
Honeywell
Honeywell ZW4008 Bedienungsanleitung
Honeywell
Honeywell PK 88231 Bedienungsanleitung
Honeywell
Honeywell DCM/SN DIFF Bedienungsanleitung
Honeywell
Honeywell ZW4203 Bedienungsanleitung
Honeywell
Honeywell ZW4005 Bedienungsanleitung
Honeywell
Honeywell C437D Bedienungsanleitung
Honeywell
Honeywell 43191680-105 Bedienungsanleitung
Honeywell
Honeywell 39351 Bedienungsanleitung
Honeywell
Honeywell KSL Series Bedienungsanleitung
Honeywell
Honeywell 39348 Bedienungsanleitung
Honeywell
Honeywell ZW2004 Bedienungsanleitung
