Honeywell 10260 Series Bedienungsanleitung

Inhaltsverzeichnis

Andere Honeywell Schalten Handbücher

Honeywell

Honeywell WBX Series Bedienungsanleitung

Honeywell

Honeywell ZW4103 Bedienungsanleitung

Honeywell

Honeywell ZW4003 Bedienungsanleitung

Honeywell

Honeywell ZW4005 Bedienungsanleitung

Honeywell

Honeywell MDDS8202 Bedienungsanleitung

Honeywell

Honeywell GSX Series Bedienungsanleitung

Honeywell

Honeywell Q640 Bedienungsanleitung

Honeywell

Honeywell 272630D Bedienungsanleitung

Honeywell

Honeywell MICRO SWITCH XP-4042 Bedienungsanleitung

Honeywell

Honeywell ZW4008 Bedienungsanleitung

Honeywell

Honeywell GLS Series Bedienungsanleitung

Honeywell

Honeywell 5869 Bedienungsanleitung

Honeywell

Honeywell CLMSOPS5M Bedienungsanleitung

Honeywell

Honeywell GKN Series Bedienungsanleitung

Honeywell

Honeywell EVN2000 Series Montageanleitung

Honeywell

Honeywell C6097B Bedienungsanleitung

Honeywell

Honeywell 10260A Series Bedienungsanleitung

Honeywell

Honeywell PLS550A Bedienungsanleitung

Honeywell

Honeywell miniMAX Bedienungsanleitung

Honeywell

Honeywell Ademco VistaView-100 Montageanleitung

Honeywell

Honeywell 968XTP Bedienungsanleitung

Honeywell

Honeywell OP-AR Bedienungsanleitung

Honeywell

Honeywell ZW4009 Bedienungsanleitung

Honeywell

Honeywell 14CE100 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch

62-86-33-34 Page 1 of 2

10260 Series Auto/Manual Switch kit

Replacement/Upgrade Instructions

51309623-501

Document Information

Number: 62-86-33-34

Effective: 5/04

Supersedes: None

Summary

This kit contains a new auto/manual switch assembly for your 10260 actuator.

Procedure

See Table 1 for procedure.

WARNING

WARNING

Disconnect power before accessing components inside the instrument.

ATTENTION

When working with circuit cards always protect against electrostatic discharge by wearing a grounded wrist

strap.

Table 1 10260A Auto/Manual Switch Installation Procedure

Step Action

1 Remove lower rear cover.

2 Remove terminal board plate.

3 If replacing the switch, disconnect switch wires and remove switch:

• Disconnect the auto/manual switch wires from terminals 9, 10, 11, and 12 (upper terminal board).

Disconnect the three auto/manual switch wires connected to the bottom terminal board, record the colors of

the wires removed and their associated terminal numbers.

• Remove switch knob by pulling it off the shaft.

• Remove nut securing switch to side of unit.

• Pull switch out of unit side wall.

Page 2 of 2 62-86-33-34

Step Action

4 Install new switch:

• See Figure 1. Attach switch label to side wall.

• Remove nut from threads on switch. Insert switch through side wall. Make sure the stub

engages the small hole.

• Screw the nut onto the switch shaft and tighten it securely.

• Attach knob to shaft with set screw on flat side of shaft.

5 Connect switch wires:

• If adding (not replacing) the switch, add the second terminal board (terminals 13 thru 24) if needed.

• If adding (not replacing) the switch, remove the wires connected to terminals 11 and 12.

Connect the auto/manual switch red wire to terminal 11 and the red-black wire to terminal 12.

Select 3 adjacent terminals on the bottom terminal board, connect the auto/manual switch black wire

(120/240VAC), the violet wire (CW) and green-black wire (CCW).

• If adding or replacing the switch, connect the auto/manual switch violet-black wire to terminal 9 and brown-

black wire to terminal 10.

6 Reattach terminal board plate.

7 Install new gasket and reattach cover.

8 Check switch for proper operation:

• Reconnect power.

• Set switch to CW and check for clockwise motion.

• Set switch to CCW and check for counterclockwise motion.

• Set switch to A/M and check for motion per 4-20 mA.

• If motion is incorrect, disassemble and check wiring in step 5. Repeat steps 6-8.