Honeywell POL-200-TS Bedienungsanleitung

POL-200-TS User Manual

1/16

User Manual

ANALOGUE LOOP VERIFICATION

TOOL

POL-200-TS

POL-200-TS User Manual

2/16

Security Informaon

¡Several damage! Please, before to connect any external cable, ensure that loop cable has

been disconnected from panel loop terminals and the panel is complete powered down.

Check for the right terminal connecons and that there is no external voltage between

cables to be connected.

Baery life maximum 3 years, check the manufacture year!

Danger of explosion in case of inappropriate replacement of the baery! Baery waste

disposal by manufacturer instrucon!

Cauon! The warranty in case of damages is limited if the operaon and installaon in-

strucons are not observed. The company is not liable for any consequenal or incidental

damages. This installaon instrucon must be read thoroughly before start mounng.

Dissasembling: In accordance with the regulaons 2002/96/EG (WEEE), aer being dis-

assembled, electrical and electronic equipment is taken back by the manufacturer for a

proper disposal.

Set Language

POL-200-TS language menu. To change, select the opon and the corresponding language.

Restart the device.

POL-200-TS User Manual

3/16

Contents

1. Introducon ....................................................................................... 4

2. Connecon ......................................................................................... 5

3. Mul-meter ........................................................................................ 6

4. Loop.................................................................................................... 7

5. Map .................................................................................................. 11

6. Events recording ............................................................................... 11

7. Conguraon .................................................................................... 13

8. Troubleshoong ............................................................................... 14

9. Technical Characteriscs .................................................................. 15

10. CE conformity ................................................................................. 16

Page

POL-200-TS User Manual

4/16

1. Introduction

The POL-200-TS is a compact, graphic and intuive hand-held tool (dimensions are 177mm x

97mm x 44mm) assists:

Installer in commissioning and tesng Noer or Morley eld loops before the conguring of

the panel can start.

Maintainer in the diagnosis and vericaon of the state of the installaon and the connected

eld equipment, verifying the wiring map to detect the possible changes made over me.

The six internal, 2500mA NiMH, rechargeable baeries provides the installer with sucient

capacity, up to 6 hours depending on the loop load.

POL-200-TS is designed to be used only by trained personnel in order to properly interpretaon

the informaon read.

Please note that POL-200-TS is a device designed to help you check the quality of the line and

signal in your installaon. POL-200-TS is not a re protecon equipment, it only provides the

necessary informaon of support for the idencaon and soluon of faults to a qualied

technician.

POL-200-TS User Manual

5/16

2. Connecting

The POL-200-TS unit reports any short-circuit fault

condions in the loop (showing a lightning icon ),

reverse polarity wiring (a diode icon ) and is also

able to idenfy within seconds the total number of

devices connected to the loop.

Conrm that the loop wiring is correct:

• The characteriscs considered are for wiring in closed loop mode (panel output and back

to it)

• The maximum resistance allowed from the OUTPUT end of the re detecon

panel (or from POL-200-TS) to the INPUT in the re detecon panel is 40 ohms.

Refer to the installaon recommendaons associated with the re detecon control center

where you will connect the monitored loop with POL-200-TS. La siguiente tabla muestra los

valores resisvos aproximados para los dos recommended loop cable types:

• Shielded/screen cable should only be connected to ground, GND, at one point inside the

re panel. The POL-200-TS allows the user to conrm that the shield is connuous, so it

should be approximately twice (2x) and three (3x) mes the resistance of the negave

conductor. So, in case that the negave conductor has a:

• Capacitance between loop conductors so + and – is below 0.5mF or 500nF

• Impedance between posive and cable shield (Innite).

POL-200-TS User Manual

6/16

3. Multi-meter

Aer the connecon check that POL-200-TS has

the correct load level, please note that baeries

with an insucient charge level can falsify the

measurements.

You will access the Mulmeter funcon from the

main screen. Verify that the line impedance

condions are adequate as described in the pre-

vious secon.

Then check for each voltage range, 0V, 5V and 24V, the voltages and consumpon shown.

Check for possible dris, short circuits, faulty elements, connecons or inadequate system de-

vices or external to the system depending on the values obtained.

The reading at 24v will provide a reference voltage drop in the loop

Under the 5V reading should not have consumpon, check the possible existence of derivaons

or inducons.

POL-200-TS User Manual

7/16

4. Loop

The tool recognizes the sensors and modules on

the loop before powering the re alarm control

panel (FACP). The POL-200-TS unit is compable

with the CLIP (Classic Loop Interface Protocol)

with 99 sensors and 99 modules and the new Ad-

vanced or Opal protocol with up to 159 sensors

and 159 modules.

In the auto-programming menu, we will idenfy the number of detectors or modules that are

connected in the loop idenfying them according to their type:

POL-200-TS User Manual

8/16

CLIP PROTOCOL

• “O” Opcal Sensor

• “H” or “T” Heat/Thermal sensor

• “I” ionizaon sensor

• “M” Mul-Sensor. Opcal/ thermal

• “P” Pinnacle Laser

• “L” VIEW Laser

• “S” Smart Mul-criteria

Secon of Modules - Symbols of idenca-

on by type:

• “I” or “E” Input Modules including

Manual Call Points

• “O” or “S” Output modules

• “R” Output modules without End-of-

Line (EOL) by default Relays

• “Z” Zone modules for convenonal de-

tectors

ADVANCED PROTOCOL

For advanced protocol loops, POL-200-TS

also idenes the following elements:

• “S” SMART 4

• “B” Beam detectors

• “P” Indoor Manual Call Point

• “M” FAAST Aspiraon unit

POL-200-TS User Manual

9/16

Lower Case or Capital Leer: in case that in the auto learn a Lower case leer appears please

conrm in the conguraon that the correct protocol is selected between these dierence op-

ons “Noer”, “Morley”, “System Sensor” or “Honeywell HBS”.

In case that in one address a device change the type ID or from lower case to capital leer, please

check the wiring in this device as its answer is not correct. Possible reason is a defecve device

or noise due to interferences. Please also check that the device is not faulty or there is noise due

to interference.

A “?” Character in the ID type eld can be indicave of a problem in the device or due to prob-

lems in the wiring line.

A “-” character in ID type may be indicave of duplicate address.

For each sampling POL-200-TS idenes the changes that have occurred since the previous sam-

pling, for that, the type of ID that idenes each address will appear in red or black. The red

color indicates that a change has occurred.

To get more details about each of the elements, select them by clicking directly on them or with

the help of the cursors and mark them by pressing the buon . Holding down this buon

you will get the details of the selected item within the sampling table.

The PWs value is for Honeywell technical team references, PW1 should be around 150 +/- 10%

in Honeywell and Morley while around 300 +/- 10% for Noer / System Sensor. Other values

outside these range should be reported to Honeywell technical support for advice.

To select between CLIP and ADVANCED Protocol please access the conguraon screen and in

the buon line select one of the two protocols available.

POL-200-TS User Manual

10/16

Select one of the items within the sampling table with the help of the arrows (arrows in the right

margin of the screen) or by clicking on the screen. Press the buon to access the advanced

user informaon screen.

From the self-programming menu and pressing the “List” buon, the user can display a summa-

ry of installed elements. Clicking once more on the icon you will have access to a more

detailed list of the devices of the loop, use the scroll keys located in the right side of the screen

to move of 1 in 1 or in blocks of 10.

Andere Handbücher für POL-200-TS

Inhaltsverzeichnis

Andere Honeywell Prüfgeräte Handbücher

Honeywell

Honeywell BW MicroDock II Bedienungsanleitung

Honeywell

Honeywell IQ Force Dock Bedienungsanleitung

Honeywell

Honeywell TKA295 Bedienungsanleitung

Honeywell

Honeywell TB7200 Series Bedienungsanleitung

Honeywell

Honeywell TESTAIR 4 Bedienungsanleitung

Honeywell

Honeywell Vibrex 2000 Bedienungsanleitung

Honeywell

Honeywell S300RPTU Bedienungsanleitung

Honeywell

Honeywell MicroDock II Bedienungsanleitung

Honeywell

Honeywell HPBLT Technisches Handbuch

Honeywell

Honeywell Posi3 USB Bedienungsanleitung

Honeywell

Honeywell Posi3 USB Bedienungsanleitung

Honeywell

Honeywell Enraf VITO 762 Bedienungsanleitung

Honeywell

Honeywell FG701 Bedienungsanleitung

Honeywell

Honeywell Posi 3 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung