Honeywell CT3200 series Bedienungsanleitung

69-1631-1

OWNER’S GUIDE

® U.S. Registered Trademark

CT3200 Programmable Thermostat

Welcome to the world of comfort and energy savings with your

new Honeywell Programmable Thermostat. Your new thermostat

will automatically control the temperature in your home, keeping

you comfortable while saving energy.

Weekday/Weekend (5-day/2-day)

Programmable Heat and/or Cool

Low Voltage (20 to 30 Vac)

Thermostat and Mounting Plate

Model CT3200

Table of Contents

Installation .................................................................................................................................................................. 2

Programming.............................................................................................................................................................. 12

Operation.................................................................................................................................................................... 18

Frequently Asked Questions ...................................................................................................................................... 22

Customer Assistance ................................................................................................................................................. 23

Limited Warranty ........................................................................................................................................................ 24

69-1631—1 2

MERCURY NOTICE

If you are removing an old thermostat that contains mercury in a sealed tube

(Fig. 1), do not place the old thermostat in the trash. Contact your local waste

management authority for instructions regarding recycling and the proper

disposal of the old thermostat.

INSTALLATION

Verify You Have Correct Thermostat

Make sure that the CT3200 is the correct thermostat for your heating/cooling system. Read the compatibility chart

below to determine which system you have. If your system is not compatible with the CT3200, the table recommends

an alternate Honeywell model. If you are unsure what type of thermostat is right for your system, visit us on the Web at

www.honeywell.com/yourhome or call Honeywell Customer Care at 1-800-468-1502.

M3701

MERCUR

SWITCH

Fig. 1.

Heating/Cooling System

Compatible

with CT3200? Alternate Model

Conventional

Single stage systems that include warm air furnaces and hot water.

Yes

Electric Baseboard

Electric-powered heating strips located just above the floor, usually 120 to 240

volts.

No CT1950 for 240

volts

3 69-1631—1

Step 1. Prepare for Installation

1. Carefully unpack your new thermostat. Save your receipt and make sure you have the following parts:

• Thermostat and mounting plate

• Labels

• Screws and anchors

• Installation and Programming Instructions

2. Gather the needed tools and supplies listed below.

3. Make sure that your heating and cooling systems are working properly. If there is a problem with either system,

call a heating/air conditioning contractor—the problem may persist after you install the new thermostat.

IMPORTANT:

To avoid damaging the compressor in the air conditioner, do not operate the cooling system when the tem-

perature outdoors is below 50°F (10°C).

Steam

A steam boiler with radiator heat.

No CT3600

Heat Pump

Heating and cooling are produced from the same outdoor unit (compressor) with

no auxiliary or backup heat.

No CT3600

Multistage Heat Pump

Heating and cooling are produced from the same outdoor unit (compressor) with

auxiliary or backup heat.

No CT3611

Multistage Conventional

A heating or cooling system with more than one stage.

No See your

contractor

Required Tools and Supplies Optional Tools

• Two AA alkaline batteries. Honeywell recommends Energizer®

batteries.

• Screwdriver.

• Hand or power drill with 3/16-inch or 7/32-inch drill bit.

• Pencil.

• Wire cutter/stripper or sharp knife.

• Level.

• Electrical tape.

Heating/Cooling System

Compatible

with CT3200? Alternate Model

69-1631—1 4

Step 2. Remove Old Thermostat

Fig. 2. a. Turn off power to the heating/cooling system, either at the

furnace or at the fuse/circuit breaker panel.

b. Remove the cover of your old thermostat (Fig. 2).

c. Unscrew and remove the old thermostat’s mounting plate

from the wall, but do not disconnect the wires.

d. Inspect the old thermostat wiring. If wiring meets any of

the following conditions, see special wiring instruc-

tions section after Step 7.

Fig. 3. • The old thermostat is a clock thermostat with wires attached

to the C or C1 terminals.

• The old thermostat has six or more wires, excluding wires

attached to C or C1 terminals.

• The old thermostat has three wires.

• There are five wires connected to the old thermostat.

• There are extra wires that are not connected to the old

thermostat.

e. Using enclosed labels, mark wires with letter of terminal it is

attached to on the old thermostat (Fig. 3). Do not label

using colors. If labels do not match letters on old thermostat

terminals, see wiring cross reference table in Special Wiring

Instructions section.

Fig. 4. f. Disconnect the wires from the old thermostat and wrap the

wires around a pencil to keep them from falling back into the

wall.

NOTE: Remember, if your old thermostat contains mercury,

you must recycle it. See Mercury Notice for more

recycling information.

✓Check your progress

Your wall should now look like Fig. 4.

M2014

M19086

WIRES THROUG

WALL OPENING

M20133

5 69-1631—1

Step 3. Install Mounting Plate

Fig. 5. a. Separate the mounting plate from the thermostat using a

coin, as shown in Fig 5.

b. Position the mounting plate on the wall. Be sure the mount-

ing plate is flush against the wall and none of the wires are

trapped behind it.

c. Level the mounting plate and use a pencil to mark the cen-

ter of the mounting plate screw holes.

d. Remove the mounting plate and drill holes at the locations

marked.

• For drywall, drill two 3/16-inch holes.

• For plaster or wood, drill two 7/32-inch holes.

Fig. 6. e. If installing in drywall, gently tap the anchors (provided) into

the drilled holes until they are flush with the wall.

f. Reposition the mounting plate over the holes, pull the wires

through the wiring opening, and loosely insert the mounting

screws into each of the drilled holes or anchors (Fig. 6).

g. Make sure the mounting plate is level and tighten the

mounting screws.

Fig. 7. ✓ Check your progress

The mounting plate is now mounted on the wall and should look like

Fig. 7.

M20139

M20129

M2012

69-1631—1 6

Step 4. Set Thermostat for Your Type of Heating System

IMPORTANT:

Setting your thermostat correctly

for your type of heating system

allows it to maintain accurate

temperature control, minimize

swings in the temperature of the

room, and efficiently run the fan.

a. Use the FUEL SWITCH on the

back of the thermostat to set your

new thermostat for the type of fuel

that your heating system uses: F–

gas or oil, or E–electric.

NOTE: This setting enables

proper fan operation.

b. Use DIP switches 1 and 2 on

the back of the thermostat to set

your new thermostat for your type

of heating system. See the Heat-

ing System Table on the next

page to find the correct settings.

NOTE: These DIP switches are

factory-set for a warm air, gas, or

oil heating system.

c. The thermostat is set to display the temperature in degrees Fahrenheit (°F). If you want to display the tem-

perature in degrees Celsius (°C), turn DIP Switch 3 to Off position.

d. You can install the batteries and program your thermostat now, or you can wait until the thermostat is

mounted on the wall. To install the batteries, see Step 7.To program the thermostat, see the Programming

section.

Fig. 8.

M2063

W Y G

C R R

THERMOSTAT BACK

DISPLAY F

DISPLAY C 3 - ON

3 - OFF

FUEL SWITCH

WARM AIR

FURNACE 1 - ON 2 - ON F

1 - OFF 2 - ON F

1 - ON 2 - OFF E

FUEL SWITCH

POSITION

DIP SWITCH

POSITION

HEATING

SYSTEM

OFF ON

HOTWATEROR

HIGHEFFICIENCY

ELECTRIC

FURNACE

7 69-1631—1

Heating System Table

Step 5. Wire Thermostat Terminals

Type of System

D I P S w i t c h e s

1 and 2 Fuel Switch

Warm air, gas, or oil heating system with an efficiency rating under 90%.

(The furnace efficiency rating should be on the furnace.)

Use factory setting

1–On; 2–On

High-efficiency furnace such as a 90% or greater AFUE (Average Fuel

Utilization Efficiency) unit

1–Off; 2–On F

Hot water boiler 1–Off; 2–On F

Electric furnace 1–On; 2–Off E

Fig. 9. a. Hold thermostat as shown in Fig. 9.

b. Using the labels on the wires, match letter of your old ther-

mostat wire with the corresponding terminal on the back of

your new thermostat.

NOTE: If letters on old thermostat terminals do not match letters on

new thermostat terminals, all old wires may not need con-

necting to new thermostat. See Special Wiring Instructions

section.

Fig. 10. c. Loosen terminal screws and slip each wire beneath its

matching terminal (Fig 10).

d. Securely tighten terminals.

M2012

INSERT

STRAIGHT

UNDER

SCREW HEAD

/16 in.

(

8 mm)

TRIP

END OF WIR

VISIBLE HER

M20126

69-1631—1 8

Step 6. Mount Thermostat

Fig. 11. Fig. 12. e. Align the tabs at the top of the thermostat

with the tabs at the top of the mounting

plate (Fig. 11).

f. Press the lower edge of the case to latch

the bottom of the thermostat (Fig. 12)

M2013

9 69-1631—1

Step 7. Install the batteries

Special Wiring Instructions

Clock thermostat with C or C1 terminals

A clock thermostat has one or two extra wires attached to the C or C1 terminals that allow the clock to operate. These

wires are not used during the installation of your new 3200 Thermostat and must be insulated from each other to avoid

damaging your electrical circuit.

a. Make sure that power to the heating/cooling system is turned off.

b. Locate the wires that are connected to the clock terminals marked C or C1.

c. As you disconnect the wires, do not allow these wires to touch.

d. Wrap the wires separately, using electrical tape to insulate the wires.

e. Place the wires where they do not interfere with the operation of the new thermostat.

You will not connect these wires to your 3200 Thermostat.

f. Continue with the installation.

Fig. 13.

Fig. 14.

IMPORTANT:

Batteries must be installed for programming and operation of

the thermostat and heating/cooling system. Honeywell rec-

ommends using Energizer® batteries.

a. Make sure that the System switch is set in the OFF position.

b. Using a coin, open the battery door as shown in Fig. 13.

c. Install the batteries. Make sure that the positive and nega-

tive terminals are oriented correctly as marked inside the

battery case.

d. Replace the battery door.

e. Remove the clear plastic label from the digital display.

✓Check your progress

When the batteries are installed correctly, the digital display flashes all

entries once, then begins to flash a default time and the current

temperature (Fig. 14). The flashing continues until you begin to

program the thermostat. You are now ready to program the thermostat.

See Programming section.

M1719C

REMOVING

BATTERY

DOOR

69-1631—1 10

Six or more wires

If your old thermostat has six or more wires (excluding clock wires attached to the C or C1 terminals), your heating/

cooling system is most likely a variation of a heat pump or multistage system. Your 3200 Thermostat will NOT work

with such systems and should be returned to the place of purchase. See the thermostat compatibility table for

information about which programmable thermostat will work with your system.

Three thermostat wires

If you have three wires for heating only and can operate the fan using the fan ON switch, the 3200 Thermostat will

work with your system. Continue the installation procedure.

If you have a three-wire heating-only system and cannot operate the fan using the fan ON switch, the 3200

Thermostat will probably NOT work with your system. Contact your heating contractor for installation assistance.

Wires that are not connected to old thermostat

If there are extra wires that do not connect to your old thermostat, do not label them. You will not connect these wires

to your new thermostat. Tape off the wires individually with electrical tape and place them where they will not interfere

with the operation of the new thermostat. Continue the installation procedure.

Five wires connected to old thermostat

Your new thermostat has a factory-installed metal jumper between the R and Rc

terminals (Fig. 15). Remove the jumper before wiring the R and Rc terminals.

Thermostat C Terminal

This thermostat does not use the C wiring terminal.

M20127

JUMPER (FACTORY-

INSTALLED). REMOVE

IF 5-WIRE SYSTEM

WY G

Fig. 15.

Andere Handbücher für CT3200 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell RTH1100 series Bedienungsanleitung

Honeywell

Honeywell T6 Pro Hydronic Bedienungsanleitung

Honeywell

Honeywell Q539A Bedienungsanleitung

Honeywell

Honeywell TH8320R1003 Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Pro Wi-Fi Bedienungsanleitung

Honeywell

Honeywell T6 Pro Z-Wave Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell TRADELINE Y594 Fehlerbehebungshandbuch

Honeywell

Honeywell TB3 Series Bedienungsanleitung

Honeywell

Honeywell 36 Bedienungsanleitung

Honeywell

Honeywell RTH7500 Series Bedienungsanleitung

Honeywell

Honeywell WebStat T7350 Benutzerhandbuch

Honeywell

Honeywell VisionPRO IAQ Bedienungsanleitung

Honeywell

Honeywell T8535L Bedienungsanleitung

Honeywell

Honeywell AQUASTAT L6188A Bedienungsanleitung

Honeywell

Honeywell 9000 color touchscreen Bedienungsanleitung

Honeywell

Honeywell UtilityPRO Series Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Bedienungsanleitung

Honeywell

Honeywell RTHL2410 series Bedienungsanleitung

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell T8601D Bedienungsanleitung

Honeywell

Honeywell RTH7000 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung