Honeywell FocusPRO TH5110D Bedienungsanleitung

�

Non-Programmable Digital Thermostat

® U.S. Registered Trademark. Patents pending.

Installation

Guide

Must be installed by a trained, experienced technician

Read these instructions carefully. Failure to follow these instructions

can damage the product or cause a hazardous condition.

Need Help?

For assistance with this product please visit http://customer.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

This manual covers the following models

(Remove battery holder to find model number)

System Types

conditioning

three-wire zone valves (Series

valves



 

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

Mounting screws

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

�

Pull here to remove wallplate

from new thermostat.

Remove battery holder.

�

It's easier to grasp the wallplate

and remove it after completely

removing the battery holder.



 

Power options

Keep wires in this

shaded area

Connect C for primary AC power

(optional if batteries are installed).

Insert batteries for primary

or backup power.

Remove factory-

installed jumper

only for two-

transformer

systems.

Conventional Terminals:

transformer

W Heat relay (stage 1)

W2 Heat relay (stage 2)

Y Compressor contactor (stage 1)

Y2 Compressor contactor (stage 2)

G Fan relay

cooling transformer.

Heat Pump Terminals:

transformer

O/B Changeover valve

Y Compressor contactor

Y2 Compressor contactor (stage 2)

-TH5320U only

G Fan relay

Aux Auxiliary heat relay*

E Emergency heat relay*

L Sends output when set to Em. Heat

*Aux and E terminals combined on TH5320U only.

Wiring

Terminal designations

Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.



 

Wiring

Wiring guide — conventional systems

Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.

1H/1C System

(1 transformer)

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

W Heat relay

G Fan relay

Heat-only System

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay

Heat-only System

(Series 20) [5]

Rc [R+Rc joined by jumper]

R [1]

Heat-only System

(normally open zone valve) [5]

Rc [R+Rc joined by jumper]

R Power [1]

Y Normally open zone valve

1H/1C System

(2 transformers)

Rc Power (cooling transformer)

R Power (heating transformer)

Y Compressor contactor

W Heat relay

G Fan relay

Heat-only System

with Fan

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay

G Fan relay

Cool-only System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

G Fan relay

2H/2C System

(1 transformer) [6]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

2H/2C System

(2 transformers) [6]

Rc Power (cooling transformer)

R Power (heating transformer)

Y Compressor contactor (stage 1)

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

See [notes] below

NOTES

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means

and overload protection as required.

[2] Remove jumper for 2-transformer systems.

[4] Common connection must come from

cooling transformer.

[5]

Heat Only.

[6]

2Heat/2Cool Conventional.

O or B.

[8]

2Heat/1Cool Heat Pump.

[9]

2Heat/2Cool Heat Pump.

[10]

[11] L terminal sends a continuous output when

thermostat is set to Em. Heat. Connect

to Honeywell zoning panels to switch the

panel to Emergency Heat.

[12] Install field jumper between Aux and E if

there is no emergency heat relay.



 

Wiring

Wiring guide — heat pump systems

Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.

Thermostat mounting

Align the 4 tabs on the wallplate with

then push gently until the thermostat

snaps in place.

Push excess wire back into

the wall opening.

Plug wall opening with

non-flammable insulation.

1H/1C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

O/B Changeover valve

G Fan relay

2H/1C Heat

Pump System

(TH5220D only) [8]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

O/B Changeover valve

G Fan relay

Aux Auxiliary heat relay [12]

E Emergency heat relay [12]

L Sends output when set to Em. Heat [11]

2H/1C Heat

Pump System

(TH5320U only) [8]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

O/B Changeover valve

G Fan relay

Aux/E Auxiliary/Emergency heat relay

L Sends output when set to Em. Heat [11]

2H/2C Heat

Pump System

(TH5320U only) [9]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

O/B Changeover valve

G Fan relay

Y2 Compressor contactor (stage 2)

L Sends output when set to Em. Heat [11]

3H/2C Heat

Pump System

(TH5320U only) [10]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

O/B Changeover valve

G Fan relay

Aux/E Auxiliary/Emergency heat relay

Y2 Compressor contactor (stage 2)

L Sends output when set to Em. Heat [11]

See [notes] on page 4.



 

 

press and hold the and FAN

buttons until the display changes.

Function

number

Setting

Press or to change settings.

Press NEXT to advance to the next function.

Press DONE to exit and save settings.

Installer setup

Follow the procedure below to configure the thermostat to match the installed



Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.

1 System type 0 1 heat/1 cool conventional

1 1 heat/1 cool heat pump (no aux. heat)

normally open zone valves

4 Cool only

5 2 heat/1 cool heat pump (with aux. heat)

6 2 heat/2 cool conventional

8 1 heat/2 cool conventional

9 2 heat/2 cool heat pump (no aux. heat) - TH5320U only

TH5320U only

2 Changeover valve

(O/B terminal)

0 Changeover valve (O/B terminal energized in cooling)

1 Changeover valve (O/B terminal energized in heating)

3 Fan control

(heating)

0 Gas or oil furnace — equipment controls fan in heating

5 Stage 1 heat cycle

rate (CPH: cycles/hour)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

furnaces of over 90% efficiency

9 For electric furnaces

6 Stage 2 heat cycle

rate/Auxiliary heat

cycle rate (CPH)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

furnaces of over 90% efficiency

9 For electric furnaces

7 Auxiliary heat cycle

rate (CPH)*

Only TH5320U

for 3H/2C Heat Pumps

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

furnaces of over 90% efficiency

9 For electric furnaces

8 Emergency heat cycle

rate (CPH)*

9 For electric emergency heat

1 For steam or gravity systems

furnaces of over 90% efficiency

5 For gas or oil furnaces of less than 90% efficiency



 

� �

System test System status

Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.

Press / to turn system on/off.

Press NEXT to advance to next test.

Press DONE to terminate system test.

Test number System status

press and hold the and

buttons until the display changes

Installer setup

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH5320U/TH5220D or as otherwise noted.

CAUTION: Compressor protection is bypassed during testing. To prevent equipment

�

10 Heating system 0 Heat and fan turn off.

2 Stage 2 heat turns on

TH5320U only

20 Emergency heating

system

0 Heat and fan turn off

1 Heat and fan turn on

2 Stage 2 heat turns on (auxiliary heat) - TH5220D only

30 Cooling system 0 Compressor and fan turn off

1 Compressor and fan turn on

2 Stage 2 compressor turns on

40 Fan system 0 Fan turns off

1 Fan turns on

9 Stage 1 compressor

cycle rate (CPH)

3 Recommended for most compressors

10 Stage 2 compressor

cycle rate (CPH)

3 Recommended for most compressors

12 Manual/Auto

changeover

0 Manual changeover (Heat/Cool/Off)

1 Auto changeover (Heat/Cool/Auto/Off)

2 Auto changeover only (Auto)

14 Temperature

display

0 Fahrenheit

1 Celsius

15 Compressor

protection

5 Five-minute compressor off time

26 Auxiliary heat control 0 Comfort **See page 8

1 Economy

27 Heat temperature

range stops

90 Max. heat temperature setting is 90 °F (32 °C)

28 Cool temperature

range stops

50 Min. cool temperature setting is 50 °F (10 °C)

Installer system test



Honeywell International Inc.

1985 Douglas Drive North

http://customer.honeywell.com

Automation and Control Solutions

® U.S. Registered Trademark.

Honeywell Limited-Honeywell Limitée

Printed in U.S.A. on recycled

paper containing at least 10%

post-consumer paper fibers.

Special function

Auxiliary heat control (Setup Function 26):

Comfort Setting: The thermostat will prioritize comfort over economy depending on heat

pump. Raising the temperature just a few degrees will often activate the auxiliary heat.

Economy Setting: The thermostat will attempt to reach the temperature setting

without activating the auxiliary heat. The thermostat will wait to activate the auxiliary

temperature setting is changed.

Accessories & replacement parts

Please contact your distributor to order replacement parts.

Part Description Part Number Use With

Battery holder 50000951-001 TH5110D

*Use to cover marks left by old thermostats.

Specifications

Temperature Ranges

Operating Ambient Temperature

Shipping Temperature

Operating Relative Humidity

Physical Dimensions

TH5220D

TH5110D

Electrical Ratings

O/B

Andere Handbücher für FocusPRO TH5110D

Dieses Handbuch passt für folgende Modelle

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell T4 Pro Bedienungsanleitung

Honeywell

Honeywell TH8100U1004 Systemhandbuch

Honeywell

Honeywell RTHL2510 series Bedienungsanleitung

Honeywell

Honeywell Round CT87A Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5000 Series Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Bedienungsanleitung

Honeywell

Honeywell Q682B Bedienungsanleitung

Honeywell

Honeywell RTH221B1047 Bedienungsanleitung

Honeywell

Honeywell CT3650 Bedienungsanleitung

Honeywell

Honeywell TH9320WF5003/U Bedienungsanleitung

Honeywell

Honeywell T6812A1000 Bedienungsanleitung

Honeywell

Honeywell WebPAD S7350B Bedienungsanleitung

Honeywell

Honeywell RTH2410B Bedienungsanleitung

Honeywell

Honeywell T8600A-D Bedienungsanleitung

Honeywell

Honeywell RTH2410B1001 Bedienungsanleitung

Honeywell

Honeywell CT3200 series Technische Daten

Honeywell

Honeywell TH9000 Series Bedienungsanleitung

Honeywell

Honeywell PRO TH4110D Bedienungsanleitung

Honeywell

Honeywell T834C Bedienungsanleitung

Honeywell

Honeywell EnergyPro T8665C Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell TB7220U Bedienungsanleitung

Honeywell

Honeywell TB7600 Gebrauchs- und Pflegehandbuch

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung