Honeywell PRO 3000 Bedienungsanleitung

PRO

3000

Series

Non-Programmable

Digital Thermostat

Installation Instructions

Installation

Instructions

Non-Programmable

Digital

Thermostat

Wallplate installation

PULL HERE

HIPS

Remove the wallplate from the

thermostat by pulling from the bottom,

then follow directions below for

mounting.

1. Pull wires through wire hole.

2. Position wallplate on wall, level and

mark hole positions with pencil.

3. Drill holes at marked positions as

shown below, then tap in supplied

wall anchors.

4. Place wallplate over anchors, insert

and tighten mounting screws.

Drill 3/16”

holes for

drywall.

Wire hole

Mounting

screws

Drill 7/32”

holes for

plaster.

Power options

TH3110D

C 24 Vac common. For 2 transformer

systems, use common wire from cooling

transformer.

B Changeover valve energized in heating

R 24 Vac power from heating transformer

Rc 24 Vac power from cooling

transformer

O Changeover valve energized in cooling

G Fan relay

Y Compressor contactor

W Heat relay

TH3210D

C 24 Vac common

B Changeover valve energized in heating

R 24 Vac power

L Sends output when set to Em. Heat

O Changeover valve energized in cooling

G Fan relay

Y Compressor contactor

Aux Auxiliary heat relay

E Emergency heat relay

Wiring terminal designations

TH3110D Terminal block

shown

Connect C for primary AC power

(optional if batteries are installed).

Keep wires in this

shaded

area

Insert batteries for primary

or backup power

Remove factory-

installed jumper only

for two-transformer

systems.

CROGY

BAux L

CROGY

1H/1C Heat Pump System TH3110D [7]

C 24 Vac common [3]

B Changeover valve energized in

heating [5]

R [R+Rc joined by jumper]

Rc Power [1]

O Changeover valve energized in

cooling [5]

G Fan relay

Y Compressor contactor [6]

W [W+Y joined by jumper]

Heat Only System TH3110D

C 24 Vac common [3]

R [R+Rc joined by jumper]

Rc Power [1]

W Heat relay

Heat Only System with Fan TH3110D

C 24 Vac common [3]

R [R+Rc joined by jumper]

Rc Power [1]

G Fan relay

W Heat relay

Cool Only System TH3110D

C 24 Vac common [3]

R [R+Rc joined by jumper]

Rc Power [1]

G Fan relay

Y Compressor contactor

2H/1C Heat Pump System TH3210D

C24 Vac common [3]

B Changeover valve energized in

heating [5]

R Power [1]

L Sends output when set to Em. Heat [8]

O Changeover valve energized in

cooling [5]

G Fan relay

Y Compressor contactor

Aux Auxiliary heat relay [9]

E Emergency heat relay [9]

1H/1C System TH3110D (1 transformer)

C 24 Vac common [3]

R [R+Rc joined by jumper]

Rc Power [1]

G Fan relay

Y Compressor contactor

W Heat relay

1H/1C System TH3110D (2 transformers)

C 24 Vac common [3, 4]

R Power (heating transformer) [1, 2]

Rc Power (cooling transformer) [1, 2]

G Fan relay

Y Compressor contactor

W Heat relay

Wiring conventional and heat pump systems

NOTES

Wire specifications:

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means

and overload protection as required.

[2] Remove jumper for 2-transformer systems.

[3] Optional 24 Vac common connection.

[4] Common connection must come from cool-

ing transformer.

[5] Use either O or B terminals for changeover

valve.

[6] Use a small piece of wire (not supplied) to

connect W and Y terminals.

[7] Set fan operation switch to Heat Pump (see

page 5) and configure system type for heat

pump (see page 6).

[8] L terminal sends a continuous output when

thermostat is set to Em. Heat. Connect

to Honeywell zoning panels to switch the

panel to Emergency Heat.

[9] Install field jumper between Aux and E if

there is no emergency heat relay.

CROGY

BAux L

CROGYW BRc

CROGY

CROGW BRc

CROGY BRc

Thermostat mounting

Set fan operation switch.

Fan operation settings (TH3110D only)

1. Align the 4 tabs on the wallplate

with corresponding slots on the

back of the thermostat.

2. Push gently until the thermostat

snaps in place.

3. Push excess wire back into the

wall opening.

4. Plug wall opening with non-

flammable insulation.

Gas or Oil: For gas or oil heating

systems, leave the fan operation switch

in this factory-set position. (This setting

is for systems that control the fan in a

call for heat.)

Electric or Heat Pump: Change the

switch to this setting for heat pump or

electric heat systems. (This setting is

for systems that allow the thermostat to

control the fan in a call for heat, if a fan

wire is connected to the G terminal.)

Setup

MCR29402

Setup function Settings & options (factory settings in bold)

1 System type

TH3110D only

0 Gas, oil or electric heat with air conditioning

1 Heat pump (5 minute compressor off time in heating and cool-

ing)

5 Heating cycle rate

(CPH: cycles/hour)

TH3110D only

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

6 Auxiliary heat

cycle rate (CPH)

TH3210D only

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

8 Emergency heat

cycle rate (CPH)

TH3210D only

9 For electric emergency heat

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

5 For gas or oil furnaces of less than 90% efficiency

[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

9 Compressor

cycle rate (CPH)

3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5, or 6 CPH]

14 Temperature

display

0 Fahrenheit

1 Celsius

15 Compressor

protection

5 Five-minute compressor off time

[Other options: 0, 1, 2, 3 or 4-minute off time]

Compressor Protection (Setup Function 15): Forces the compressor to wait a few minutes before

restarting, to prevent damage. During the wait time, the message Cool On or Heat On (heat pumps

only) will flash on the display.

Follow the procedure below to configure

the thermostat to match the installed

heating/cooling system, and customize

feature operation as desired.

To begin, press and hold the s and t

buttons until the display changes.

• Press tto change settings.

• Press sto advance to next

function.

• Press and hold ts to exit and

save settings.

Installer Setup

Function

number Setting

Setup

MCR29402

Te st

MCR29403

10 Heating system 0 Heat and fan turn off.

1 Heat turns on.

2 Auxiliary heat turns on (TH3210D only).

20 Emergency heat 0 Heat and fan turn off.

1 Heat and fan turn on.

2 Auxiliary heat turns on.

30 Cooling system 0 Compressor and fan turn off.

1 Compressor and fan turn on.

70 Thermostat information

(for reference only)

71 Software revision number (major revisions)

72 Software revision number (minor revisions)

73 Configuration identification code (major)

74 Configuration identification code (minor)

75 Production configuration date code (week)

76 Production configuration date code (year)

System test System status

}(TH3210D only)

Installer system test

1. Set SYSTEM switch to Heat.

2. Press tto turn on and check

systems (see table, below).

3. Press tuntil systems turn off.

4. Set SYSTEM switch to Em Heat and

repeat steps 2-3 above (TH3210D

only).

5. Set SYSTEM switch to Cool and

repeat steps 2-3 above.

6. Press and hold ts to terminate

test at any time. System switch

Test

MCR29342

System test

number System

status

Troubleshooting

If you have difficulty with your thermostat, please try the following suggestions.

Most problems can be corrected quickly and easily.

Display is

blank

• Check circuit breaker and reset if necessary.

• Make sure power switch at heating & cooling system is

on.

• Make sure furnace door is closed securely.

• Make sure fresh AA alkaline batteries are correctly

installed (see page 2).

Heating

or cooling

system does

not respond

• Set system switch to Heat. Make sure the temperature is

set higher than the Inside temperature.

• Set system switch to Cool. Make sure the temperature is

set lower than the Inside temperature.

• Wait 5 minutes for the system to respond.

Temperature

settings do

not change

Make sure heating and cooling temperatures are set to

acceptable ranges:

• Heat: 40° to 90°F (4.5° to 32°C).

• Cool: 50° to 99°F (10° to 37°C).

“Cool On” or

“Heat On” is

flashing

• Compressor protection feature is engaged. Wait 5

minutes for the system to restart safely, without damage

to the compressor.

“Heat On” is

not displayed

• Set the System switch to Heat, and set the temperature

level above the current room temperature.

“Cool On” is

not displayed

• Set the System switch to Cool, and set the temperature

level below the current room temperature.

Temperature Ranges

Heat: 40° to 90°F (4.5° to 32°C)

Cool: 50° to 99°F (10° to 37°C)

Operating Ambient Temperature

32° to 120°F (0° to 48.9°C)

Shipping Temperature

-20° to 120°F (-28.9° to 48.9°C)

Operating Relative Humidity

5% to 90% (non-condensing)

Physical Dimensions

3-13/16” H x 5-3/8” W x 1-1/4” D

97 mm H x 137 mm W x 32 mm D

Electrical Ratings

System Voltage (50/60Hz) Running Current

Heat (1st stage) 20-30 Vac 0.02-1.0 A

(Powerpile) 750 mV DC 100 mA DC

Emergency heat 20-30 Vac 0.02-1.0 A

Auxiliary heat 20-30 Vac 0.02-1.0 A

Cooling 20-30 Vac 0.02-1.0 A

Specifications

Automation and Control Solutions

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

customer.honeywell.com

® U.S. Registered Trademark.

69-1929EFS—03 M.S. Rev. 04-13

Printed in U.S.A.

69-1929EFS-03

For assistance with this product, please

visit customer.honeywell.com.

Or call Honeywell Customer Care toll-

free at 1-800-468-1502.

Need Help?

Turn thermostat

over to find model

number and date

code.

Pull at bottom

to remove

thermostat

from

wallplate.

CAUTION:

EQUIPMENT DAMAGE HAZARD

Compressor protection is bypassed during testing. To prevent equipment damage, avoid

cycling the compressor quickly.

CAUTION:

ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before beginning

installation.

CAUTION:

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

Non-Programmable

Digital Thermostat

Installation Instructions

PRO

3000Série

Thermostat

numérique non

programmable

Notice

D’installation

PULL HERE

HIPS

Installation de la plaque murale

Séparer la plaque murale du thermostat

comme l’indique l’illustration ci-contre, puis

suivre les directives d’installation.

1. Faire passer les fils par l’ouverture

réservée aux fils.

2. Placer la plaque murale sur le mur,

mettre de niveau et marquer au crayon

l’emplacement des trous.

3. Percer les trous aux endroits marqués à

l’aide d’une perceuse, puis insérer les

chevilles d’ancrage fournies.

4. Apposer la plaque murale sur les

chevilles, insérer puis resserrer les vis de

fixation.

Trou du fil Vis de montage

Utiliser une

mèche de

3/16 po si le

mur est en

placoplâtre

Utiliser une mèche

de 7/32 po si le

mur est en plâtre.

Options d’alimentation

Désignation des bornes

Bornier du TH3110D Raccorder la borne Cpour l’alimentation principale

en c.a. (optionnel si des piles sont installées).

Garder les fils dans

cettezone

ombragée

Insert batteries for primary

or backup power

Retirer le cavalier installé

en usine seulement si

le système est à deux

transformateurs

CROGY

BAux L

CROGY

TH3110D

C Commun 24 V c.a. Dans les systèmes

à deux transformateurs, utiliser le

fil commun du transformateur de

refroidissement.

B Vanne d’inversion déclenchée en mode

de chauffage

R Alimentation 24 V c.a. provenant du

transformateur de chauffage

Rc Alimentation 24 V c.a. provenant du

transformateur de refroidissement

O Vanne d’inversion déclenchée en mode

de refroidissement

G Relais de ventilateur

Y Contacteur du compresseur

W Relais de chauffage

TH3210D

C Commun 24 V c.a.

B Vanne d’inversion déclenchée en mode

de chauffage

R Alimentation 24 V c.a.

L Envoie un signal de sortie lorsque

raccordée au chauffage d’urgence

O Vanne d’inversion déclenchée en mode

de refroidissement

G Relais de ventilateur

Y Contacteur du compresseur

Aux Relais de système de chauffage

auxiliaire

E Relais de système de chauffage

d’urgence

Andere Handbücher für PRO 3000

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell T Series Bedienungsanleitung

Honeywell

Honeywell The Round CT87K Bedienungsanleitung

Honeywell

Honeywell RTH2310 Bedienungsanleitung

Honeywell

Honeywell T8000C Bedienungsanleitung

Honeywell

Honeywell Q539A Bedienungsanleitung

Honeywell

Honeywell CT410A Bedienungsanleitung

Honeywell

Honeywell INNCOM e528 Series Bedienungsanleitung

Honeywell

Honeywell TH2110 Bedienungsanleitung

Honeywell

Honeywell SUNDIAL Y PLAN Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell RLV4300 Bedienungsanleitung

Honeywell

Honeywell Chronotherm III T8602A Bedienungsanleitung

Honeywell

Honeywell TL7230A Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Pro Wi-Fi Bedienungsanleitung

Honeywell

Honeywell TH7000 Series Bedienungsanleitung

Honeywell

Honeywell PROGRAMMABLE THERMOSTAT RTH6350 Bedienungsanleitung

Honeywell

Honeywell Braukmann T104F Bedienungsanleitung

Honeywell

Honeywell DT92E Bedienungsanleitung

Honeywell

Honeywell Chronotherm modulation Bedienungsanleitung

Honeywell

Honeywell T8611G Chmnothern IV Bedienungsanleitung

Honeywell

Honeywell RET97B5D Bedienungsanleitung

Honeywell

Honeywell T1 Pro Bedienungsanleitung

Honeywell

Honeywell TB7300A5014B Bedienungsanleitung

Honeywell

Honeywell PRO TH4110D Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung