Honeywell PRO TH1000 Series Bedienungsanleitung

Installation Manual

Guide d’installation

Guía de instalación

Série PRO TH1000 / TH2000 Series

Programmable and Non-programmable Thermostats

Thermostats programmables et non programmables

Termostatos programables y no programables

ENGLISH

PRO TH1000 / TH2000 Series

Programmable and Non-programmable Thermostats

This manual covers the following models:

System Types

TH1110D and TH1210D

non-programmable thermostats

TH2110D and TH2210D

programmable thermostats

(Remove thermostat from wallplate and turn over to find model number.)

TH1110D and TH2110D:

• Central heating (gas, oil, electric or high-

efficiency furnace)

• Central heating (see above) with air

conditioning

• Hot water system (steam or gravity) with or

without pump

• Central air conditioners

• 750 mV heating systems

• 1-Heat/1-Cool heat pumps

TH1210D and TH2210D:

• 2-Heat/1-Cool heat pumps

Must be installed by a trained, experienced technician

Read these instructions carefully. Failure to follow these instructions

can damage the product or cause a hazardous condition.

Need Help?

For assistance with this product please visit http://yourhome.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502.

Installation Guide

ENGLISH

nLoosen the locking screw at the bottom of the thermostat. Note that the screw is

captive and cannot be removed from the wallplate.

oSeparate the thermostat from the wallplate as per Figure 1.

pPosition the wallplate against the wall and mark hole positions with a pencil.

NOTE: Levelling is for esthetics only and will not affect the performance of the

thermostat.

qDrill holes at the marked positions and insert supplied wall anchors.

rPass the wires through the large opening located at the bottom center of the wallplate

as per Figure 2.

sSecure the wallplate to the wall with supplied mounting screws as per Figure 3.

tConnect the wires to the terminals.

Wallplate installation

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power

before beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube,

do not place the old control in the trash. Contact your local waste

management authority for instructions regarding recycling and proper

disposal.

Figure 1

Figure 2 Figure 3

PRO TH1000 / TH2000 Series

ENGLISH

Gas, oil or electric heating and/or air conditioning (1H / 1C / 1H1C)

Heat pump without auxiliary heating (1H1C)

Heat pump with auxiliary heating (2H1C)

Wiring

Power supply. Provide disconnect means and overload protection as required.

Set the O/B jumper according to the type of reversing valve (see page 4).

Use a piece of wire (not supplied) to connect W and Y terminals to each other.

Optional 24 VAC common connection. If this connection is not made, use batteries

to power the thermostat.

This connection is not required for systems that provide heating only

This connection is not required for systems that provide cooling only

This connection is not required for systems that do have an air recirculating fan.

Use

TH1110D

TH2110D

Fan

Compressor

Heat

Use

TH1110D

TH2110D

Fan

Compressor

Reversing valve

Use

TH1210D

TH2210D

Fan

Compressor

Heat

Reversing valve

Installation Guide

ENGLISH

NOTE: This setting is necessary only if the thermostat is connected to a heat pump.

The jumper is located on the back of the thermostat faceplate. Set it according to the type

of reversing (changeover) valve used by the heat pump.

•O (factory setting): The reversing valve is energized when the System switch is set to

Cool (cooling mode).

•B: The reversing valve is energized when the System switch is set to Heat (heating

mode).

Incorrect jumper setting: The heat pump operation will be reversed; i.e., it will cool in

Heat mode and will heat in Cool mode.

NOTE: This setting is not applicable if a fan is not connected to the G terminal.

The jumper is located on the back of the thermostat faceplate. It determines how the fan

operates when placed in Automatic mode.

•HG (factory setting): Leave the jumper in this position for gas or oil heating systems. In

this position, the heating system controls the fan operation and activates the fan only

when the plenum air is sufficiently warm.

•HE: Place the jumper to this position for heat pump or electric heating systems. In this

position, the thermostat activates the fan only when there is a call for heat.

Incorrect jumper setting: An incorrect setting is noticeable

in a gas or oil heating system.

When heating starts, you will initially feel cold air coming out of the vents as the fan is running

before the furnace has enough time to heat up the air.

If 24 VAC common wire is connected to the C terminal, batteries are

optional and serve to provide backup power.

If 24 VAC common wire is not connected to the C terminal, batteries

are necessary to power the thermostat.

Install 2 AAA batteries on the back of the thermostat faceplate as

shown.

nAlign the two brackets on the top of the thermostat with the

corresponding slots on the top of the wallplate.

oPush the faceplate against the wallplate.

pTighten the screw at the bottom of the thermostat.

Reversing valve setting

Fan operation setting

Battery installation

Thermostat mounting

PRO TH1000 / TH2000 Series

ENGLISH

Follow the procedure below to personalize and

configure the thermostat according to the heating/

cooling system.

nPress Sand Tfor three seconds. The display

will appear as shown on the right.

oPress Sor Tto change the option.

pPress Sand Tfor three seconds to advance to

the next function.

qPress Run to exit the menu and save any

changes.

NOTE

: You will also exit the menu if you press

and

for three seconds when the last function is

displayed.

1Applicable to programmable models (TH2110D & TH2210D) only.

2Damage can occur if the compressor is restarted too soon after shutdown. This feature

forces the compressor to wait 5 minutes before restarting. During the wait time, the

message Cool On or Heat On flashes on the screen. When the safe wait time has elapsed,

the message stops flashing and the compressor turns on.

3Applicable to programmable models (TH2110D & TH2210D) only.

Adaptive Intelligent Recovery™ allows the thermostat to “learn” how long your furnace or

air conditioner takes to reach the set temperature. Simply program the desired times and

desired temperatures into the schedule. The thermostat will determine when to activate

heating or cooling so that the desired temperature is attained at the desired time.

Installer setup

Function Default

setting Options

1 Temperature display format 0 0: Fahrenheit

1: Celsius

2Time display format100: 12-hour display

1: 24-hour display

3 Heating cycles per hour 5

2 to 6 cycles per hour

• 2: 30 min (steam, gravity)

• 3: 20 min (hot water, 90%+ high-efficiency furnace)

• 4: 15 min (gas or oil)

• 5: 12 min (gas or oil)

• 6: 10 min (electric)

4 Cooling cycles per hour 3 2 to 6 cycles per hour

5Compressor protection200: enabled (for systems without a compressor))

1: disabled (for systems equipped with a compressor)

6Adaptive Intelligent Recovery310: Off

1: On

Function

number

Option

number

Installation Guide

ENGLISH

Temperature Ranges

• Heat: 40 °F to 90 °F (4.5 °C to 32 °C)

• Cool: 50 °F to 99 °F (10 °C to 37 °C)

Operating Ambient Temperature

• 32 °F to 122 °F (0 °C to 50 °C)

Shipping Temperature

• -40 °F to 130 °F (-40 °C to 55 °C)

Operating Relative Humidity

• 5% to 90% (non-condensing)

Physical Dimensions

• 4.7” H x 2.9” W x 1.1” D (120 mm H x 74 mm W x 28 mm D)

Power Supply

• 24 VAC or 2 AAA batteries

Maximum Load

• 1 A @ 24 VAC per output

Specifications

FRANÇAIS

Série PRO TH1000 / TH2000

Thermostats programmables et non programmables

Le présent guide porte sur les modèles suivants :

Types de système

Thermostats non programmables

TH1110D et TH1210D

Thermostats programmables

TH2110D et TH2210D

(Retirer le thermostat de la plaque murale et le retourner pour voir le numéro de modèle.)

TH1110D et TH2110D :

• Chauffage central (fournaise au gaz, mazout,

électrique ou à haut rendement)

• Chauffage central (voir ci-dessus) avec

climatisation

• Eau chaude (vapeur ou gravité) avec ou sans

pompe

• Climatiseur centrale

• Systèmes de chauffage 750 mV

• Thermopompes à 1 étage de chauffage / 1

étage de refroidissement

TH1210D et TH2210D :

• Thermopompes à 2 étages de chauffage / 1

étage de refroidissement

Doit être installé par un technicien d’expérience ayant reçu la formation pertinente.

Lire attentivement les instructions. Le fait de ne pas les suivre

risque d’endommager le produit ou de présenter un danger.

Besoin d’aide?

Pour obtenir de l’assistance au sujet de ce produit, consulter le

http://yourhome.honeywell.co

ou téléphoner sans frais au Centre de service à la clientèle de Honeywell au

1 800 468-1502

Guide d’utilisation

FRANÇAIS

nDesserrer la vis de blocage au bas du thermostat. Noter que la vis est captive et ne

peut pas être enlevée de la plaque murale.

oSéparer le thermostat de la plaque murale selon la figure 1.

pPlacer la plaque murale contre le mur et marquer au crayon l’emplacement des trous.

NOTA : La mise à niveau est pour l’esthétique uniquement et n'affectera pas le

fonctionnement du thermostat

qPercer les trous aux endroits marqués et insérer les chevilles d’ancrage fournies.

rPasser les fils par la grande ouverture située au centre inférieur de la plaque murale

selon la figure 2.

sFixer la plaque murale au mur avec les vis de montage fournies selon la figure 3.

tRelier les fils aux bornes.

Installation de la plaque murale

MISE EN GARDE : RISQUE DE CHOC ÉLECTRIQUE

Peut provoquer des chocs électriques ou endommager le matériel. Couper

l’alimentation électrique avant d’effectuer le raccordement.

AVIS SUR LE MERCURE

Si le nouveau thermostat remplace un ancien régulateur contenant un

contact à mercure, ne pas jeter l’ancien régulateur aux poubelles.

Communiquer avec le service local de cueillette des déchets pour obtenir

de l’information sur le recyclage ou sur la bonne façon de disposer d’un

ancien régulateur contenant un contact à mercure.

Figure 1

Figure 2 Figure 3

Andere Handbücher für PRO TH1000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell T8000 Bedienungsanleitung

Honeywell

Honeywell DT70 Series Bedienungsanleitung

Honeywell

Honeywell INTELLIGUARD 9000 Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell TRADELINE T834C1137 Bedienungsanleitung

Honeywell

Honeywell TH8100U1004 Systemhandbuch

Honeywell

Honeywell 8161 Bedienungsanleitung

Honeywell

Honeywell CHRONOTHERM III T8611G Bedienungsanleitung

Honeywell

Honeywell T7100D Bedienungsanleitung

Honeywell

Honeywell RLV4300 Bedienungsanleitung

Honeywell

Honeywell RTH7400 series Bedienungsanleitung

Honeywell

Honeywell VFD CORE Bedienungsanleitung

Honeywell

Honeywell T9 Bedienungsanleitung

Honeywell

Honeywell CM907 Bedienungsanleitung

Honeywell

Honeywell Chronotherm T4600 Bedienungsanleitung

Honeywell

Honeywell FocusPRO Bedienungsanleitung

Honeywell

Honeywell PRESTIGE THX9321 Benutzerhandbuch

Honeywell

Honeywell TC300 Bedienungsanleitung

Honeywell

Honeywell RTH4300B Bedienungsanleitung

Honeywell

Honeywell RTH5100B1009 Bedienungsanleitung

Honeywell

Honeywell T834C Bedienungsanleitung

Honeywell

Honeywell T921A Bedienungsanleitung

Honeywell

Honeywell EASY-TO-SEE T87N Bedienungsanleitung

Honeywell

Honeywell Chronotherm IV T8602C Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung