Honeywell RTH2300 series Bedienungsanleitung

RTH2300/RTH221

Programmable Thermostat

Quick Installation Guide

69-2448ES-03

69-2448ES—03 ii

Quick Installation Guide

Identify System Type

This thermostat is compatible with the following systems:

Gas, oil or electric furnace•

Central air conditioner•

Hot water system with or without pump•

Millivolt system•

Central heating and cooling system•

Heat pump without auxiliary/backup heat•

Do you need assistance?

We are here to help.

Call 1-800-468-1502.

This thermostat cannot be used on heat pumps with

auxiliary/backup heat or on multistage systems.

1 69-2448ES—03

RTH2300/RTH221

1Turn Off Power to Heating/

Cooling System

M28097

69-2448ES—03 2

Quick Installation Guide

Remove Old Thermostat

M28099

Old thermostat

Cover

Remove old thermostat but leave wallplate with

wires attached.

Do not remove

wallplate yet

MERCURY NOTICE

Do not put your old thermostat

in the trash if it contains

mercury in a sealed tube.

Contact your local waste

management authority for

instructions regarding recycling

and proper disposal.

3 69-2448ES—03

RTH2300/RTH221

If any wires are not attached to your old thermostat or are

attached to a terminal marked Cor C1, they will not be

connected to your new thermostat. Wrap the bare metal

end of each of these wires with electrical tape, so it can-

not touch and short other wires.

Identify Wires

M29988

Disconnect wires and remove the old wallplate only after

all wires are labeled. Wrap the wires around a pencil to

prevent them from falling though the wall opening.

Do not use non-connected

wires.

Do not use C or C1 wires.

Identify and label each wire.

IGNORE WIRE COLORS:

Use terminal screw

designations to identify

wires.

69-2448ES—03 4

Quick Installation Guide

Mount New Wallplate

Loosen the locking screw at the bottom of the1. thermostat. Note that the screw is captive and cannot

be removed from the wallplate.

Separate the thermostat from the wallplate as per2. Figure 1.

Position the wallplate against the wall and mark hole3. positions with a pencil.

NOTE: Levelling is for esthetics only and will not affect

the performance of the thermostat.

Drill holes at the marked positions and insert supplied4. wall anchors.

Pass the wires through the large opening located at5. the bottom center of the wallplate as per Figure 2.

Secure the wallplate to the wall with supplied mounting6. screws as per Figure 3.

Connect the wires to the terminals.7.

Figure 1 Figure 2 Figure 3

M32154

5 69-2448ES—03

RTH2300/RTH221

Connect Wires (typical wiring)

Loosen the terminal screws using a screwdriver, insert2. the wires, then tighten the screws.

Push any excess wire back into the wall opening.3.

Labels don’t match?

If a wire does not match any terminal designation, see next page.

Match each labeled wire with the terminal having the1. same letter.

O/B Y RC R G W

M32155

REMOVE JUMPER

IF YOU HAVE BOTH

RAND RC WIRES

69-2448ES—03 6

Quick Installation Guide

Connect Wires (alternate wiring)

If labeled wire does not match any terminal designation, see

diagram below.

M32169A

REMOVE JUMPER BETWEEN RAND RC IF YOU HAVE

WIRES ON BOTH RAND RC.

DO NOT USE C, C1, OR X WIRE. DO NOT USE B WIRE

IF YOU ALREADY HAVE 0 WIRE. WRAP BARE END OF

WIRE WITH ELECTRICAL TAPE.

PLACE A JUMPER (PIECE OF WIRE) BETWEEN Y AND

W IF YOU ARE USING A HEAT PUMP WITHOUT

AUXILIARY/BACKUP HEAT.

O/B Y RC R G W

2 33 1

7 69-2448ES—03

RTH2300/RTH221

Set jumper JP1, on the back of the thermostat, if you

have connected a wire to the G terminal.

Set Heating Fan Control

HG Leave the jumper in this factory-set position if

you have a gas or oil furnace.

HE Place the jumper to this position if you have

an electric furnace.

Incorrect jumper setting: An incorrect setting is notice-

able in a gas or oil heating system. When heating starts,

you will initially feel cold air coming out of the vents as

the fan is running before the furnace has enough time to

heat up the air.

JP1

69-2448ES—03 8

Quick Installation Guide

Set jumper JP2, on the back of the thermostat, if you

have a heat pump.

Set Heat Pump Reversing Valve

O Leave the jumper in this factory-set position if

you have connected O wire to the O/B terminal.

B Place the jumper to this position if you have

connected B wire to the O/B terminal.

Incorrect jumper setting: The heat pump operation will

be reversed, i.e., it will cool in Heat mode and will heat in

Cool mode.

JP2

Andere Handbücher für RTH2300 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell RTH6400 Series Bedienungsanleitung

Honeywell

Honeywell L641A Bedienungsanleitung

Honeywell

Honeywell T4360G Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell Q682B Bedienungsanleitung

Honeywell

Honeywell T10 Pro Smart Bedienungsanleitung

Honeywell

Honeywell T8501D Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell T7200 Bedienungsanleitung

Honeywell

Honeywell T8700B Bedienungsanleitung

Honeywell

Honeywell 69-0568 Bedienungsanleitung

Honeywell

Honeywell TB7300A5014B Bedienungsanleitung

Honeywell

Honeywell INNCOM e7w Bedienungsanleitung

Honeywell

Honeywell DG115EZIAQ - TrueIAQ Digital IAQ Control Bedienungsanleitung

Honeywell

Honeywell lyric round Bedienungsanleitung

Honeywell

Honeywell RTH3100C Bedienungsanleitung

Honeywell

Honeywell Digital Round T8775C Bedienungsanleitung

Honeywell

Honeywell TB3 Series Bedienungsanleitung

Honeywell

Honeywell TH401 Bedienungsanleitung

Honeywell

Honeywell T4800A Bedienungsanleitung

Honeywell

Honeywell T641A Bedienungsanleitung

Honeywell

Honeywell RLV430 Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung