Honeywell RTH5100B Bedienungsanleitung

Owner’s Manual

Read and save these

instructions.

For help please visit

yourhome.honeywell.com

RTH5100B

Non-Programmable

Digital Thermostat

Installation is Easy

1. Label wires and remove your old thermostat

2. Install and wire your new thermostat

3. Set your new thermostat to match your heating/cooling system

• It is preset for the most common system

Do you need assistance? We are here to help.

Call 1-800-468-1502 for wiring assistance before returning

the thermostat to the store.

This thermostat works on 24 volt or 750 mV systems.

It will NOT work on multi-stage heat pump systems or

120/240 Volt systems.

NOTICE: To avoid possible compressor damage, do not run air

conditioner if the outside temperature drops below 50°F (10°C).

ATTENTION: MERCURY RECYCLING NOTICE

This product does not contain mercury. However,

this product may replace a product that contains

mercury. Mercury and products containing

mercury should not be discarded in household

trash.

For more information on how and where to

properly recycle a thermostat containing

mercury in the United States, please refer to the

Thermostat Recycling Corporation at

www.thermostat-recycle.org.

For mercury thermostat recycling in Canada,

please refer to Switch the Stat at

www.switchthestat.ca

NO MERCUR

NE PAS JETER

LE MERCURE

M28300

Customer assistance

For assistance with this product, please visit

http://yourhome.honeywell.com.

Or call Honeywell Customer Care toll-free at

1-800-468-1502.

To save time, please note your model number

and date code before calling.

Remove battery holder; model number is on

the battery holder.

® U.S. Registered Trademark. Patents pending.

US Patent No. D535,573 and other patents pending.

Installation

Installation............................................3

Advanced Installation...........................7

About your new thermostat

Controls and Home screen

quick reference.....................................9

Compressor protection.......................12

Replace batteries...............................12

Appendices

Troubleshooting..................................13

Limited warranty.................................14

Table of contents

1 Turn Off Power to Heating/Cooling System

M31535

Circuit breaker

box Heating/cooling system

power switch

2 Remove Old Thermostat

Remove old thermostat but leave wallplate with wires attached.

Do not remove wallplate yet

MCR33823

Terminal

designation

If you have an older thermostat with a

sealed mercury tube, turn to page 2

for proper disposal instructions.

3 Label Wires with Tags

Label the wires using the supplied wire labels as you disconnect them.

M28100

5 Mount Wallplate

Mount the new wallplate using the included screws and anchors.

Drill 3/16-in. holes for drywall

Drill 3/32-in. holes for plaster

MCR29533

4 Separate Wallplate from New Thermostat

Remove wallplate from the new thermostat and mount onto wall.

M29532

Wallplate

Wire Labels

Terminal designation

MCR31537

Remove metal

jumper if you

have both Rand

Rc wires.

MCR29534

Thermostat does not work on Heat Pumps with auxiliary/backup heat.

We are here to help. Call 1-800-468-1502 for wiring assistance.

6 Connect Wires

Simply match wire labels.

If labels do not match letters on the thermostat, check “Alternate Wiring” on

page 5 and connect to terminal as shown (see notes, below).

Alternate Wiring

If wires will be connected to both

Rand Rc terminals, remove metal

jumper

Do not connect both Oand B, If

you have a heat pump. Connect

O wire to O/B W. Wrap B wire with

electrical tape and do not use.

Do not use C, X or B. Wrap bare

end of wire with electrical tape.

NOT

USED

O/B W

NOT

CONNECT

MCR29548

OR R

OR RH 4V

OR Y1 M

OR W1 H O

OR F

OR X B

7 Install Batteries

Install two AAA alkaline batteries.

8 Install Thermostat onto

Wallplate

Install thermostat onto the wallplate on

the wall.

Back of thermostat

MCR29535

MCR29536

M31544

Circuit breaker box Heating/cooling system

power switch

9 Turn Power Back On

Turn the power back on to the

heating/cooling system.

10 If your system type is...

If your system type is:

qSingle Stage Heat and Cool

Congratulations, you’re done!

If your system type is:

qHeat Pump* without Backup Heat

qHeat Only

Continue with Advanced Installation to match your thermostat to your system

type.

*Heat Pump—an air conditioner that provides cooling in the summer, and also

runs in reverse in the winter to provide heating.

If you are not sure of your system type or if you have other

questions, call us toll-free at 1-800-468-1502.

This thermostat works on 24 volt or 750 mV systems. It will NOT work on multi-

stage heat pump systems or 120/240 Volt systems.

Advanced Installation

Enter System Setup

To enter system setup, press and hold both

the sand FAN buttons until the display

changes (approximately 5 seconds).

Changing Settings

1. Press the sor tbutton to change the

setting.

2. Press NEXT to advance to the next

function.

3. Press DONE to exit and save settings.

MCR29537

Function Setting

Done

MCR29538

Function

Description

Press the sor tbutton to Setting

1 select the type of system you

have in your home

0 Heating and cooling: Gas, oil or electric heating with

central air conditioning.

1 Heat pump: Outside compressor provides both heating

and cooling.

2 Heating only: Gas, oil or electric heating without central

air conditioning.

3 Heating only with fan: Gas, oil or electric heating

without central air conditioning. (Use this setting if you

could turn the fan on and off with a fan switch on your

old thermostat.)

2 select whether your

changeover valve is used in

heating or cooling

0 Cooling changeover valve: Use this setting if you

connected a wire labeled “O” to the O/B W wire terminal.

1 Heating changeover valve: Use this setting if you

connected a wire labeled “B” to the O/B W wire terminal.

3 select your heating system

and fan operation

0 Gas or oil heat: Use this setting if you have a gas or oil

heating system (system controls fan operation).

1 Electric heat: Use this setting if you have an electric

heating system (thermostat controls fan operation).

5 select your heating system

and optimize its operation

5 Gas or oil furnace: Use this setting if you have a

standard gas or oil furnace that is less than 90%

efcient.

9 Electric furnace: Use this setting if you have any type

of electric heating system.

3 Hot water or high-efficiency furnace: Use this setting

if you have a hot water system or a gas furnace of

greater than 90% efciency.

1 Gas/oil steam or gravity system: Use this setting if

you have a steam or gravity heat system.

12 select Manual or Auto

Changeover

0 Manual Changeover: (Heat/Off/Cool)

1 Automatic Changeover: (Heat/Off/Cool/Auto)

Automatically turns on heat or cool based on room

temperature.

CAUTION: To avoid possible compressor

damage, do not use Auto Changeover if the

outside temperature drops below 50 ºF (10 ºC).

NOTE: System maintains a minimum 3 ºF

difference between heat and cool settings.

14 select Fahrenheit or Celsius

temperature display

0 Fahrenheit temperature display (°F)

1 Celsius temperature display (°C)

27 select maximum heat

temperature setting

40 – 90 Maximum heat temperature setting (°F)

(4.5 to 31.5°C)

28 select minimum cool

temperature setting

50 – 99 Minimum cool temperature setting (°F)

(10.5 to 37°C)

Thermostat controls

M28301

Digital display Battery holder

Temperature buttons

Press to adjust

temperature settings.

Function buttons

Press to select the function displayed just above each button.

(Functions change depending on the task.)

About your new thermostat

Your new Honeywell thermostat has been designed to give you many years of

reliable service and easy-to-use, push-button climate control.

• Large, clear, backlit display is easy to read — even in the dark.

• Displays both room temperature and temperature setting.

• Removable battery holder for fast, easy replacement.

• Built-in compressor protection.

System

Cool

Cool On

Setting

Cool

Inside

Auto

Fan

M28305

Adjust the temperature

Press sor tto adjust the

temperature.

NOTE: Make sure the thermostat

is set to the system you want to

control (heat or cool).

Display screen

System

Cool

Cool On

Setting

Cool

Inside

Auto

Fan

M28302

Current inside temperature Temperature setting

System status

Indicates system is on.

(Cool On or Heat On.)

System setting

Press the SYSTEM

button to select Heat,

Cool or Off.

Fan setting

Press the FAN button to

select Auto or On.

In “Auto” mode (the most

commonly used setting), the fan

runs only when the heating or

cooling system is on. If set to “On,”

the fan runs continuously.

• Heat: Thermostat controls only the heating

system.

• Cool: Thermostat controls only the cooling

system.

• Auto: Thermostat automatically selects

heating or cooling depending on the

indoor temperature.

• Off: Heating and cooling systems are off.

Andere Handbücher für RTH5100B

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell FTSE20 Bedienungsanleitung

Honeywell

Honeywell T8601D Bedienungsanleitung

Honeywell

Honeywell T834C Bedienungsanleitung

Honeywell

Honeywell TB7300A5014B Bedienungsanleitung

Honeywell

Honeywell RTHL2510 series Bedienungsanleitung

Honeywell

Honeywell T7200 Bedienungsanleitung

Honeywell

Honeywell Q539A Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Bedienungsanleitung

Honeywell

Honeywell RTH8500 Series Bedienungsanleitung

Honeywell

Honeywell TL6120 Bedienungsanleitung

Honeywell

Honeywell T8131A Bedienungsanleitung

Honeywell

Honeywell Chronotherm T4600 Bedienungsanleitung

Honeywell

Honeywell T87F Bedienungsanleitung

Honeywell

Honeywell VisionPRO TH8000 Series Bedienungsanleitung

Honeywell

Honeywell Tradeline T8611M Bedienungsanleitung

Honeywell

Honeywell RTH7500D Bedienungsanleitung

Honeywell

Honeywell RTH9585 Wi-Fi Bedienungsanleitung

Honeywell

Honeywell DTS92A Bedienungsanleitung

Honeywell

Honeywell TROL-A-TEMP 69-1496 Bedienungsanleitung

Honeywell

Honeywell T87F Montageanleitung

Honeywell

Honeywell Digital Round T8775C Bedienungsanleitung

Honeywell

Honeywell 69-1402M Bedienungsanleitung

Honeywell

Honeywell Lyric T5 Wi-Fi Bedienungsanleitung

Honeywell

Honeywell T834C Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung