Honeywell T8000 Bedienungsanleitung

X-XX UL

INSTALLATION INSTRUCTIONS

®U.S. Registered Trademark

T8000, T8001

Programmable Thermostat

APPLICATION

The T8000, T8001 Thermostats provide single-stage,

programmable temperature control for 24 Vac heating-

cooling systems with manual changeover from heat to

cool. Heating cycle rate is selectable at 1, 3, 4, 5, 6, 9, or

12 cph. Cooling cycle rate is fixed at 3 cph. Temperature

indication can be set for °F or °C.

The T8001 Thermostat is powered directly from the

system transformer. The T8000 Thermostat is powered

through the heating/cooling system controls. Batteries are

not required because setpoints are held permanently by

non-volatile memory.

The T8000 and T8001 include a thermostat, wallplate and

owner’s guide. A 7 3/8 in. (188 mm) x 5 3/4 in. (146 mm)

decorator cover plate (for covering wall marks) is available

separately. Order Honeywell part no. 209649A (taupe) or

part no. 209649B (white).

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of it properly.

Contact your local waste management authority for

instructions regarding recycling and the proper

disposal of a control.

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-

ous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

Hazardous Voltage.

Can damage heating/cooling system.

Disconnect power at furnace or main breaker/

fuse box.

Location

Install the thermostat about 5 ft (1.5m) above the floor in

an area with good air circulation at average temperature.

See Fig. 1. Do not install the thermostat where it can be

affected by:

—drafts or dead spots behind doors and in corners.

—hot or cold air from ducts.

—radiant heat from the sun or appliances.

—concealed pipes and chimneys.

—unheated (uncooled) areas such as an outside wall

behind the thermostat.

Mounting Wallplate to Wall

IMPORTANT

Level only for appearance. The thermostat

functions normally even when not level.

Mount wallplate and the thermostat with the screws

provided (see Fig. 2) as follows:

1. Place the wallplate at the desired location on the

wall.

2. Pull the thermostat wire through the wallplate

entrance hole.

3. Fasten the wallplate to the wall using the anchors

and screws provided.

4. After wiring the wallplate, plug the hole with non-

flammable insulation to prevent drafts from affecting

the thermostat; see Wiring section.

Table 1. Description of Thermostats.

Model System Changeover System Selection Fan Selection Powering Method

T8001 Heat-Cool Manual Cool-Off-Heat Auto-On Hardwired

T8000 Heat-Cool Manual Cool-Off-Heat Auto-On Power Stealing

69-1432-1

69-1432-1 2

T8000, T8001 PROGRAMMABLE THERMOSTAT

Fig. 1. Typical location of thermostat.

5 FEET

[1.5 METERS]

YES

M11338

M12202

WALL WALL

ANCHORS (2)

WALLPLATE

MOUNTING

SCREWS (2)

Fig. 2. Mounting wallplate to wall.

Wiring

IMPORTANT

Use an 18-gauge maximum wire for wiring the

thermostat.

All wiring must comply with local electrical codes and

ordinances. Disconnect the power supply to prevent

electrical shock or equipment damage.

The shape of the terminals permits insertion of straight or

wraparound wiring connections; either method is accept-

able. A letter code is located near each terminal for

identification. See Fig. 3.

NOTE: To ensure proper mounting of thermostat, restrict

all wiring to the shaded area in the center of the

terminals. See Fig. 4.

TERMINAL

CREW

M12564

FOR STRAIGHT

INSERTION STRIP

5/16 IN. (8 MM)

FOR WRAPAROUND

STRIP 7/16 IN. (11 MM

)

Fig. 3. Wiring connections.

69-1432-1

T8000, T8001 PROGRAMMABLE THERMOSTAT

KEEP WIRING IN

SHADED AREA

MOUNTING

SCREW HOLE MOUNTING

SCREW HOLE

WIRING ENTRANCE

HOLE

M12565

Fig. 4. Restrict wiring to shaded area.

The T8001 Thermostat is powered directly from the

system transformer and is adaptable to most 18 to 30 Vac

heating-cooling systems. All T8001 Thermostats require a

common wire to supply power. Refer to Fig. 5 - 8 for

typical wiring hookups.

(HOT)

M12566

FAN

RELAY

HEAT

RELAY

COMPRESSOR

CONTACTOR

TRANSFORMER

HEAT

DAMPER

COOL

DAMPER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT

PUMP SYSTEMS.

T8001 THERMOSTAT

Fig. 5. Typical hookup of T8001 in heat-cool system

with one transformer.

Fig. 6. Typical wiring diagram for T8001 on a zone 1

MABS II or Masterol™ control panel.

Fig. 7. Typical wiring diagram for T8000 in heat-cool

system with one transformers.

M12562

(HOT

)

FAN

RELAY

HEAT

RELAY

(HOT)

COMPRESSOR

CONTACTOR

HEATING

TRANSFORMER

COOLING

TRANSFORMER

HEAT

DAMPER

COOL

DAMPER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

REMOVE RC TO R JUMPER WHEN INSTALLED ON A TWO TRANSFORMER

SYSTEM.

CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT

PUMP SYSTEMS.

POWER TO R TERMINAL IS REQUIRED WHEN THE SYSTEM SWITCH IS IN

THE OFF POSITION.

(HOT)

M12561

FAN

RELAY

T8000C THERMOSTAT

COMPRESSOR

CONTACTOR

TRANSFORMER

COOL

DAMPER

1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT

PUMP SYSTEMS.

JUMPER R TO Rc.

HEAT

RELAY

HEAT

DAMPER

ZONE

HANGEOVER

ONTROL

M12567

T8001 THERMOSTAT

Fig. 8. Typical wiring diagram for T8000 in heat-cool

system with two transformers.

69-1432-1 4

T8000, T8001 PROGRAMMABLE THERMOSTAT

Fig. 9. Mounting thermostat to wallplate.

Mounting Thermostat to Wallplate

1. Slide SYSTEM switch to the Off position.

2. Engage the tabs at the top of the thermostat and

wallplate.

3. Swing down the thermostat and press the lower

edge of the thermostat onto the wallplate to latch.

See Fig. 9.

INSTALLER SETUP

Setting °F/°C Indication and

Heat Cycle Rate

The following instructions provide the information neces-

sary to change the heating cycle rate to match the heating

equipment and to choose either Fahrenheit (°F) or Celsius

(°C) display.

NOTE: All four steps must be completed to save

changes to the °F/°C indication and the heat

cycle rate.

1. Enter Installer Setup.

a. Use ▲or ▼keys

to set the tempera-

ture setpoint to

52°F (11°C).

b. Press the ▲and ▼keys simultaneously for

more than two seconds to enter installer

setup.

c. When released,

the three-digit

software revision

code is displayed.

d. Press the ▲key.

Factory

configuration

(FC) is displayed

(A typical

example is

shown, but

information displayed varies by

model. This information is for factory use

only).

Optional System Checkout

When in steps 1c and 1d only, pressing the ▼key can be

used to turn heat or cool outputs on and off. Change the

SYSTEM switch setting to test heat or cool outputs. No

action takes place If the system switch is in the Off

position.

Examples: System setting at HEAT: If heat is on,

pressing the ▼key turns it off; if heat is off,

pressing the ▼key turns it on.

System setting at COOL: If cool is on,

pressing the ▼key turns it off; if cool is off,

pressing the ▼key turns it on. The 5 minute

minimum off time is bypassed.

M12582

SET

HT.

M12583

M12584

M1467

DASHED LINES INDICATETABS

ON BACK OFTHERMOSTAT

ENGAGE TABS AT TOP OF THERMOSTAT

WITH SLOTS ON WALLPLATE.

PRESS LOWER EDGE OF

CASE TO LATCH.

SYSTEM

Cool Off Heat

Auto On

FAN

Hold

Select

SYSTEM

Cool Off Heat

Auto On

FAN

Hold

Select

TUE

M1258

FAN OPERATION (FUEL) SWITCH

Setting Fan Operation (Fuel) Switch

The fan operation (fuel) switch is preset at the factory in

the F position. See Fig. 9. This is the correct setting for

most systems. If this system is an electric heat system, set

the switch to the E position. The E setting allows the fan to

turn on immediately with the heating or cooling equipment

in a system where the G terminal is connected.

Fig. 8. Fan operation (fuel) switch.

69-1432-1

T8000, T8001 PROGRAMMABLE THERMOSTAT

NOTE: In installer setup only, each press of the ▲key

momentarily displays 1. Each press of the ▼key

momentarily displays 2. When the keys are

released, these one-digit codes are no longer

displayed.

2. Setting °C or °F.

a. Press the ▲key

again to display

the current setting.

b. Press the ▼key to

change the °C or

°F indication.

3. Setting Heat Cycle Rate

(see Table 2 for the cycle rate options and equip-

ment).

a. Press the ▲key

to display the

current heat

cycle rate setting

of 1, 3, 4, 5, 6, 9,

or 12 cph.

b. If the desired cycle rate is displayed, press the

▲key to exit the installer setup.

c. To change the

heat cycle rate,

press the ▼key

until your choice of

1, 3, 4, 5, 6, 9, or

12 is displayed.

d. Press the ▲key to

display cooling

algorithm configu-

ration default.

e. Press the ▲key

again to change

cooling algorithm to C1 or C3.

C1 = Standard cooling algorithm.

C3 = Agressive cooling algorithm (can

cause overshooting).

f. Press the ▲key again. Current configuration

(CC) is displayed. A typical example is shown,

but CC varies by

model. (This

information is for

factory use only.)

4. Exit Installer

Setup.

a. Press

the ▲

key to

save all

changes

and return to normal operation.

Table 2. Heating Cycle Rate

M12586

M12587

M12588

M12589

M12590A

OPERATION

Setting FAN and SYSTEM Switches

Fan and system settings are controlled manually by using

the switches located at the bottom of the thermostat case.

See Fig. 11.

FAN Switch

Fan switch settings are:

On: The fan runs continuously. Use for improved air

circulation and air quality.

Auto: Normal setting for most homes. In cooling, the fan

starts and stops with the cooling equipment. In

heating, the fan is controlled directly by the heating

equipment and may start a few minutes after the

heating equipment turns on (most systems). When

the fan operation (fuel) switch is in the E position,

the fan starts and stops with the heating equipment.

Slide the FAN switch in the lower left corner of the

thermostat to select the desired fan setting.

SYSTEM Switch

System switch settings control thermostat operation as

follows:

Cool: The thermostat controls the cooling system.

Off: Both heating and cooling are off.

Heat: The thermostat controls the heating system.

Slide the SYSTEM switch in the lower right corner of the

thermostat to select the desired system setting.

System Cycles Per Hour

Steam, Gravity 1

Hydronic Heat, Condensing

Gas Furnaces

Gas or Oil Forced Air 6

Electric Heat 9

Special Applications

High efficiency furnace (90+).

Refer to the equipment manufacturer’s Instructions.

M1469

SYSTEM

Cool Off Heat

Auto On

FAN

M14693

Hold

Select

TUE

4, 5, 12

Fig. 11. Digital Display and System Switches.

69-1432-1 6

T8000, T8001 PROGRAMMABLE THERMOSTAT

69-1432-1 G.H. Rev. 2-02 Printed in U.S.A.

CHECKOUT

Heating

1. Slide the SYSTEM switch to Heat and the FAN

switch to Auto.

2. Press and hold the ▲key to raise the temperature

setting several degrees above the room tempera-

ture; the heating equipment should start. In conven-

tional systems, the system turns on the fan through

the use of a time delay relay or through a limit

control. When the fan operation (fuel) switch is in the

E position, the fan starts immediately.

3. Press the ▼key to lower the temperature setting

below the room temperature. Heating equipment

should stop.

Cooling

CAUTION

Damage To compressor possible.

Operating at too low of an outdoor temperature

may cause compressor damage.

Do not operate cooling if outdoor temperature is

below 50°F (10°C).

Allow compressor to remain off for five minutes

before restarting.

Refer to manufacturer’s recommendations.

1. Slide the SYSTEM switch to Cool and the FAN

switch to Auto.

2. Press the ▼key to lower the temperature setting

several degrees below the room temperature; the

cooling equipment should start. The fan starts and

stops with the cooling equipment.

NOTE: If unit doesn’t start immediately, remember,

the thermostat has a built-in minimum

off-time of five minutes to protect the

compressor.

3. Press the ▲key to raise the temperature setting

above the room temperature. Cooling system should

shut down.

Fan

1. Slide the SYSTEM switch to Off and the FAN switch

to On. The fan should run continuously.

2. Slide the FAN switch to Auto. In heating, the fan is

controlled directly by the heating equipment and

may start a few minutes after the heating equipment

turns on (on most systems). When the fan operation

(fuel) switch is in the E position, the fan starts and

stops with the heating equipment. In cooling, the fan

starts and stops with the cooling equipment.

Make certain all equipment responds correctly to the

thermostat.

Period Time Heat Setpoint Cool Setpoint

Wake 6:00 AM 70°F (21°C) 78°F (26°C)

Leave 8:00 AM 62°F (17°C) 85°F (29°C)

Return 6:00 PM 70°F (21°C) 78°F (27°C)

Sleep 10:00 PM 62°F (17°C) 82°F (28°C)

Honeywell Limited-Honeywell Limitée

35 Dynamic Drive

Scarborough, Ontario

M1V 4Z9

Automation and Control Solutions

Honeywell

1985 Douglas Drive North

Golden Valley, MN 55422

www.honeywell.com/yourhome

M12591

SET

M12592

SET

M12593

M12594

Setting Current Time and Day

1. To Set Current Time.

a. Press Select twice.

b. Press ▲or ▼to

set current time.

2. To Set Day of Week.

a. Press Select

again.

b. Press ▲or ▼to

set current day.

To use the preprogrammed time and temperature (see

Table 3) press Hold to exit the programming mode.

Setting Time and Temperature

The T8001C is preprogrammed with the time and tem-

perature settings shown in Table 3. For instructions on

programming the thermostat refer to the Owners Guide,

Form No. 69-1143.

Table 3. Preprogrammed Time and

Temperature Settings.

Andere Handbücher für T8000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell RTH2510 Series Bedienungsanleitung

Honeywell

Honeywell RLV3100 Bedienungsanleitung

Honeywell

Honeywell INTELLIGUARD 9000 Bedienungsanleitung

Honeywell

Honeywell PRO TH4000 series Bedienungsanleitung

Honeywell

Honeywell PRO 2000 Series Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5110D Bedienungsanleitung

Honeywell

Honeywell RTH7400 series Bedienungsanleitung

Honeywell

Honeywell EnergyPro T8665C Bedienungsanleitung

Honeywell

Honeywell Y6630D1007 Betriebsanleitung

Honeywell

Honeywell S963D Bedienungsanleitung

Honeywell

Honeywell T8624D Bedienungsanleitung

Honeywell

Honeywell RRTH9590WF Bedienungsanleitung

Honeywell

Honeywell INNCOM e7w Bedienungsanleitung

Honeywell

Honeywell PRO TH3110B Bedienungsanleitung

Honeywell

Honeywell 1-Heat/1-Cool - TH5110D1022 Large R Bedienungsanleitung

Honeywell

Honeywell TH114-AF-GA Bedienungsanleitung

Honeywell

Honeywell CM737 Bedienungsanleitung

Honeywell

Honeywell TRADELINE T8400C Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Honeywell

Honeywell DT92A Kurzanleitung

Honeywell

Honeywell CT54 Bedienungsanleitung

Honeywell

Honeywell RTH1100 series Bedienungsanleitung

Honeywell

Honeywell PRO TH3110B Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung