Honeywell T822 Bedienungsanleitung

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69-1711

T822 Thermostat

STEP 1. PREPARE FOR

INSTALLATION

The T822 Thermostat controls 2-wire, 15 Vac to 30 Vac,

gas, oil or electric heating-only systems.

The T822 Thermostat is not suitable for:

• cooling systems

• heating-cooling systems

• 3-wire electric heating systems

If you are unsure which thermostat model is right for your

system, visit www.honeywell.com/yourhome or call

Honeywell Customer Care at 1-800-468-1502.

1. Check that the following components are included:

• Thermostat

• Two one-inch screws

• Installation Instructions

2. Required tools:

• Slotted screwdriver

• Drill

• Drill bit (1/16 in.)

• Needle nose pliers

• Level

• Pencil

STEP 2. REMOVE OLD

THERMOSTAT

1. Turn power off to the system at the furnace or at

the fuse/circuit breaker panel.

2. Remove cover on the old thermostat. If the cover

does not easily pull off, remove any screws that

may fasten the cover to the thermostat.

3. Locate the heat anticipator scale and the heat

anticipator lever on the old thermostat (see Fig. 1).

Fig. 1. Heat anticipator on old thermostat (example).

4. Record the number that the heat

anticipator lever points to on the heat

anticipator scale.

NOTE: If you cannot find the heat anticipator setting on

your thermostat, you can use a standard setting

for your type of system when you reach Step 5.

Set Heat Anticipator On New Thermostat.

5. Remove any screws that hold the thermostat to the

wall and pull the thermostat away from the wall.

6. Remove the two wires from the old thermostat and

wrap them around a pencil to keep them from fall-

ing back into the wall (see Fig. 2). If there are more

than two wires connected to your old thermostat,

do not remove the wires. Visit www.honey-

well.com/yourhome or call 1-800-468-1502 for fur-

ther assistance with the installation.

Fig. 2. Pull wires through wall opening.

M21192

OLD THERMOSTAT HEAT

ANTICIPATOR SCALE

HEAT ANTICIPATOR LEVER

TYPI

L LO

TIO

AND

LEVE

WIRES

THROUG

WALL

OPENING

M1964

T822 THERMOSTAT

69-1711 2

MERCURY NOTICE

If this thermostat is replacing a control that

contains mercury in a sealed tube, do not place

the old thermostat in the trash. Contact your local

waste management authority for instructions

regarding recycling and proper disposal of this

control or of an old control containing mercury in

a sealed tube.

STEP 3. CONNECT WIRES TO NEW

THERMOSTAT

IMPORTANT

All wiring must comply with local building codes

and ordinances. If you are unsure about house-

hold wiring procedures, please call your local

heating/cooling contractor.

1. Remove the cover on the new thermostat. To

remove the cover, insert your thumb into the inden-

tation on the side and pull the cover away from the

thermostat (see Fig. 3).

2. Loosen the R and W terminal screws on the back

of the new thermostat (see Fig. 4).

3. Remove the two wires from the pencil and attach

one wire to the R terminal and the other wire to the

W terminal (see Fig. 4 and 5).

4. Plug the hole in the wall with insulation to prevent a

warm or cool draft from affecting the operation of

the thermostat.

Fig. 3. Remove cover on new thermostat.

Fig. 4. R and W terminals on new thermostat.

Fig. 5. Wraparound and straight wiring connections.

STEP 4. MOUNT NEW

THERMOSTAT TO WALL

1. Position the thermostat on the wall. Place a level

on top of the thermostat and use a pencil to mark

the two mounting holes on the wall (see Fig. 6).

2. Move the thermostat to the side and drill the

mounting holes in the wall using a 1/16 in. drill bit

at the locations you marked.

3. Position the thermostat over the drilled holes and

loosely insert the mounting screws into the drilled

holes. Check the leveling of the thermostat and

tighten the mounting screws. Do not over tighten.

4. Remove styrofoam packing material that holds the

mercury switch in place during shipping.

•40•50•60•

M19979

BACK OF

THERMOSTAT

COVER

M1998

M19648

OR WRAPAROUND

NSERTION STRIP

/16 IN. (11 MM)

FOR STRAIGH

INSERTION

STRIP

5/16 IN. (8 MM

)

T822 THERMOSTAT

3 69-1711

Fig. 6. Mount new thermostat to wall.

STEP 5. SET HEAT ANTICIPATOR

ON NEW THERMOSTAT

1. Set the heat anticipator lever to the number that

you recorded in Step 2. Remove Old Thermostat,

sub-step 4 (see Fig. 7).

Fig. 7. Heat anticipator on new thermostat.

2. If you could not find a heat anticipator setting on

your old thermostat, use the setting listed in

Table 1 for your type of heating system.

Table 1. Heat Anticipator Setting.

Place the cover on the thermostat and turn the

power back on. If the heating system runs too long

to maintain a comfortable temperature, adjust heat

anticipator lever clockwise one scale mark (see Fig.

7). Do not adjust heat ancitipator below .3 Amps. If

the heating system needs to run longer to maintain

a comfortable temperature, adjust heat anticipator

lever counterclockwise, in the direction of the arrow,

one scale mark (see Fig. 7).

STEP 6. OPERATING NEW

THERMOSTAT

1. Adjust the temperature setting lever to your desired

setting. If it is too warm, lower the temperature set-

ting. If it is too cool, raise the temperature setting.

STEP 7. ADJUSTABLE RANGE

STOPS

1. The T822 Thermostat comes equipped with adjust-

able range stops (see Fig. 8). The range stops are

factory set to allow for maximum adjustment of the

temperature lever. If you choose to limit the adjust-

ment of the temperature lever, set range stops to

your desired setting.

Fig. 8. Set adjustable range stops.

.18

.25 .3

.9.7

LEVEL

DATE CODE

MODEL NO.

M19981

NOTE: MOVETEMPERATURE LEVER IF

IT BLOCKS MOUNTING HOLE

MOUNTING

HOLE

OUNTING

OLE

.18

.25 .3

.9.7

M19982

PLACE FINGER

HERE TO MOVE

LEVER

HEAT ANTICIPATOR

THIS POINT

SHOULD ALIGN WIT

HEAT ANTICIPATOR

SETTING

.18

.25 .3

.9.7

DATE CODE

MODEL NO.

Heating System

Heat Anticipator

Setting (Amps)

Hot Water .8

High Efficiency Warm Air (90% or

better)

Gas or Oil Warm Air .4

Electric .3

M22003

.18

.25 .3

DATE CODE

MODEL NO.

ADJUSTABLE

RANGE

STOPS

69-1711 J.S. 2-04 www.honeywell.com/yourhome

T822 THERMOSTAT

Printed in U.S.A. on recycled

paper containing at least 10%

post-consumer paper fibers.

Automation and Control Solutions

Honeywell International Inc. Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Scarborough, Ontario

M1V 4Z9

IF YOU HAVE A PROBLEM Customer Assistance

Please read and follow the provided instructions for this

thermostat. For additional information, go to

www.honeywell.com/your home or call Honeywell

Customer Care at 1-800-468-1502.

Before calling, please have the following information

available:

• Thermostat model number and date code (refer to

Fig. 6 for the location of the model number and date

code).

• Type of heating system (for example: gas or oil; warm

air, hot water).

If. . . Then. . .

Heating system

does not come on.

•Make sure the temperature

setting is above the room

temperature.

•Make sure the circuit breaker

is not tripped and reset it if

necessary.

•Make sure the power switch at

the equipment is in the On

position.

•Wait 5 minutes for the system

to respond.

Heating system runs

too long to maintain

a comfortable

temperature.

•Verify the thermostat is level.

•Adjust heat anticipator lever

clockwise one scale mark (see

Fig. 7). Do not adjust heat

anticipator below .3 Amps.

Heating system

needs to run longer

to maintain a

comfortable

temperature.

•Verify the thermostat is level.

•Adjust heat anticipator lever

counterclockwise, in the

direction of the arrow, one

scale mark (see Fig. 7).

Temperature lever

cannot be set to the

highest and/or

lowest setting on the

temperature scale.

•Adjust temperature range

stops (see Fig. 8).

Andere Handbücher für T822

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Bedienungsanleitung

Honeywell

Honeywell HEAT PUMP THERMOSTAT T8411R Bedienungsanleitung

Honeywell

Honeywell AQ1000TN2 - Low Voltage T-Stat Bedienungsanleitung

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Bedienungsanleitung

Honeywell

Honeywell DTS92 Bedienungsanleitung

Honeywell

Honeywell T8635L Bedienungsanleitung

Honeywell

Honeywell th511od Bedienungsanleitung

Honeywell

Honeywell Y87RF Bedienungsanleitung

Honeywell

Honeywell CT30 Series Bedienungsanleitung

Honeywell

Honeywell Lyric Enrollment Bedienungsanleitung

Honeywell

Honeywell TP979A-E Bedienungsanleitung

Honeywell

Honeywell Round CT87B Montageanleitung

Honeywell

Honeywell T6861-F Bedienungsanleitung

Honeywell

Honeywell T11A Montageanleitung

Honeywell

Honeywell VisionPRO TH8110U Bedienungsanleitung

Honeywell

Honeywell CT8611 Bedienungsanleitung

Honeywell

Honeywell CHRONOTHERM III T8611G Bedienungsanleitung

Honeywell

Honeywell RF CM61NG Bedienungsanleitung

Honeywell

Honeywell T6360 Bedienungsanleitung

Honeywell

Honeywell DT92E Bedienungsanleitung

Honeywell

Honeywell CM900 Bedienungsanleitung

Honeywell

Honeywell Evohome Bedienungsanleitung

Honeywell

Honeywell MagicStat T8132 Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung