Honeywell T80 Bedienungsanleitung

Quick Guide

OVERVIEW

Scan Light

Receiver

Power Light

Scan

Enter

F2 Key

Delete

Speaker

Scan window

Flash lamp

Camera

Card

Reading area

Power Button

Scan

Return

F1 Key

Microphone

Type-C

interface

Power Button

Battery cover

HOME

Hot button/Custom button

1. Screen capture: "power"+"Volume -"

2. Custom button: Setting → Feature → Custom Key

3. Letter input switching: Press"1-A" on Keyboard

STRAP INSTALLATION

Buckle

(As Pic1)

Following the direction of the above arrow, push the strap

buckle up to secure it.

OPEN THE BATTERY COVER

Please remove the positive and negative insulation yellow

sticker on the battery before turning on tne device.

1. Push the battery cover button in anti-clockwise direction.

(As Pic1)

2. Pull out the battery cover by using the hand position between the

battery cover and the bottom case.

REMOVING-THE BATTERY

1. Lift the strap on the battery:

2. Pull the battery belt to take the battery off on 45° obliquely

upward.

INSTALL TF/SIM CARD

TF slot

PSAM slotx 2

Micro SIM slot

1. Insert the SIM card into the corresponding slots as shown in

the figure below

(Note: The handheld terminal only supports Micro SIM card; the

standard SIM card slot is for PSAM card)

EQUIPMENT CHARGING

Type-C interface

1. Pull out the waterproof USB plug on the right side with the Type-C

USB cable that comes with the device.Insert the Type-C USB cable.

2. Use cradle to charge. (Cradle comes seperately)

DEVICE CHARGING:

1. Battery is fully charged after 4 hours of charging, and the standby

time is over 48 hours.

2. Cradle can charge 1 battery and 1 terminal simultaneously.

3. The left indicator light is the battery charging indicator, when the

battery is charging, it will appear red. Light will display green once

fully charged.

4. The right light is the power on indicator. Green for when power is

on, and indicator is off when power is off.

*To prevent the battery from being over-consumed, please charge

the device when the battery power is less than 20%. If the battery

displays over-comsumption state, please charge the device for

20-30 minutes. This then will display a normal charging status.

SCAN(OPTIONAL)

Clear the

contents

Settings

About

Scan key

Scan window

Reset scan

Function setting:

Enter/Tab

Append prefix/

suffix

(Pic1)

1. Find the "scanner" app, and open it.(As Pic 1)

2. In the scan interface, press scan button to scan the barcode.

IF PDA COMES WITH SCAN FUNCTION, OPERATE AS BELOW:

NFC(OPTIONAL)

NFC reading

(Pic1)

(Pic 2)

1. Find the “NFC" app, and open it.(As Pic 1)

2. In the NFC interface, please read the card by NFC reading area.

IF PDA WITH NFC FUNCTION, OPERATE AS BELOW:

(Note: NFC function is optional feature, you should make sure PDA

includes NFC function)

OTA(UPDATE ONLINE)

(As Pic1) (As Pic 2)

1. Select "Settings"- About phone.

2. Press "System update" and enter into the updating firmware interface.

3. Press "Check now" to update the OS.

OUR PDA SUPPORT OTA(UPDATE ONLINE)FUNCTION,YOU CAN

UPDATE THE LATEST FIRMWARE BY OTA, OPERATE IT AS BELOW:

Inhaltsverzeichnis

Andere Honeywell Touch-Terminal Handbücher

Honeywell

Honeywell VM3AL0N Bedienungsanleitung

Honeywell

Honeywell TemaKey Bedienungsanleitung

Honeywell

Honeywell CT40 HomeBase Bedienungsanleitung

Honeywell

Honeywell Marathon Bedienungsanleitung

Honeywell

Honeywell VISTA Series Bedienungsanleitung

Honeywell

Honeywell ADEMCO 6271 Series Montageanleitung

Honeywell

Honeywell TemaLine TemaKey Bedienungsanleitung

Honeywell

Honeywell temaserver TS TA series Bedienungsanleitung

Honeywell

Honeywell JetWave MCS-8562 Handbuch

Honeywell

Honeywell SP5600-C OptimusR Bedienungsanleitung

Honeywell

Honeywell Notifier TAD-FTT Bedienungsanleitung

Honeywell

Honeywell NOTIFIER N-ANN-80 Series Technisches Handbuch

Honeywell

Honeywell Dolphin 75e Bedienungsanleitung

Honeywell

Honeywell TemaKey TK C03 Bedienungsanleitung

Honeywell

Honeywell Dolphin 70e Black Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung