Honeywell WAP Bedienungsanleitung

WAP Wireless Access Point – Quick Installation Guide

For Online Support visit: http://www.security.honeywell.com/hsc/resources/MyWebTech/

General Information

This guide provides information on installing and setting up Honeywell's WAP Wireless Access

Point. The WAP provides an easy-to-setup secure wireless solution that enables Honeywell's

iPCAM series internet video cameras to communicate with a broadband modem or LAN.

Some major features of Honeywell's WAP Wireless Access Point are:

•Functions as a secure wireless access point.

•Wireless communications utilizes the 802.11b/g/n protocol with WPS security. WPS (Wi-Fi

Protected Setup) is a standard for easy setup of a secure wireless network.

•In addition to wireless communications, there are three 10/100 Mbps Ethernet ports

available for wired cameras.

IMPORTANT: This device is for indoor use only.

PACKAGE CONTENTS

LAN

Wireless

WPS

Reset

Security

Power

WAP Wireless Access Point

Antenna [Qty 2]

Power Transformer

Ethernet Cable

Component Identification

Security WPS Wireless LAN Power Reset

Security:

On – WPS security is set to on.

Flashing – Flashes when WPS button has

been pressed for 3 seconds and released,

to indicate the WAP is transmitting a new

security key to the wireless camera. When

the wireless camera replies, the Security

LED lights solid.

WPS (button): Used to setup a secured

wireless connection. (Refer to the

documentation for the wireless camera.)

Wireless:

On – Wireless connection exist.

Off – No Wireless connections exist.

Flashing (Amber) – Problem occurred while

trying to establish the Wireless connection.

LAN:

On – The LAN port(s) is active.

Flashing (Amber) – Problem occurred while

trying to connect to the LAN.

Power: When power is applied the LED

blinks during an initialization period, then

remains steady to indicate power is

connected.

Reset (switch): This switch has two

functions; Reboot, and Clear All Data. Use

a paper clip to depress.

Reboot – Depress and Release to reboot.

(Allow cycle to complete.)

Clear All Data – Depress and hold for 8

seconds to clear all data, and restore

factory settings. (Allow cycle to complete.)

12V / 1A: Connect Power Transformer.

WAN: Not Used. (Do not remove the cap plug.)

Ports 1, 2, 3, 4: For connection to Ethernet devices.

Antenna Ports: Connect the supplied antennas to these ports.

Antenna

Port (2)

Typical Setup Configuration for the WAP

For specific setup and configuration instructions for your

wireless camera, refer to the camera's installation guide.

1. If using wireless connectivity, attach the two antennas to the WAP. Orient

each antenna vertically and tighten the knurled connectors.

2. Connect the Power Transformer wire to the 12V / 1A connector on the

WAP back. Plug the Power Transformer into an outlet.

NOTE: The Power Transformer must be powered by a non-switchable

power outlet.

IMPORTANT:

•When setting up a wireless configuration in very large buildings or

buildings with dense walls, wireless communications may be marginal. It is

best to first configure the system in the same room. Then upon successful

configuration, place each wireless camera in the desired location.

•If using more than one wireless camera, each must be configured for

wireless security.

•If using a router instead of Honeywell's WAP, please ensure your router is

configured for DHCP. (This is the default setting for most routers.) If you

are unsure, you can access the router's configuration page and set it for

DHCP if necessary (refer to the router's manual). Since the operation of

each router varies, please refer to the router's manufacturer for support.

•Test the system to ensure all cameras exhibit good communications.

Typical configuration using a mix of wired and wireless cameras:

Ê800-05000:Š

800-05000 11/09 Rev. A

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

WARRANTY

For the latest warranty information go to:

http://www.security.honeywell.com/hsc/resources/wa/

Andere Honeywell Drahtloser Zugangspunkt Handbücher

Honeywell

Honeywell WAP-PLUS Bedienungsanleitung

Honeywell

Honeywell AVS Bedienungsanleitung

Honeywell

Honeywell FocusBT AP-010-BT Bedienungsanleitung

Honeywell

Honeywell 51306533 Bedienungsanleitung

Honeywell

Honeywell FocusBT AP-010-BT Bedienungsanleitung

Honeywell

Honeywell FocusBT AP-010-BT Bedienungsanleitung

Honeywell

Honeywell LYNX Series Bedienungsanleitung

Honeywell

Honeywell OW-FDAP31 Bedienungsanleitung

Honeywell

Honeywell Field Device Access Point Bedienungsanleitung

Honeywell

Honeywell WAP-PLUS Bedienungsanleitung

Honeywell

Honeywell FocusBT AP-100-BT Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung