HORNER XLE Bedienungsanleitung

Page 1

XLE/XLEe & XLT/XLTe - Model 0

No Built-In I/O

MAN1112-20-EN_XLET_Mod0



FindthemanualsviatheDocumentationSearchpageon

theHornerwebsite.



Part Numbers

Global Part Numbers

XLE-Model0 HE-XE100

XLEe-Model0withEthernet HE-XE1E0

XLT-Model0 HE-XT100

XLTe-Model0withEthernet HE-XT1E0

European Part Numbers

XLE-Model0 HEXE220C100

XLEe-Model0withEthernet HEXE221C100

XLT-Model0 HEXT240C100

XLTe-Model0withEthernet HEXT241C100



Accessories and Add-Ons

Part# Description

HE-BAT009 CR2450LithiumCoinBattery

HE-XCK ProgrammingCables

HE-XDAC 2channelAnalogOutputI/Ooptionkit,

selectable0-10V,+/-10V,4-20mA.

HE-XDAC107 4channelAnalogOutputI/Ooptionkit,

selectable0-10V,+/-10V,4-20mA.

HE-XKIT BlankI/OBoard

HE200MJ2TRM Adapter,RJ45(8P8C)maleto8-pos-

itionterminalstrip.

HE-FBD001 Ferritecoreforfilteringoutelectrical

noise.



XLE/XLT User Manual - MAN0878

FindthemanualsviatheDocumentationSearchpageon

theHornerwebsite.



Table of Contents

TECHNICAL SPECIFICATIONS 2

GeneralSpecifications 2

ControlandLogic 2

UserInterface 2

Connectivity 2

CONTROLLER OVERVIEW 3

OverviewofXLEandXLT 3

PowerWiring 3

COMMUNICATIONS 4

SerialCommunication 4

MJ1Wiring 4

MJ2Wiring 4

Ethernet 4

CANCommunications 4

DipSwitches 4

DIMENSIONS & INSTALLATION 5

Dimensions&PanelCutout 5

InstallationInformation 5

InstallationProcedure 5

BatteryMaintenance 5

SAFETY & MAINTENANCE 6

Warnings 6

FCCCompliance 6

TechnicalSupport 6

Precautions 6



Page 2

TECHNICAL SPECIFICATIONS

General Specifications

PrimaryPowerRange 10-30VDC

RequiredPower

(SteadyState) 130mA@24VDC

InrushCurrent 30Afor<1ms

Typicalpowerback-

light100%

136mA@10V(1.36W)

64mA@24V(1.53W)

PowerBacklightOff 15mA@24V(0.36W)

PowerEthernet

Models

35mA@10V(0.35W)

20mA@24V(0.48W)

HeaterOption* 250mA@24VDCwithheater*

RealTimeClock Batterybacked;lithiumcoincell

CR2450

ClockAccuracy +/-90Secs/Month

RelativeHumidity 5to95%Non-condensing

OperatingTemp. -10°Cto+60°C

StorageTemp. -20°Cto+70°C

Weight 0.75lbs/340g(withoutI/O)

Altitude Upto2000m

RatedPollution

Degree

EvaluatedforPollutionDegree2

Rating

Certifications(UL/CE) NorthAmericaorEurope

*HeaterOption(Model#plus"-22")



Control and Logic

ControlLang.Support

LadderLogic;

Variable-BasedAdvanced

Ladder

IEC61131-3Languages

LogicProgramSize 256kB

ScanRate 0.7ms/kBlogic(XLE)

0.8ms/kBlogic(XLT)

DigitalInputs 2048

DigitalOutputs 2048

AnalogInputs 512

AnalogOutputs 512

Gen.PurposeRegisters

9,999(words)Retentive

2,048(bits)Retentive

2,048(bits)Non-retentive



User Interface

DisplayType TransflectiveLCDSun-lightRead-

able

Resolution 128x64pixels(XLEe)

160x128pixels(XLTe)

Color Monochrome

Built-InStorage 16MB

User-Program.

Screens

1023maxpages;

50objectsperpage

Backlight LED

BacklightLifetime 30,000+hrs

BrightnessControl

0-100%(XLT)

On/Off(XLE)via

SystemRegister%SR57

NumberofKeys 20(XLE)

5(XLT)

Touchscreen(XLTe) Resistive1,000,000+touchlife



Connectivity

SerialPorts

RS-232fullhandshakingorRS-485half

duplexonfirstModularJack(MJ1)

RS-232orRS-485onsecondModularJack

(MJ2)

USBMini-B Programmingonly

CAN 1xCANPort,Isolated1kV

CAN

Protocols CsCAN,CANopen,DeviceNet,J1939

Ethernet Ethernetversionsonly[XLEe&XLTe]

Ethernet

Protocols

TCP/IP,ModbusTCP,FTP,SRTP,EGD,

ICMP,ASCII

RemoteI/O SmartRail,SmartStix,SmartBlock,

SmartMod

Removable

Memory

MicroSD,SDHC,SDXC,INFAT32format,

supportfor32GBmax.Application

Updates,Datalogging...

Audio

(XLTeonly) Beeper,SystemorSoftwareControlled

Page 3

CONTROLLER OVERVIEW

Overview of XLE and XLT

1. FunctionKeys

2. Touchscreen

3. NavigationKeys

4. USBMini-BPort

5. HighCapacitymicroSDSlot

6. RS232/RS485SerialPorts(2)

7. Wide-RangeDCPower

8. CANPort

9. EthernetLANPort(XLEeandXLTeonly)

10. OptionalBuilt-InI/O(Models2-6only)

11. ConfigurationSwitches

12. MountingClipLocations

13. DINRailClip

14. Softkeys

NOTE:SeePrecaution#12onaboutUSBandgrounding.



Power Wiring

NOTE:ThePrimaryPowerRangeis10VDCto30VDC.



Primary Power Port Pins

PIN Signal Description

1 Ground FrameGround

2 DC- InputPowerSupplyGround

3 DC+ InputPowerSupplyVoltage



DC Input / Frame

lSolid/StrandedWire:12-24awg(2.5-0.2mm)

lStriplength:0.28”(7mm)

lTorque,TerminalHold-DownScrews:4.5–7in-lbs

(0.50–0.78N-m)

lDC-isinternallyconnectedtoI/OV-,butisisolated

fromCANV-.AClass2powersupplymustbeused.



Power Up



1. OPTION:Attachferritecorewithaminimumoftwo

turnsoftheDC+andDC-signalsfromtheDCsupply

thatispoweringthecontrollers.



2. Connecttoearthground.

3. Applyrecommendedpower.

Page 4

COMMUNICATIONS

Serial Communication

MJ1 Wiring

RS-232withfullhandshakingorRS-485half-

duplex

RS-485terminationviaswitches;biasingviasoft-

ware

MJ1 Pins

PIN SIGNAL DIRECTION

8 TXD OUT

7 RXD IN

6 0V GROUND

5 +5V@60mA OUT

4 RTS OUT

3 CTS IN

2 RX-/TX- IN/OUT

1 RX+/TX+ IN/OUT



MJ2 Wiring

RS-232orRS-485halforfull-duplex,software

selectable

RS-485terminationviaswitches;biasingvia

software

MJ2 Pins

PIN SIGNAL DIRECTION

8 232TXD OUT

7 232RXD IN

6 0V GROUND

5 +5V@60mA OUT

4 485TX- OUT

3 485TX+ IN

2 485RX-orRX/TX- INorIN/OUT

1 485RX+orRX/TX+ INorIN/OUT



NOTE:Attachoptionalferritecorewithaminimumoftwo

turnsofserialcable.



Ethernet

Green LED indicates link-whenillu-

minated,datacommunicationisavailable.

Yellow LED indicates activity-when

flashing,dataisintransmission.

CAN Communications



CAN Pin Assignments

PIN SIGNAL DESCRIPTION

1 V- CANGround–Black

2 CN_L CANDataLow–Blue

3 SHLD ShieldGround–None

4 CN_H CANDataHigh–White

5 V+(NC) NoConnect–Red



lSolid/Stranded Wire:12-24awg(2.5-0.2mm).

lStrip Length:0.28”(7mm).

lLockingspring-clamp,two-terminatorspercon-

ductor.

lTorque, Terminal Hold-Down Screws:4.5–7in-

lbs(0.50–0.78N-m).

lV+pinisnotinternallyconnected,theSHLDpinis

connectedtoEarthgroundviaa1MΩresistorand10

nFcapacitor.



Dip Switches



DIP Switches

PIN NAME FUNCTION DEFAULT

1MJ1RS-485

Termination

ON=Ter-

minated OFF

2MJ2RS-485

Termination

ON=Ter-

minated OFF

3 Bootload AlwaysOff OFF



TheDIPswitchesareusedtoprovideabuilt-intermination

toboththeMJ1portandMJ2portifneeded.Theter-

minationfortheseportsshouldonlybeusedifthisdeviceis

locatedateitherendofthemultidrop/daisy-chainedRS-

485network.

Page 5

DIMENSIONS & INSTALLATION

Dimensions & Panel Cutout



Installation Information



lTheXLE/XLTutilizesaclipinstallationmethodto

ensurearobustandwatertightsealtotheenclosure.

Pleasefollowthestepsbelowfortheproperinstall-

ationandoperationoftheunit.

lThisequipmentissuitableforClassI,Division2,

GroupsA,B,CandDornon-hazardouslocations

only.

lDigitaloutputsshallbesuppliedfromthesame

sourceastheoperatorcontrolstation.

lJumpersonconnectorJP1shallnotberemovedor

replacedwhilethecircuitisliveunlesstheareais

knowntobefreeofignitableconcentrationsofflam-

mablegasesorvapors.



Installation Procedure

1. Carefullylocateanappropriateplacetomountthe

XLE/XLT.Besuretoleaveenoughroomatthetopof

theunitforinsertionandremovalofthemicroSD™

card.

2. Carefullycutthehostpanelperthediagram,cre-

atinga92mmx92mm+/-0.1mmopeningintowhich

theXLE/XLTmaybeinstalled.Iftheopeningistoo

large,watermayleakintotheenclosure,potentially

damagingtheunit.Iftheopeningistoosmall,the

OCSmaynotfitthroughtheholewithoutdamage.

3. Removeanyburrsandorsharpedgesandensure

thepanelisnotwarpedinthecuttingprocess.

4. RemoveallRemovableTerminalsfromthe

XLE/XLT.InserttheXLE/XLTthroughthepanel

cutout(fromthefront).Thegasketmustbebetween

thehostpanelandtheXLE/XLT.

5. Installandtightenthefourmountingclips(provided

inthebox)untilthegasketformsatightseal(NOTE:

Maxtorque0.8to3Nm,or7-10in-lbs).

6. ReinstalltheXLE/XLTI/ORemovableTerminal

Blocks.Connectcommunicationscablestothe

serialport,USBports,Ethernetport,andCANport

asrequired.



Battery Maintenance



TheXLE/XLTusesareplaceablenon-rechargeable3VLith-

iumcoincellbattery(CR2450)toruntheReal-TimeClock

andtokeeptheretainedregistervalues.Thisbatteryis

designedtomaintaintheclockandmemoryfor7to10

years.PleasereferenceMAN0878providinginstructions

onhowtoreplacethebattery.

Page 6

SAFETY & MAINTENANCE

Warnings

1. Toavoidtheriskofelectricshockorburns,alwayscon-

nectthesafety(orearth)groundbeforemakinganyother

connections.

2. Toreducetheriskoffire,electricalshock,orphysical

injury,itisstronglyrecommendedtofusethevoltage

measurementinputs.Besuretolocatefusesascloseto

thesourceaspossible.

3. Replacefusewiththesametypeandratingtoprovidepro-

tectionagainstriskoffireandshockhazards.

4. Intheeventofrepeatedfailure,doNOTreplacethefuse

againasrepeatedfailureindicatesadefectivecondition

thatwillNOTclearbyreplacingthefuse.

5. Onlyqualifiedelectricalpersonnelfamiliarwiththecon-

structionandoperationofthisequipmentandthehazards

involvedshouldinstall,adjust,operate,orservicethis

equipment.

6. Readandunderstandthismanualandotherapplicable

manualsintheirentiretybeforeproceeding.Failureto

observethisprecautioncouldresultinseverebodilyinjury

orlossoflife.

7. WARNING-Batterymayexplodeifmistreated.Donot

recharge,disassemble,ordisposeofinfire.

8. WARNING - EXPLOSION HAZARD-Batteriesmustonly

bechangedinanareaknowntobenon-hazardous.



FCC Compliance

ThisdevicecomplieswithPart15oftheFCCRules.Operationis

subjecttothefollowing

twoconditions:

1. Thisdevicemaynotcauseharmfulinterference.

2. Thisdevicemustacceptanyinterferencereceived,includ-

inginterferencethatmaycauseundesiredoperation.



Technical Support

North America

1(317)916-4274

(877)665-5666

www.hornerautomation.com

[email protected]



Europe

+353(21)4321-266

www.hornerautomation.eu

[email protected]



Precautions

Allapplicablecodesandstandardsneedtobefollowedinthe

installationofthisproduct.Adheretothefollowingsafetypre-

cautionswheneveranytypeofconnectionismadetothemodule:

1. Connectthesafety(earth)groundonthepowerconnector

firstbeforemakingany

2. otherconnections.

3. Whenconnectingtotheelectriccircuitsorpulse-initiating

equipment,opentheir

4. relatedbreakers.

5. DoNOTmakeconnectiontolivepowerlines.

6. Makeconnectionstothemodulefirst;thenconnecttothe

circuittobemonitored.

7. Routepowerwiresinasafemannerinaccordancewith

goodpracticeandlocalcodes.

8. Wearproperpersonalprotectiveequipmentincluding

safetyglassesandinsulatedgloveswhenmakingcon-

nectionstopowercircuits.

9. Ensurehands,shoes,andflooraredrybeforemakingany

connectiontoapowerline.

10. MakesuretheunitisturnedOFFbeforemakingcon-

nectiontoterminals.

11. Makesureallcircuitsarede-energizedbeforemakingcon-

nections.

12. Beforeeachuse,inspectallcablesforbreaksorcracksin

theinsulation.Replace

13. immediatelyifdefective.

14. UsecopperconductorsinFieldWiringonly,60/75˚C.

15. UsecautionwhenconnectingcontrollerstoPCsviaserial

orUSB.PCs,especiallylaptops,mayuse“floatingpower

supplies”thatareungrounded.Thiscouldcauseadam-

agingvoltagepotentialbetweenthelaptopandcontroller.

Ensurethecontrollerandlaptoparegroundedformax-

imumprotection.ConsiderusingaUSBisolatordueto

voltagepotentialdifferencesasapreventativemeasure.



Andere Handbücher für XLE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HORNER Steuerungssystem Handbücher

HORNER

HORNER HE500OCS050 Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung