Hoshizaki KML-700MWH-M Bedienungsanleitung

Hoshizaki

“A Superior Degree

of Reliability”

www.hoshizaki.com

Model

KML-700MWH-M

Low-Profile Modular Crescent Cuber

Hoshizaki America, Inc.

Issued: 10-13-2009

INSTRUCTION MANUAL

™

IMPORTANT

Only qualied service technicians should install, service, and maintain the

icemaker. No installation, service, or maintenance should be undertaken

until the technician has thoroughly read this Instruction Manual. Likewise, the

owner/manager should not proceed to operate the icemaker until the installer

has instructed them on its proper operation. Failure to install, operate, and

maintain the equipment in accordance with this manual may adversely affect

safety, performance, component life, and warranty coverage.

Hoshizaki provides this manual primarily to assist qualied service technicians in the

installation, maintenance, and service of the icemaker.

Should the reader have any questions or concerns which have not been satisfactorily

addressed, please call, write, or send an e-mail message to the Hoshizaki Technical

Support Department for assistance.

HOSHIZAKI AMERICA, INC.

618 Highway 74 South

Peachtree City, GA 30269

Attn: Hoshizaki Technical Support Department

Phone: 1-800-233-1940 Technical Support

(770) 487-2331

Fax: 1-800-843-1056

(770) 487-3360

E-mail: [email protected]

Web Site: www.hoshizaki.com

NOTE: To expedite assistance, all correspondence/communication MUST include the

following information:

  •ModelNumber

  •SerialNumber

  •Completeanddetailedexplanationoftheproblem.

CONTENTS

Important Safety Information ................................................................................................. 4

I. Specications...................................................................................................................... 5

A. Nameplate Rating ......................................................................................................... 5

B. Dimensions/Connections .............................................................................................. 6

II. Installation and Operating Instructions .............................................................................. 7

A. Checks Before Installation............................................................................................. 7

B. How to Remove Panels ................................................................................................. 7

C. Location ........................................................................................................................ 8

D. Setup............................................................................................................................. 8

E. Electrical Connection .................................................................................................... 9

F. Water Supply and Drain Connections .......................................................................... 10

1. Icemaker ................................................................................................................ 10

2. Water-Cooled Condenser........................................................................................11

a) Connection to an Open Drain System .................................................................11

b) Connection to a Closed Loop System ................................................................ 12

G. Final Checklist ............................................................................................................ 13

H. Startup ........................................................................................................................ 14

III. Cleaning and Maintenance ............................................................................................. 15

A. Cleaning and Sanitizing Instructions .......................................................................... 15

1. Cleaning Procedure................................................................................................ 15

2. Sanitizing Procedure - Following Cleaning Procedure ........................................... 17

B. Maintenance................................................................................................................ 17

C. Preparing the Icemaker for Long Storage ................................................................... 18

IMPORTANT

This manual should be read carefully before the icemaker is installed and

operated. Only qualied service technicians should install, service, and

maintain the icemaker. Read the warnings contained in this booklet carefully as

they give important information regarding safety. Please retain this booklet for

any further reference that may be necessary.

Important Safety Information

Throughout this manual, notices appear to bring your attention to situations which could

result in death, serious injury, or damage to the unit.

WARNING Indicates a hazardous situation which could result in death or

serious injury.

CAUTION Indicates a situation which could result in damage to the unit.

IMPORTANT Indicates important information about the use and care of the

unit.

WARNING

This icemaker should be destined only to the use for which it has been

expressly conceived. Any other use should be considered improper and

therefore dangerous. The manufacturer cannot be held responsible for

eventual damage caused by improper, incorrect, and unreasonable use.

To reduce the risk of death, electric shock, serious injury, or re, follow

basic precautions including the following:

•Electricalconnectionmustbehard-wiredandmustmeetinternational,

national, state, and local electrical code requirements. Failure to meet these

code requirements could result in death, electric shock, serious injury, re, or

severe damage to equipment.

•Thisunitrequiresanindependentpowersupply.Seethenameplatefor

proper voltage and breaker/fuse size. Failure to use a proper breaker or fuse

can result in a tripped breaker, blown fuse, or damage to existing wiring. This

could lead to heat generation or re.

•THIS UNIT MUST BE GROUNDED. Failure to properly ground this unit could

result in death or serious injury.

•Thisunitshouldbedisassembledorrepairedonlybyqualiedservice

personnel to reduce the risk of electric shock, injury, or re.

•Donotmakeanyalterationstotheunit.Alterationscouldresultinelectric

shock, injury, re, or damage to the unit.

MOTOR-COMPRESSOR THERMALLY PROTECTED,

NOT INTENDED FOR OUTDOOR USE!

Hoshizaki America, Inc.

Peachtree City, GA

www.hoshizaki.com

ICE MAKER

WITHOUT

STORAGE

MEANS

45FE

COMPONENT

I. Specications

A. Nameplate Rating

1. KML-700MWH-M (water-cooled marine)

See the nameplate for electrical and refrigeration specications. This nameplate is located

on the rear panel.

Since this nameplate is located on the rear panel of the icemaker, it cannot be read when

the back of the icemaker is against a wall or against another piece of kitchen equipment.

Therefore, the necessary electrical and refrigeration information is also on the rating label,

which can be easily seen by removing only the front panel of the icemaker.

We reserve the right to make changes in specications and design without prior notice.

HOSHIZAKI ICE MAKER

MODEL NUMBER KML-700MWH-M

SERIAL NUMBER

AC SUPPLY VOLTAGE 208-230/60/1 (2 WIRE)

COMPRESSOR 208-230V 6.1RLA 54LRA

PUMP 120V 0.5FLA

FAN --- --- ---

OTHER 115-120V 0.3A

MAXIMUM FUSE SIZE 15 AMPS

MAX. HACR BREAKER(USA ONLY) 15 AMPS

MAX. CIRC. BREAKER (CANADA ONLY) 15 AMPS

MINIMUM CIRCUIT AMPACITY 15 AMPS

DESIGN PRESSURE HI-427PSI LO-230PSI

REFRIGERANT 404A 1 LB. 6.9 OZ.

B. Dimensions/Connections

1. KML-700MWH-M (water-cooled marine)

Unit: in. (mm)

II. Installation and Operating Instructions

WARNING

1. This icemaker must be installed in accordance with applicable international,

national, state, and local regulations.

2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews

are securely in place after installation. Make sure that none have fallen into

the dispenser unit/storage bin.

A. Checks Before Installation

•Visuallyinspecttheexterioroftheshippingcontainerandimmediatelyreportany

damage to the carrier. Upon opening the container, any concealed damage should also

be immediately reported to the carrier.

•Removetheshippingcarton,tape,andpackingmaterial.Ifanyareleftintheicemaker,

it will not work properly.

•Removethepanelstopreventdamagewheninstallingtheicemaker.See"II.B.Howto

RemovePanels."

•Removethepackagecontainingtheaccessories.

•Removetheprotectiveplasticlmfromthepanels.Iftheicemakerisexposedtothe

sun or to heat, remove the lm after the icemaker cools.

•Checkthattherefrigerantlinesdonotrubortouchlinesorothersurfaces.

•Checkthatthecompressorissnugonallmountingpads.

•Seethenameplateontherearpanel,andcheckthatyourvoltagesupplied

corresponds with the voltage specied on the nameplate.

•Thisicemakercanbeinstalledonadispenserunitorstoragebin30"wideorwider.For

options, contact your local Hoshizaki distributor.

B. How to Remove Panels

See Fig. 1

•FrontPanel:Removethescrew.Liftup

and towards you.

•TopPanel:Liftupatfrontslightly,push

rearward, and lift off.

•SidePanel(R):Removethescrew.Slide

forward slightly and lift off.

•FrontInsulationPanel:Liftupslightly,and

pull towards you.

•TopInsulationPanel:Liftoff.

Fig. 1

Top Panel

Front Insulation Panel

Front

Panel

Screw Screw

Side

Panel

(R)

Top Insulation Panel

C. Location

CAUTION

1. This icemaker is not intended for outdoor use. Normal operating ambient

temperature should be within 45°F to 100°F (7°C to 38°C); Normal operating

water temperature should be within 45°F to 90°F (7°C to 32°C). Operation

of the icemaker, for extended periods, outside of these normal temperature

ranges may affect icemaker performance.

2. This icemaker will not work at sub-freezing temperatures. To prevent

damage to the water supply line, drain the icemaker if the air temperature is

goingtogobelow32°F(0°C).See"III.C.PreparingtheIcemakerforLong

Storage."

For best operating results:

•Theicemakershouldnotbelocatednexttoovens,grills,orotherhighheatproducing

equipment.

•Thelocationshouldprovidearmandlevelfoundationfortheequipment.

•Allow6"(15cm)clearanceatrear,sides,andtopforproperaircirculationandeaseof

maintenance and/or service should they be required.

D. Setup

1) Follow the dispenser unit/storage bin setup procedure.

2) Position the dispenser unit/storage bin in the selected permanent location.

3) Place the icemaker on top of the dispenser unit/storage bin.

4) Secure the icemaker to the dispenser unit/storage bin using the 2 mounting brackets

and the bolts provided. See Fig. 2.

5) Level the icemaker and dispenser unit/storage bin in

both the left-to-right and front-to-rear directions. If using

a storage bin, adjust the storage bin legs to make the

icemaker level.

6) Make sure the icemaker and dispenser unit/storage bin

are properly secured.

7) Seal as required by sanitation code.

8) Replace the panels in their correct positions.

Fig. 2

Icemaker

Bolts

Mounting

Brackets

Bin

E. Electrical Connection

WARNING

1. Electrical connection must be hard-wired and must meet international,

national, state, and local electrical code requirements. Failure to meet these

code requirements could result in death, electric shock, serious injury, re, or

severe damage to equipment.

2. This unit requires an independent power supply. See the nameplate for

proper voltage and breaker/fuse size. Failure to use a proper breaker or fuse

can result in a tripped breaker, blown fuse, or damage to existing wiring. This

could lead to heat generation or re.

3. THIS UNIT MUST BE GROUNDED. Failure to properly ground this unit

could result in death or serious injury.

4. Electrical connection must be made in accordance with the instructions on

the"WARNING"tag,providedwiththepigtailleadsinthejunctionbox.See

Fig. 3.

•Usuallyanelectricalpermitandservicesofalicensedelectricianarerequired.

•Themaximumallowablevoltagevariationis±10percentofthenameplaterating.

•Thetransformer'svoltagetapswitchmustbepositionedtomatchincomingvoltageat

startup.

•Theopeningforthepowersupplyconnectionis7/8"DIAtota1/2"tradesizeconduit.

Fig. 3

KML-700MWH-M

WARNING

ELECTRICAL CONNECTION

THIS UNIT MUST BE GROUNDED

Failure to properly ground or wire

this unit could result in death,

serious injury, or severe damage to

the icemaker.

The transformer’s voltage tap switch

must be positioned to match incoming

voltage at startup.

See diagram below.

4A4741-010

208-230/60/1

BROWN

JUNCTION BOX

208-230

BLACK

F. Water Supply and Drain Connections

See Fig. 4 or 5

WARNING

1. Water supply and drain connections must be installed in accordance with

applicable international, national, state, and local regulations.

2. Normal operating water temperature should be within 45°F to 90°F (7°C

to 32°C). Operation of the icemaker, for extended periods, outside of this

normal temperature range may affect icemaker performance.

3. To prevent damage to equipment, do not operate the icemaker when the

water supply is off, or if the pressure is below 10 PSIG. Do not run the

icemaker until the proper water pressure is reached.

•Aplumbingpermitandservicesofalicensedplumbermayberequiredinsomeareas.

•Externallters,strainers,orsoftenersmayberequireddependingonwaterquality.

Contact your local Hoshizaki distributor for recommendations.

•Watersupplypressureshouldbeaminimumof10PSIGandamaximumof113PSIG.If

the pressure exceeds 113 PSIG, the use of a pressure reducing valve is required.

•Theicemakerdrainline,dispenserunit/storagebindrainline,andwater-cooledcondenser

drain line must be run separately.

•Drainlinesmusthave1/4"fallperfoot(2cmper1m)onhorizontalrunstogetagood

ow. A vented tee connection is also required for proper ow.

•Drainlinesshouldnotbepipeddirectlytothesewersystem.Anairgapofaminimumof

2 vertical inches (5 cm) should be between the end of the drain pipes from the icemaker,

dispenser unit/storage bin, and water-cooled condenser and the oor drain.

1. Icemaker

•Icemakerwatersupplyinletis1/2"femalepipethread(FPT).Aminimumof3/8"OD

copper tubing is recommended for the icemaker water supply line.

•Anicemakerwatersupplylineshut-offvalveanddrainvalveshouldbeinstalled.

•Icemakerdrainoutletis3/4"FPT.Aminimumof3/4"ODhardpipeisrecommendedfor

the icemaker drain line.

Inhaltsverzeichnis

Andere Hoshizaki Eiswürfelbereiter Handbücher

Hoshizaki

Hoshizaki F-1000MAF-C Bedienungsanleitung

Hoshizaki

Hoshizaki KM-600MAH Bedienungsanleitung

Hoshizaki

Hoshizaki DSM-12CE Bedienungsanleitung

Hoshizaki

Hoshizaki FM-600ALHE Bedienungsanleitung

Hoshizaki

Hoshizaki KM-901MAH Bedienungsanleitung

Hoshizaki

Hoshizaki DCM-300BAH Bedienungsanleitung

Hoshizaki

Hoshizaki KM-520MAJ-E Bedienungsanleitung

Hoshizaki

Hoshizaki FM-120KE Bedienungsanleitung

Hoshizaki

Hoshizaki IM-130ANE-HC Bedienungsanleitung

Hoshizaki

Hoshizaki KM-500MAF Bedienungsanleitung

Hoshizaki

Hoshizaki F-2000MRB Bedienungsanleitung

Hoshizaki

Hoshizaki KML-350MAF Bedienungsanleitung

Hoshizaki

Hoshizaki KM-2100SWH3 Betriebsanleitung

Hoshizaki

Hoshizaki DB-130H Bedienungsanleitung

Hoshizaki

Hoshizaki F-1100MWA Bedienungsanleitung

Hoshizaki

Hoshizaki KM-1340MAH Bedienungsanleitung

Hoshizaki

Hoshizaki AM-50BAE Handbuch

Hoshizaki

Hoshizaki KM-151BAW Bedienungsanleitung

Hoshizaki

Hoshizaki FM-2000ALE-N Bedienungsanleitung

Hoshizaki

Hoshizaki KM-1300NRF Bedienungsanleitung

Hoshizaki

Hoshizaki F-450MAH Bedienungsanleitung

Hoshizaki

Hoshizaki KM-320MAH Bedienungsanleitung

Hoshizaki

Hoshizaki KMD-210AB-HC Bedienungsanleitung

Hoshizaki

Hoshizaki DCM-270BAH-OS Bedienungsanleitung

Beliebte Eiswürfelbereiter Handbücher anderer Marken

Sub-Zero

Sub-Zero 315I Gebrauchsanweisung

Kenmore

Kenmore 2217402A Bedienungsanleitung

Cornelius

Cornelius WM600 Betriebsanleitung

GE XPIO43SCSS Bedienungsanleitung

Whynter

Whynter FIM-450HA Bedienungsanleitung

U-Line

U-Line UMCR014-SC01A Installationshandbuch

Andrew James

Andrew James AJ000522 Bedienungsanleitung

Scotsman

Scotsman CME1356 Bedienungsanleitung

Scotsman

Scotsman ACM 25 Bedienungsanleitung

Kärcher

Kärcher IP 120 Bedienungsanleitung

U-Line

U-Line SS1095 Bedienungsanleitung

Maytag

Maytag MIM1554WRS - Ice Maker Bedienungsanleitung

Princess

Princess Yonanas Bedienungsanleitung

Unold

Unold 48946 Bedienungsanleitung

Electrolux

Electrolux E15IM60GP Bedienungsanleitung

Cornelius

Cornelius UC150 ICE ONLY Bedienungsanleitung

Wessamat

Wessamat CombiLine W80 EL Bedienungsanleitung

Summit

Summit BIM68OSGDR Bedienungsanleitung