Hoshizaki SP-5550 Bedienungsanleitung

2A9766-010

Hoshizaki Push-Button to Opti-Serve Conversion Kit

SP-5550 and SP-5552

For Use with DCM-300BAH Auxiliary Code F-1 and Later,

DCM-500BAH and DCM-500BWH Auxiliary Code H-0 and Later,

DCM-751BAH, DCM-751BWH, and DCM-752BAH

Check to ensure that all parts are included:

Index

No. Description Model SP Kit Part Number Qty.

1Opti-Serve Apron Panel Assembly

(includes OS sensors with connectors)

DCM-300/500B_H SP-5550 1A6139A01 1

2Opti-Serve Apron Panel Assembly

(includes OS sensors with connectors)

DCM-751B_H

DCM-752BAH

SP-5552 1A6147A01 1

3 Plastic Insert All 4A0586-06 2

4Insulation Tubing All 7762-0717 1

5Nylon Tie All 8911-0200 6

6 Wiring Label All 3B0792-01 1

7 Conversion Label All 4A6944-01 1

WARNING

• Only qualied service technicians should install this kit to reduce the risk of death, electric shock, serious injury, or re.

• No service should be undertaken until the technician has thoroughly read these instructions. Failure to follow these instructions will adversely

affect safety, performance, component life, and warranty coverage and may result in costly water damage.

• To reduce the risk of electric shock, do not touch the power switch, control switch, or plug with damp hands.

• Before Servicing: Move the icemaker's power switch to the "OFF" position. Turn off the power supply. Place the disconnect (if applicable) in

the off position. Lockout/Tagout to prevent the power supply from being turned back on inadvertently.

• The manufacturer cannot be held responsible for injury or damage resulting from improper, incorrect, and unreasonable use or installation.

IMPORTANT

These SP kits are designed specically for use with control board; 2A4296-01, 2A8084-01, or 2A9093-01. The use of these SP kits with

a control board other than those listed is not permitted.

Push-Button Removal Instructions

1) Move the power switch to the "OFF" position, then turn off the power supply. Lockout/Tagout to prevent the power supply from being turned

back on inadvertently.

2) Remove the front panel. Unplug the push-button connector. See Fig. 1. Set the front panel aside.

3) Remove the control box cover. See Fig. 2.

4) Unplug the control board K7 ice and water push-button connectors. See Fig. 2. Using a nylon tie provided in this kit, secure the push-button

connectors in a safe out of the way location in the control box.

Control

Box Cover

Fig. 1

Push-Button

Connector

98765432 1

5VDC

Fig. 2

Control Box

Control

Board

Push-Button K7

Ice Connector

Push-Button K7

Water Connector

Front Panel

Control Box

2A9766-010

5) Disconnect the dispense mode switch wires (5VDC). See Fig. 3. Wrap each removed connector with electrical tape (not provided), then

secure the 3 wires together with a nylon tie provided in this kit in a safe out of the way location in the dispense mode switch area.

6) Remove the front panel push-button assembly from the push-button assembly bracket and discard. Remove the "ICE" and "WATER" labels

from the front panel. See Fig. 4.

7) Place the 2 plastic inserts provided in this kit into the holes in the front panel where the push buttons were located. Set the front panel aside.

8) Remove the apron panel and discard. See Fig. 5.

Opti-Serve Installation Instructions

9) Rest the opti-serve apron panel assembly provided in this kit, in its correct orientation on the drip tray (do not secure at this time), then route

the opti-serve sensor wires into the dispense mode switch area. See Fig. 6. Note: When routing the opti-serve sensor wires, route them to the

right side of the drain hose, then over the discharge line (not under) up into the dispense mode switch area.

10) Next, route the opti-serve control board K7 ice and water connectors into the control box through the plastic bushing. See Fig. 6.

Fig. 3

Drain Hose

Fig. 6

Fig. 4 Fig. 5

Discharge Line

Opti-Serve

Sensor Wires

Opti-Serve

Sensor Wires

Opti-Serve K7

Ice Connector

Opti-Serve K7

Water Connector

Dispense Mode

Switch

Dispense Mode

Switch Area

Opti-Serve

Apron Panel

Drip Tray

Plastic Bushing

Control Box

11) Connect the Opti-Serve ice and water connectors to the control board K7 connector. See Fig. 7.

Control Board

98765432 1

5VDC

Control Board Opti-Serve K7

Ice Connector

Opti-Serve K7

Water Connector

Fig. 7

Dispense Mode Switch

Push-Button

Assembly

Front Panel

ICE/WATER Labels

Plastic Inserts

Apron Panel

Dispense Mode Switch area

Push-Button

Assembly Bracket

2A9766-010

12) Route the opti-serve K7 ice connector terminal #2 yellow (Y) and the opti-serve K7 ice connector terminal #5 dark blue (DBU) out of the

control box through the plastic bushing down to the dispense mode switch. See Fig. 6.

13) Connect the opti-serve K7 ice connector terminal #2 yellow (Y) to the dispense mode switch terminal #1, connect the opti-serve K7 ice

connector terminal #5 dark blue (DBU) to the dispense mode switch terminal #3, and the opti-serve ice dispenser sensor wire connector

violet (V) wire (from middle connector) to the dispense mode switch terminal #2. See Fig. 7.

Fig. 7

14) Place the pipe insulation provided in this kit on the liquid line as shown in Fig. 8. and secure with one of the nylon ties provided in this kit.

IMPORTANT! Failure to install the liquid line pipe insulation could cause damage to the opti-serve sensor wires.

15) Secure the opti-serve sensor wires with one of the nylon ties provided in this kit to the pipe insulation installed in step 14. Note: Be sure to

leave enough slack in the opti-serve sensor wires for future opti-serve apron panel removal.

Dispense Mode Switch

1-Yellow (Y)

2-Violet (V)

3-Dark Blue (DBU)

16) Bundle the opti-serve sensor wires together and secure them within the appliance using nylon ties provided in this kit.

17) Place and secure the opti-serve apron panel in its correct position.

18) Place the wiring label provided in this kit under the wiring label on the back of the front panel. Next, place the conversion label provided in

this kit on the back of the icemaker below the nameplate.

19) Conrm the control switch is in the "ICE" position, then replace the control box cover and front panel in their correct positions.

20) Turn the power supply on, then move the power switch to the "ON" position and conrm operation.

21) Conrm water and ice opti-serve sensor operation. Be sure to check the ice sensor with the dispense mode switch in both the

"CONTINUOUS" and "PORTION" positions.

Fig. 8

Pipe Insulation

Opti-Serve Wiring Label

Opti-Serve

Sensor Wires

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hoshizaki Kühlschrankteile & Zubehör Handbücher

Hoshizaki

Hoshizaki HS-5243 Bedienungsanleitung

Beliebte Kühlschrankteile & Zubehör Handbücher anderer Marken

BEST BUY essentials

BEST BUY essentials BE-SSHQ531 Bedienungsanleitung

Carrier TRANSICOLD

Carrier TRANSICOLD 69NT40-531 Series Bedienungsanleitung

Manitowoc

Manitowoc K00221 Bedienungsanleitung

GEA

GEA 402 UVR Bedienungsanleitung

Pentair

Pentair Condensate Neutralization kit Bedienungsanleitung

Silver King

Silver King SKRS28-ESUS10 Kurzanleitung

VESTEL

VESTEL 466-ELECTRONIC Bedienungsanleitung

Dometic

Dometic 3311145.000 Original Betriebsanleitung

Best Buy

Best Buy Essentials BE-LGLT800P531 Bedienungsanleitung

Dometic

Dometic 3108705.272 Leitfaden

DS Produkte

DS Produkte 06130 Bedienungsanleitung

Frigidaire

Frigidaire DUOTRIMKIT Bedienungsanleitung

Samsung

Samsung MXJ-YA1509M Bedienungsanleitung

Viking Range

Viking Range 3 Series Bedienungsanleitung

Ice-O-Matic

Ice-O-Matic KCUBEDISP Bedienungsanleitung

Ironman4x4

Ironman4x4 IFRIDGESLIDE012 Bedienungsanleitung

edenox

edenox 2GN Bedienungsanleitung

Rivacold

Rivacold FS Series Handbuch