HP 3COM Etherlink III 3C590 PCI 10BT Bedienungsanleitung

3COM Etherlink III 3C590 PCI 10BT

Network Adapter

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

General information to read before installing

On all systems : before installing LAN card, go into Bios setup and set PnP OS field to NO.

• How to change LAN card configuration if needed (Advanced users only)

This is a general advisory on how to forcibly modify resources for ISA and PCI network

cards.

ISA cards:

• For ISA network adapters, start the configuration tool provided in driver

kit (See install documentation)

• Under CMOS setup, go to Advanced > PnP/PCI ISA IRQ Resource Exclu-

sion > reserve an IRQ for the adapter.

PCI cards:

• For PCI network adapters, go to CMOS setup > Advanced > PnP/PCI ISA

IRQ Resource Exclusion > reserve the IRQ for Legacy ISA.

• ISA cards can’t use IRQ9

• IRQ 9 is reported as being used by ACPI during POST. This is due to ISA’s

inability to share IRQs.

• Using a different IRQ (e.g. 5, 7, 10, and 11) will work. For this:

1Install the NIC then power up the system.

2Press F2 to go to CMOS setup.

3Set PnP OS to NO and reserve IRQ 5, 7, 10, or 11 (explained in installation

section)

4Save the configuration settings and boot to the applicable OS.

5Follow installation steps.

Sound conflict under Win 95 on VLi8 only

• On VLi8, LAN cards cause an IRQ conflict with the embedded sound de-

vice under Win95.

• To solve the problem: Reserve IRQ 5 and sett PNP OS to no. For this:

1Install the NIC then power up the system

General information to read before installing

2Press F2 to go to CMOS setup.

3Set PNP OS to NO and reserve IRQ 5.

4Save settings and boot to applicable OS.

1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter

Microsoft Windows 95 SR2.5

1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network

Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 3.51 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• 3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver-

sion 5.2.2.

• Driver File: EL59X.SYS, version 1.22

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT 3.51 Server system that supports NetBEUI,

NWLink IPX/SPX Compatible Transport and NWLink NetBIOS network

protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the 3COM 3C590 network adapter

into a PCI slot.

2Connect network cable media to the 3COM 3C590 network adapter.

3Reboot the system to Windows 95SR2.5.

4Windows 95SR2.5 will automatically recognize the 3COM 3C590 network

adapter as “3Com 3C590 EtherLink III”.

5Insert the 3COM 3C590 driver disk in the floppy drive and click on “Next”

from the Update Device Driver Wizard dialog box.

6When Windows 95 detects the updated driver, “3Com EtherLink III

3C590”, click on “Finish”.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 5 03 07

I/O Address 210 210 210

1 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter

Connecting to a Windows NT 3.51 Server

7During the Update Device Driver process, point to the appropriate file

locations (i.e. drivers disk or Windows 95 CD) to install the necessary

files. Keep newer files when a file being copied is older than the file

currently on your computer.

8Click on “OK” when the system prompts for the computer and workgroup

names.

9Enter the Computer Name, Workgroup, and Computer Description in the

appropriate spaces and click on “Close” (Contact your network

administrator if you do not have the required information).

10 Click on “YES” to restart the system when prompted.

11 Right-click on the “Network Neighborhood” icon and select “Properties”.

12 Accept the default Network Protocols and the Primary Network Logon

(Client for Microsoft Networks) as seen below and click on “OK”. (If you

do not have the required information, contact your network

administrator)

13 Client for Microsoft Networks

Client for Microsoft Networks

3Com EtherLink III

3Com TCAATDI Diagnostic TDI

IPX/SPX-compatible Protocol

NetBEUI

14 Click on “OK” to accept the configuration.

15 When prompted, specify the path to your Windows 95 files.

16 Click on “Yes” when prompted to restart the system.

2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter

Microsoft Windows 95 SR2.5

2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network

Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 4.0 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• 3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver-

sion 5.2.2.

• Driver File: EL59X.SYS, version 1.22

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink

IPX/SPX Compatible Transport and NWLink NetBIOS network protocols.

• Device Configuration

Procedure

1With the HP Vectra turned off, install the 3COM 3C590 network adapter

into a PCI slot.

2Connect network cable media to the 3COM 3C590 network adapter.

3Reboot the system to Windows 95SR2.5.

4Windows 95SR2.5 will automatically recognize the 3COM 3C590 network

card as “3Com 3C590 EtherLink III”.

5Insert the 3COM 3C590 driver disk in the floppy drive and click on “Next”

from the Update Device Driver Wizard dialog box.

6When Windows 95 detects the updated driver, “3Com EtherLink III

3C590”, click on “Finish”.

7During the Update Device Driver process, point to the appropriate file

locations (i.e. drivers disk or Windows 95 CD) to install the necessary

files. Keep newer files when a file being copied is older than the file

currently on your computer.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 05 03 07

I/O Address 210 210 210

2 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter

Connecting to a Windows NT 4.0 Server

8Click on “OK” when the system prompts for the computer and workgroup

names.

9Enter the Computer Name, Workgroup, and Computer Description in the

appropriate spaces and click on “Close” (Contact your network

administrator if you do not have the required information).

10 Click on “YES” to restart the system when prompted.

11 Right-click on the “Network Neighborhood” icon and select “Properties”.

12 Accept the default Network Protocols and the Primary Network Logon

(Client for Microsoft Networks) as seen below and click on “OK”. (If you

do not have the required information, contact your network

administrator)

13 Client for Microsoft Networks

Client for Microsoft Networks

3Com EtherLink III

3Com TCAATDI Diagnostic TDI

IPX/SPX-compatible Protocol

NetBEUI

14 Click on “OK” to accept the configuration.

15 When prompted, specify the path to your Windows 95 files.

16 Click on “Yes” when prompted to restart the system.

3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter

Microsoft Windows 95 SR2.5

3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network

Adapter

Microsoft Windows 95

SR2.5

Connecting to a Netware

3.12 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• 3COM Etherlink III 3C590 PCI 10BT network adapter and driver disk ver-

sion 5.2.2.

• Driver File: EL59X.SYS, version 1.22

• Microsoft Windows 95 SR2.5 media.

• Novell Netware 3.12 Server that supports IPX network protocol.

• Novell Client for Windows 95 v2.5 installation media.

Device Configuration

Procedure

1With the HP Vectra turned off, install the 3COM 3C590 network adapter

into a PCI slot.

2Connect network cable media to the 3COM 3C590 network adapter.

3Reboot the system to Windows 95SR2.5.

4Windows 95SR2.5 will automatically recognize the 3COM 3C590 network

adapter as “3Com 3C590 EtherLink III”.

5Insert the 3COM 3C590 driver disk in the floppy drive and click on “Next”

from the Update Device Driver Wizard dialog box.

6When Windows 95 detects the updated driver, “3Com EtherLink III

3C590”, click on “Finish”.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 5 03 07

I/O Address 210 210 210

3 Installing the 3COM Etherlink III 3C590 PCI 10BT Network Adapter

Connecting to a Netware 3.12 Server

7During the Update Device Driver process, point to the appropriate file

locations (i.e. drivers disk or Windows 95 CD) to install the necessary

files. Keep newer files when a file being copied is older than the file

currently on your computer.

8Click on “OK” when the system prompts for the computer and workgroup

names.

9Enter the Computer Name, Workgroup, and Computer Description in the

appropriate spaces and click on “Close” (Contact your network

administrator if you do not have the required information).

10 Click on “YES” to restart the system when prompted.

11 From the location of the “Novell Client for Windows 95 v.2.5” installation

files, execute “Setup.exe”.

12 Click on “Yes” to accept the License Agreement.

13 Select “Custom” installation and click on “Next”.

14 Select “Bindery (NetWare 3.x)” and click on “Next”.

15 Click on “Install” to start the installation.

16 Click on “Yes” to set the Preferred Server. (If you do not have the

required information, contact your network administrator).

17 Click on “Reboot” to complete the installation.

18 Right-click on the “Network Neighborhood” icon and select “Properties”.

19 Accept the default Network Protocols and the Primary Network Logon to

(Novell NetWare Client) as seen below and click on “OK”. (If you do not

have the required information, contact your network administrator)

20 Novell NetWare Client

Novell NetWare Client

3COM Etherlink III Bus-Master PCI Ethernet Adapter

IPX 32-bit Protocol for the Novell NetWare Client

IPX/SPX-compatible Protocol

NetBEUI

21 When prompted, specify the path to your Windows 95 files.

22 Click on “Yes” when prompted to restart the system.

Dieses Handbuch passt für folgende Modelle

Andere HP Adapter Handbücher

HP 90W Bedienungsanleitung

HP Nc551m Gebrauchsanweisung

HP HP 3005PR Bedienungsanleitung

HP 4X - DDR InfiniBand Mezzanine HCA Merkblatt

HP 90W Bedienungsanleitung

HP StoreFabric CN1100R Bedienungsanleitung

HP VL600 - Vectra - 128 MB RAM Bedienungsanleitung

HP 331FLR Bedienungsanleitung

HP 530SFP+ Bedienungsanleitung

HP StorageWorks FCA2684DC Bedienungsanleitung

HP Model 744 - VME Workstation Referenzhandbuch

HP 560FLR-SFP+ Bedienungsanleitung

HP NC7771 Bedienungsanleitung

HP 652503-B21 Bedienungsanleitung

HP NC553m Gebrauchsanweisung

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP NC364T Bedienungsanleitung

HP 665249-B21 Bedienungsanleitung

HP NC550m Gebrauchsanweisung

HP 41802A Kurzanleitung

HP 381513-B21 - Smart Array P800 Controller... Bedienungsanleitung

HP 650926-B21 Bedienungsanleitung

HP Bt500 Bedienungsanleitung

HP NC373F Gebrauchsanweisung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung