HP Integrity rx1600 Bedienungsanleitung

February 2004

Printed in the U.S.A.

Smart Array (A9890A) Cable Routing

The purpose of this document is to provide cable routing information when a Smart Array PCI-X RAID card (A9890A)

is used to drive the embedded hard disk drives. The existing SCSI cable connected to the Channel A connector on the

system board is relocated to the Channel A connector on the Smart Array PCI-X card installed in slot 1 (full-length slot)

of the PCI cage.

The SCSI cable is routed from the PCI cage under the power supply bracket and over the IDE cable, if installed, avoiding

blocking the airflow of the chassis fans.

Refer to the hp integrity rx1600 Operation and Maintenance Guide for detailed instructions on powering down the

server, extending the server from a rack, and removing and replacing covers and components.

1. Disconnect the SCSI cable from the Channel A connector on the system board by pulling on the cable release strap.

See figure 1.

Figure 1. SCSI Channel A Connector on System Board

2. Remove the PCI cage from the server.

3. Remove any accessory card installed in PCI slot 2 (half-length slot).

4. Install the Smart Array PCI-X RAID card (A9890A) in PCI slot 1 (full-length slot).

5. Orient the PCI cage with the installed PCI-X RAID card component-side-up allowing routing of the SCSI cable.

See figure 2.

Figure 2. Cable Routing on Smart Array Card and PCI Cage

NOTE If an optional management processor card is installed in the server, follow the

instructions provided in the hp integrity rx1600 Operation and Maintenance Guide to

remove the card, allowing access to the Channel A connector. Reinstall the card after the

SCSI cable has been disconnected.

Channel A

connector

Around heatsink

Exit parallel to

connector

Channel A1

Under slot 2 connector

6. Attach the SCSI Channel A connector (previously removed from the system board connector) to the A1 Channel of

the PCI-X RAID card.

7. Route the SCSI cable around the heatsink on the PCI-X RAID card and under the edge of the PCI slot 2 connector.

See figure 2.

8. Continue routing the cable parallel to the connector edge of the PCI cage.

9. Reinstall any accessory card previously removed from PCI slot 2.

10. Install the PCI cage into the server chassis.

11. Route the SCSI cable under the power supply bracket as shown in figure 3.

Figure 3. Route Cable under Power Supply Bracket

12. Route the SCSI cable through the access slot of the fan assembly to the connector on the SCSI backplane.

See figure 4.

Figure 4. Cable Routing at SCSI Cage

13. Complete the installation by following the instructions provided in the hp integrity rx1600 Operation and

Maintenance Guide for closing up the server, installing in a rack, and powering-up. To enable RAID refer to the

A9890A documentation.

NOTE The SCSI cable should be routed over the IDE cable if the IDE cable is present.

CAUTION Do not block the airflow of the chassis fans. Reduced airflow may cause overheating.

Power Supply

Bracket

Route over IDE

cable (if present)

Do not block fans

Andere Handbücher für Integrity rx1600

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Computerhardware Handbücher

HP HPE LSWM2XGT2PM Bedienungsanleitung

HP 64793 Series Bedienungsanleitung

HP 81200 Bedienungsanleitung

HP F768WM Bedienungsanleitung

HP MPIO Installations- und Betriebsanleitung

HP Model 744 - VME Workstation Bedienungsanleitung

HP 405132-B21 Bedienungsanleitung

HP ML570 - ProLiant - G2 Bedienungsanleitung

HP Wireless USB Network Adapter hn215w Bedienungsanleitung

HP 8168E Bedienungsanleitung

HP Integrity rx8620 Bedienungsanleitung

HP AB479A Bedienungsanleitung

HP OmniBook 3100 Bedienungsanleitung

HP Z400 - Workstation Bedienungsanleitung

HP AF079A Installationsanleitung

HP Xw4600 - Workstation - 2 GB RAM Bedienungsanleitung

HP QUERY Bedienungsanleitung

HP MPEGscope Portable Benutzerhandbuch

HP SC08Ge Bedienungsanleitung

HP Model 744 - VME Workstation Bedienungsanleitung

HP Adaptive Rack Cooling System Benutzerhandbuch

HP Apollo r2800 Montageanleitung

HP 4440B Bedienungsanleitung

HP QMH2672 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung