HP ProCurve MSM765zl Bedienungsanleitung

ProCurve MSM765zl Mobility Controller

Installation and Getting Started Guide

MSM765-IGSG-5992-5964.book Page 1 Thursday, April 2, 2009 6:48 PM

MSM765-IGSG-5992-5964.book Page 2 Thursday, April 2, 2009 6:48 PM

HP ProCurve MSM765zl

Mobility Controller

Installation and Getting Started Guide

MSM765-IGSG-5992-5964.book Page i Thursday, April 2, 2009 6:48 PM

Hewlett-Packard Company

8000 Foothills Boulevard, m/s 5552

Roseville, California 95747-5552

http://www.procurve.com

Publication Number

5992-5964

April 2009

Applicable Products

Software Credits and Notices

SSL on HP ProCurve Switches is based on the OpenSSL

software toolkit. This product includes software developed

by the OpenSSL Project for use in the OpenSSL Toolkit. For

more information on OpenSSL, visit www.openssl.org.

Disclaimer

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY

OF ANY KIND WITH REGARD TO THIS MATERIAL,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not

be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing,

performance, or use of this material.

The information contained herein is subject to change

without notice. The only warranties for HP products and

services are set forth in the express warranty statements

accompanying such products and services. Nothing herein

should be construed as constituting an additional warranty.

HP shall not be liable for technical or editorial errors or

omissions contained herein.

Hewlett-Packard assumes no responsibility for the use or

reliability of its software on equipment that is not furnished

by Hewlett-Packard.

Warranty

See the Customer Support/Warranty booklet included with

the product.

A copy of the specific warranty terms applicable to your

Hewlett-Packard products and replacement parts can be

obtained from your HP Sales and Service Office or

Safety

Before installing and operating these products, please read

the “Installation Precautions” in chapter 1, and the safety

statements in Appendix A, “EMC Regulatory Statements”.

Web Version of this Document

The printed version of this document that was shipped with

the HP ProCurve MSM765zl contains the latest information

at time of printing. To view or download the latest version of

this document and other documentation, visit:

www.procurve.com/customercare/support/manuals/index.htm.

HP ProCurve MSM765zl Mobility Controller J9370A

HP ProCurve Switch 5406zl J8697A

HP ProCurve Switch 5406zl-48G J8699A

HP ProCurve Switch 5412zl J8698A

HP ProCurve Switch 5412zl-96G J8700A

HP ProCurve Switch 8212zl J8715A

MSM765-IGSG-5992-5964.book Page ii Thursday, April 2, 2009 6:48 PM

Contents

1 Hardware Installation

MSM765zl Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Installing the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Verifying the MSM765zl is Installed Correctly . . . . . . . . . . . . . . . . . . . . 1-4

Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

2 Getting Started

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Connect to the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Verify Switch Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Activate the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Obtain the Activation Hardware ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Install the Product License Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Configure the Switch for the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

About MSM765zl Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Initial MSM765zl Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Determine Switch Index of the MSM765zl . . . . . . . . . . . . . . . . . . . . . . 2-10

Assign an IP Address to the MSM765zl LAN Port . . . . . . . . . . . . . . . . 2-11

Configure the MSM765zl Internet Port . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Restarting and Resetting the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Restarting the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Resetting an MSM765zl to Factory Defaults . . . . . . . . . . . . . . . . . . . . 2-16

3 Troubleshooting

HP Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

MSM765-IGSG-5992-5964.book Page 1 Thursday, April 2, 2009 6:48 PM

A EMC Regulatory Statements

U.S.A. - FCC Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Australia/New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Japan - VCCI Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

B Waste Electrical and Electronic Equipment (WEEE)

Statements

C Hardware Components

Front Panel Port and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

Replacing or Removing an MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

Replacing the Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5

Replacing the Flash Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6

Index

MSM765-IGSG-5992-5964.book Page 2 Thursday, April 2, 2009 6:48 PM

1-1

Hardware Installation

MSM765zl Overview

The HP ProCurve Networking MSM765zl Mobility Controller is a Services zl

Module-based WLAN controller. It plugs in to either the 5400zl or 8212zl

switches. The MSM765zl Mobility Controller is referred to in this document

as the MSM765zl. New switches need to be prepared according to their

supplied documentation.

A maximum of four MSM765zls can be installed in the same chassis. Under

certain conditions, a maximum of three MSM765zls are supported in the 5406zl

chassis. See “Environmental Specifications” on page 1-5.

Figure 1. Front panel of the MSM765zl

See also “Front Panel Port and LEDs” on page C-1.

Note This manual contains the basic information needed to get you started using

the MSM765zl. It also contains EMC Regulatory Statements (Appendix A) and

Waste Electrical and Electronic Equipment (WEEE) Statements (Appendix

B). Appendix C provides hardware component information.

For more information on working with the MSM765zl, see the MSM7xx

Controllers Management and Configuration Guide. The latest version of this

and all HP ProCurve Networking documentation is available at:

www.procurve.com/customercare/support/manuals/index.htm.

MSM765zl Locator LED

HDD and CF Status LEDs

HDD and Network

activity LEDs USB port

Module Status LED

MSM765-IGSG-5992-5964.book Page 1 Thursday, April 2, 2009 6:48 PM

1-2

Hardware Installation

Installing the MSM765zl

To install the MSM765zl into a switch, the switch can be powered on or off.

The following procedure assumes the switch is powered on.

Installation Procedure

1. Use a Torx T-10 or flat-bladed screwdriver to unscrew the screws in the

cover plate over the slot where the MSM765zl is to be installed. Remove

the cover, and store the cover plate for possible future use.

2. Hold the MSM765zl by its bulkhead—taking care not to touch the metal

connectors or components on the board.

3. Open the extractor handles.

Installation Precautions

■Static electricity can severely damage the electronic components on the

MSM765zl. When handling and installing the MSM765zl, follow these

procedures to avoid damage from static electricity:

• Handle the MSM765zl by its bulkhead or edges and avoid touching

the components and the circuitry on the board.

• When installing the MSM765zl, equalize any static charge difference

between your body and the switch by wearing a grounding wrist

strap and attaching it to the switch’s metal body, or by frequently

touching the switch’s metal body.

■The MSM765zl has “low-force”, high-performance connectors. High

insertion forces are not necessary to install the MSM765zl, and should

not be used.

■Ensure the MSM765zl is fully inserted. Press the MSM765zl into the

slot until the bulkhead on the MSM765zl contacts or is very close to

contacting the front face of the switch chassis.

■Once the MSM765zl is fully inserted, screw in the two retaining screws

to secure the MSM765zl in place.

■For safe operation, proper switch cooling, and reduction of electromag-

netic emissions, ensure that a slot cover is installed on any unused

MSM765zl slot. For safety, no more than one slot should be uncovered

at a time when the switch is powered on.

■Respect the temperature specifications for the MSM765zl.

MSM765-IGSG-5992-5964.book Page 2 Thursday, April 2, 2009 6:48 PM

1-3

Hardware Installation

Installing the MSM765zl

4. Insert the MSM765zl aligning with the guides in the slot, and slide it into

the slot until it is fully inserted.

5. Once the contacts have engaged, use the extractor handles to seat the

MSM765zl completely.

6. Tighten the screws.

Figure 2. MSM765zl being installed

Insert MSM765zl into the guides and slide in until fully

inserted.

Open extractor handles

MSM765-IGSG-5992-5964.book Page 3 Thursday, April 2, 2009 6:48 PM

1-4

Hardware Installation

Installing the MSM765zl

Verifying the MSM765zl is Installed Correctly

When the MSM765zl is installed properly, it undergoes a self test that takes a

few seconds. This happens both when the switch is powered on after installing

the MSM765zl, and when the MSM765zl is installed while the switch already

has power. The LEDs help determine if the MSM765zl has passed the self test,

as described in the following table.

Error Conditions

Error conditions indicated by the MSM765zl LEDs are described in “Front

Panel Port and LEDs” on page C-1.

Note Allow sufficient time for the MSM765zl to start up, or you will receive an error

message.

LED Location

of LED Display for a Properly Installed MSM765zl

Test Switch ON briefly while the MSM765zl is undergoing self test, then OFF.

Note:Ifthe MSM765zl wasinstalledwith the switch powered off,

and then the switch was powered on, the Test LED will stay ON

for the duration of the switch self test.

Figure 6 on page C-4 and Figure 7 on page C-4 show the location

of the Test, Fault, and MSM765zl StatusLEDs on a 5400zl or 8212zl

series switch, respectively.

Fault Switch OFF

Module

Status Switch The LED goes ON as soon as the MSM765zl is installed and the

switch is powered on, and stays ON steadily.

Module

Status MSM765zl The LED blinks green during initialization. Solid green means that

MSM765zl is operational.

Figure 1 on page 1-1 shows the location of all MSM765zl LEDs.

HDDandCF

Status MSM765zl The LED goes ON when HDD/CF initialization was successful. It

is OFF by default.

MSM765-IGSG-5992-5964.book Page 4 Thursday, April 2, 2009 6:48 PM

Andere Handbücher für ProCurve MSM765zl

Inhaltsverzeichnis

Andere HP Controller Handbücher

HP MSM7XX Bedienungsanleitung

HP StorageWorks P2000 Bedienungsanleitung

HP ProLiant DL160se - G6 Server Bedienungsanleitung

HP HPE MR Gen11 Bedienungsanleitung

HP VXI Pentium 75000 Series Bedienungsanleitung

HP ProCurve MSM760 Bedienungsanleitung

HP Smart Array E500 Controller Gebrauchsanweisung

HP StorageWorks ESL E Series Bedienungsanleitung

HP Smart Array P212 Bedienungsanleitung

HP Compaq Presario,Presario 4400 Leitfaden

HP Aruba 7024 Benutzerhandbuch

HP 615418-B21 Bedienungsanleitung

HP ProCurve MSM750 Bedienungsanleitung

HP MSA 2040 Bedienungsanleitung

HP 166207-B21 - Smart Array 5302/32 RAID... Bedienungsanleitung

HP MSM720 Bedienungsanleitung

HP HSG80 - StorageWorks RAID Array Controller Handbuch

HP ProCurve 800 Handbuch

HP ProCurve MSM765zl Bedienungsanleitung

HP Smart Array P712m Gebrauchsanweisung

HP Smart Array P830 Bedienungsanleitung

HP MR Gen10 Plus Bedienungsanleitung

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

HP MSA 2040 Leitfaden

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch