HP D6030A - NetServer - E50 Bedienungsanleitung

HP NetServer E 30

Windows NT 4.0 Installation Guide

This document presents the most important information that you need to install

Windows NT version 4.0. Please check with HP Support for information regarding

newer versions of Windows NT after they are released by Microsoft.. The first section

of this document is a list of helpful tips on Windows NT installation. The second

section is a step-by-step installation guide. Please see the CD-ROM-based HP

Information Assistant for additional detailed information to help you install Windows

NT.

Table of Contents

Section 1. Installation Tips

Extended Translation

Troubleshooting Host Adapter Configuration

DAT Drive

Boot Partition

Windows NT Setup Utility

BusTech SCSI Controller

Windows NT Installation Tips

Section 2. Windows NT 4.0 Installation Guide

Configuring Logical Disk Size for the Disk Array Controller

Booting from the Embedded SCSI Controller

Installing Windows NT 4.0

Upgrading to Windows NT 4.0

Section 3. Troubleshooting

Section 4. On-Line Information and Software Sources

Section 5. HP NetServer CD Status Report

Section 6. HP Information Assistant

Section 1. Installation Tips

Extended Translation

Run SCSI-Select and enable "Extended Translation for Drives larger than 1 GB." For

the bundled SCSI controller and certain Adaptec SCSI controllers (for example the

Adaptec AHA 2940) the "Extended Translation option" can be enabled from the SCSI-

Select menu. SCSI-Select is available by pressing Ctrl-A during system boot. The

factory default for the bundled SCSI controller is Extended Translation Enabled.

Troubleshooting Host Adapter Configuration

The boot manager for Windows NT contains recovery logic to allow you to return to

the last known good configuration. If you have changed your host adapter

configuration and Windows NT no longer boots, follow these steps to recover:

1. Undo any hardware changes you have made to the computer since it was

last operational.

2. Reboot the computer. Watch the display carefully during bootup. If the

message "Press spacebar NOW to invoke the Last Known Good menu"

appears, press the spacebar and follow the instructions on the screen to

continue booting with the last known good configuration.

NOTE Do not log in if you pass the "Press spacebar NOW to

invoke the Last Known Good screen" option, because this

will wipe out the configuration you want.

3. Once your computer is operational again, double check all of the hardware

and software configuration changes you wish to make. Look specifically for

conflicts with parts of the existing system configuration that are not being

changed. If you cannot determine the source of the error, contact the host

adapter vendor or HP Technical Support for assistance.

DAT Drive

If the DAT drive is attached to the bundled SCSI controller, be sure to remove the

DAT drive SCSI terminator; the SCSI cable is self-terminated. Refer to the DAT drive

manual for instructions on removing the terminator.

Boot Partition

If the system boots from the Disk Array controller, ensure that the first logical drive

created by the JetSet Utility is 2048 MB or less. The bundled SCSI controller has an

8 GB limit for the boot partition.

Windows NT Setup Utility

Windows NT Setup is a great tool for verifying device configuration and driver version

in the case of disk array or SCSI problems

BusTech SCSI Controller

The BusTech SCSI controller autoloads its own ASPI layer and can have only one.

Thus, it is incompatible with the bundled SCSI controller.

Windows NT Installation Tips

HP strongly recommends that you use only devices that are on the Microsoft

Windows NT Hardware compatibility List.

You must use Windows NT drivers ONLY.

Drivers from other operating systems such as Windows 3.1 or DOS will not work.

Section 2. Windows NT 4.0 Installation Guide

Before installing the Operating System, please read this section carefully.

Configuring Logical Disk Size for the Disk Array Controller

During system configuration, the Jet Set Utility on the HP NetServer Navigator CD-

ROM helps you set logical disk size in the Disk Array Configuration process. If the

boot drive is on the Disk Array Controller, set the logical disk size of the boot partition

to 2048 MB or less.

Booting from the Embedded SCSI Controller

Non-disk array systems boot from the drive with the lowest SCSI address. HP

recommends SCSI ID 0 for the boot drive. If you configure the boot drive with

another SCSI ID, your system may not boot when additional SCSI drives are

installed.

Installing Windows NT 4.0

1. Boot the HP NetServer using the HP NetServer Navigator CD-ROM. Run

Configuration Assistant and follow the instructions to create a driver

diskette. The diskette is created as part of Express Configuration. You

can also create the diskette via the Custom Configuration option or the

Diskette Library. In the Diskette Library, select the diskette labeled "HP

NetServer E 30 MS-Windows NT Drivers Diskette." Label the diskette "HP

NetServer MS-Windows NT Drivers Diskette" using the label shipped with

the system. This procedure refers to this diskette as the "Drivers Diskette".

2. Boot the system using the Windows NT Setup/Boot Diskette. Important:

Do not have the Windows NT 4.0 CD-ROM in the drive while booting the

system. Otherwise, the system may display an error message "BOOT:

Couldn’t find NTLDR." If this occurs, simply remove the CD-ROM and

reboot the system.

3. Install Windows NT using the diskettes shipped in the Microsoft Windows

NT package. Follow the Windows NT installation procedures and select

Custom setup.

4. At the next screen where Windows NT would auto detect Mass Storage

Controllers, press S to "Skip SCSI drivers and Mass Storage Detection."

5. At the next screen, press S again to configure additional SCSI adapters.

The Windows NT installer displays a list of options. Select "Other

(Requires Disk provided by a hardware manufacturer)."

6. The installation program prompts you to insert the "Manufacturer-supplied

hardware support disk" into drive A. Insert the Drivers Diskette and press

enter.

7. A window displays "Adaptec AHA-2940 / AIC 78xx NT". Select this driver

and press Enter to install. This driver supports the SCSI Controller

bundled in your HP NetServer E 30 and the Adaptec 2940 Controller..

After the SCSI driver is installed, press S again and use the UP and

DOWN arrow keys to select the driver "IDE CD-ROM (ATAPI 1.2)/Dual-

channel PCI IDE Controller." Press Enter to install. This driver supports

the IDE CD-ROM drive bundled in your HP NetServer E 30, and other

connected IDE hard drives.

Repeat step 5. Select the "Hewlett-Packard Disk Array Driver" if your

system has the HP Disk Array Controller. Press Enter to install.

NOTE HP recommends that you install the driver for the booting

controller first. The driver installation sequence above

assumes that the boot drive is attached to the bundled

SCSI controller.

8. Continue with the Windows NT Installation. Refer to the Microsoft

Windows NT Installation Guide for additional information. When the

system asks you to remove the diskette from drive A: and press ENTER to

continue, make sure to remove the Windows NT 4.0 CD-ROM from the

CD-ROM drive first. It is okay to continue the installation without the CD-

ROM in the drive. Windows NT will prompt for it later. When you insert the

CD-ROM, wait 10 seconds for the spin-up time before hitting OK to

continue with the installation.

NOTE If the boot drive is new or has just been initialized,

Windows NT may hang while booting from the hard drive.

Please see the troubleshooting section for a solution.

9. During the Network Installation, the automatic Network Adapter detection

may not detect the Network Adapter in your NetServer. You need to

manual select the Network Adapter type from the list. The bundled

Network Adapter in your NetServer is either the Hewlett-Packard

DeskDirect J2970A or J2973A.

You can determine which version of the HP DeskDirect Adapter is installed

in the NetServer by looking at the Adapter’s back panel. The J2970A has a

10BaseT and a 10Base2 connectors on the back panel. The J2973A has

only a 10BaseT connector. You can also look for the Adapter model

number on the card itself.

Upgrading to Windows NT 4.0

Follow the instructions from the section "Installing Windows NT 4.0." Make sure to

select the upgrade option.

Section 3. Troubleshooting

1. If the boot drive is new or just initialized, Windows NT may give a warning

message about disk drives having more than 1024 cylinders during the first

reboot from the hard drive. Windows NT may hang just after the SCSI BIOS

or Disk Array BIOS banner.

Fix: In some situations, the Windows NT installation program may detect the

hard drive geometry incorrectly, and thus limit the initial drive partition size to

1024 MB or hang while rebooting. To correct this problem, perform one-not

both-of the following:

(Be sure to enable extended translation for SCSI controllers)

Before starting Windows NT installation, follow these steps:

A. Boot into MS-DOS.

B. Run FDISK and FORMAT on the boot partition under DOS.

C. Install Windows NT. During Windows NT Installation, you may delete

and resize the MS-DOS partition created previously.

Alternately:

In the Windows NT installation program:

A. Partition the primary partition to 1024 MB.

B. Format the primary partition using FAT.

C. Press F3 to quit the installation program.

D. Restart the installation program.

E. At the drive partition screen, delete the 1024 MB primary partition.

F. Partition the primary partition to any desired size up to the drive

capacity.

G. Continue with the Windows NT installation program.

2. If the Network Adapter driver fails to start or does not appear to be working

correctly, examine the Event Log for any driver diagnostic messages.

A. Start the Event Viewer applet in the Administrative Tools group in

Program Manager.

B. Search the Event Log Source column for any entries named "Hpddnd3."

C. Double click on the entry to examine the Event Detail dialog box. The

upper half of the box gives a short generic description of the error. The

lower half of the box is a hex and ASCII dump of error data.

D. Scroll through the error data in ASCII for any readable strings.

E. If a readable string is present, it will describe the problem in more detail.

F. If no readable string is present, this typically indicates that the driver

failed early in the process of loading-usually due to a resource conflict

(for example, an I/O port conflict).

NOTE Make sure the Network Adapter is connected to a working

hub and verify that the LED is lit. Otherwise, the Network

Driver may not install.

3. Configure and test the HP DeskDirect Adapter.

Reconnect power to the computer and boot DOS. Run the LAN adapter

configuration utility on the HP PCI LAN Adapter Support Disk. For example, if

the Support Disk is in drive A, execute the following commands at the DOS

prompt: (You can create the HP LAN Adapter Support Disk from the Diskette

Library)

HPVGSET

If you wish to use the adapter in full duplex mode, use HPVGSET to enable

that option now.

Select "Card Test" to verify the adapter. After it passes, select "Exit program."

Connect the LAN cable to the HP DeskDirect Adapter.

4. If Windows NT asks for more Installation Diskettes than you have, e.g. asking

for Diskette #4 when you only have up to Diskette #3, make sure that the IDE

driver is installed properly. See step #7 for instructions.

5. If your system does not boot, and the screen displays an error message

"BOOT: Couldn’t find NTLDR," remove the Windows NT CD-ROM from the

drive and reboot the system again.

Section 4. On-Line Information and Software Sources

Windows NT Automated Database: Advanced Systems at (800) 936-4400

Microsoft Software BBS: 206-936-6735 (14,400 baud)

HP Networking BBS: 208-344-1691 (14,400 baud)

HP NetServer BBS: 408-553-3500 (14,400 baud)

Section 5. HP NetServer CD Status Report

FAX

HP has a new FAX service to ensure that you have access to the newest versions of

HP NetServer system software.

To obtain an HP NetServer CD Status Report via FAX, perform the following:

1. Call the HP FIRST FAX system at 1-800-333-1917, or if you are using a

FAX machine, call 1-208-344-4809.

2. Enter the four-digit Document ID Number (printed on the NetServer

Manager CD) when prompted. The HP NetServer CD Status Report will be

faxed to you.

Internet (World-Wide)

To obtain an HP NetServer CD Status Report via Internet, locate the four-digit

Document ID Number printed on the NetServer Manager CD and do the following:

If You Have Access to the World-Wide Web:

1. Access URL http://www.hp.com/go/netserver/

2. Click on the line that corresponds to your Documentation ID Number.

If You Don't Have Access to the World-Wide Web:

1. Access the FTP server: ftp.netserver.hp.com (IP address 192.6.7.15)

LOGON: anonymous, PASSWORD: <your e-mail address>

2. Change the directory to "cd_revs" by typing: cd cd_revs

3. Get the .TXT file that corresponds to your four digit Documentation ID

Number by typing: get xxxx.txt (where xxxx is the Document ID Number)

Section 6. HP Information Assistant

Please see the CD-ROM-based HP Information Assistant for additional detailed

information to help you install your NOS.

Andere Handbücher für D6030A - NetServer - E50

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP Compaq Presario Technisches Datenblatt

HP Pavilion u501cl Bedienungsanleitung

HP Presario SR1200 - Desktop PC Bedienungsanleitung

HP Kayak XW U3-W3 Handbuch

HP Compaq 18 All-in-One Montageanleitung

HP Pavilion x360 m1-u100 Handbuch

HP dx7300 - Microtower PC Installationsanleitung

HP ZBook 14u G4 Handbuch

HP EliteDesk 705 G4 Montageanleitung

HP 705 Bedienungsanleitung

HP dc7900 - Convertible Minitower PC Bedienungsanleitung

HP A1210n - Pavilion - 512 MB RAM Bedienungsanleitung

HP ProDesk 600 G5 PCI MT Handbuch

HP dc7700 - Convertible Minitower PC Kurzanleitung

HP X Class 500/550MHz Bedienungsanleitung

HP 260 G1 Handbuch

HP Xw4300 - Workstation - 2 GB RAM Gebrauchs- und Pflegehandbuch

HP Net PC 20 Bedienungsanleitung

HP xw8600 - Workstation Bedienungsanleitung

HP Pavilion Slimline s5-1100 Anleitung zur Verwendung

HP Visualize j6000 Bedienungsanleitung

HP Compaq Presario Handbuch

HP Brio BA300 Installations- und Betriebshandbuch

HP Model 747i - Workstation Referenzhandbuch

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung

Parker

Parker PA Series Bedienungsanleitung