HP D7171A - NetServer - LPr Referenzhandbuch

HP Server

SCO UnixWare Installation Guide

NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version

M.04.05. If you don't have the M.04.05 version CD-ROM and you're obtaining this document from the HP web

site as a reference to install an operating system, be sure to also check the HP web site for the latest available

drivers.

©Copyright Hewlett-Packard Company

January 22, 2002

Introduction

This document presents important information that you need to install SCO UnixWare.

The first section of this document is a list of helpful tips on NOS installation, the second

section is a step-by-step installation guide.

NOTE: The SCO UnixWare 2.1 and UnixWare 7. X operating system is

supported on the HP NetServer LC II, LC 3, LD Pro, LH Plus, LH Pro, LH II, LH

3, LH4, LX Pro, LXe Pro, LXr Pro product families.

The SCO UnixWare 7.X operating system is supported on the HP NetServer LPr

LC2000, LH3000, LH6000, LT6000r, LXr8000, and LXr8500 product families.

The SCO UnixWare 2.1, UnixWare 7.X operating system is not supported on the

HP NetServer E 30, E 40, E 45, E 50, E 60, LC, LC Plus, LE, LF, LH, LM, and

LS product families.

The SCO UnixWare 7.1.1 operating system is not supported on the HP Server

tc3100 and tc4100 product families.

Hewlett-Packard has more than one Disk Array Controller (DAC) for the

NetServer product family. In this document the term "HP Disk Array" refers to

the EISA and PCI Disk Array Controller models C3609A and C3610A,

respectively. The term "HP NetRAID" refers to the HP NetRAID and NetRAID-

1 PCI DAC models D4943A and D4992A, The term "HP NetRAID 3Si" refers to

model number D5955A. The term "HP NetRAID 1Si refers to model number

D2140A. The term"HP Embedded RAID" refers to the built in RAID controller

on the HP NetServer LH3, LH4, LH3000, LH6000 and LT6000r.

The HP NetRAID disk array controllers will be supported on UnixWare 2.1 and

UnixWare 7.X on a future HP NetServer Navigator release.

Table of Contents

Section 1. General Tips

Introduction

CaSe SeNsItIvE

Start Counting At Zero

Set Up All Cards In ECU

Installation To Disk Arrays

Utility Partition Access Disabled

Installation Media

Swap Space

Additional File Systems

Configuring Mouse Connectors

Configuring Video for UnixWare

Host Bus Adapter (HBA) Driver Tips

Driver Names for HP-Supplied Controllers

Troubleshooting

Section 2. Installing SCO UnixWare 2.1.x

Large Memory Access

SCSI Extended Translation Setting

MPS Table Setting On NetServer LS and LX for UnixWare

HP Bundled NICs Not Supported On UnixWare 2.1.x

Installing SCO UnixWare 2.1.x

Section 3. Installing SCO UnixWare 7.1.x

Section 4. On-Line Information and Software Sources

Section 1. General Tips

Introduction

The following subsections discuss problems that you may encounter when installing SCO

UnixWare 2.1.x.

SCO UnixWare installation procedures include installing SCO UNIX files, loading all

required drivers (including HBA packages), and linking information to the kernel.

As a rule, select fully configurable, rather than automatic, initialization.

CaSe SeNsItIvE

All versions of UNIX are very case sensitive and you need to be absolutely sure that you

type in the commands exactly as instructed. Almost all UNIX commands are in lower

case so if you are unsure try lower case first.

Start Counting At Zero

In almost all cases a UNIX system will start counting at ZERO. Therefore, SCSI

Controller 0 is the first controller, SCSI Channel 0 is the first channel, Hard Disk 0 is the

first hard disk, etc.

Set Up All Cards In ECU

SCO UNIX likes to have all cards and disk drives configured in CMOS to work properly.

SCO can actually read the EISA ROM information. This means that before you try to

configure SCO to use a particular adapter card in the system go in and make sure that it is

set up in the ECU. Even if it is an ISA adapter without a config file go into the ECU and

add a "Generic ISA Adapter" and assign the appropriate resources such as DMA,

Memory, and IRQ to match the settings of the card. (There is a config file for a Generic

ISA Adapter on the NS#2 diskette or Navigator CD-ROM. Add it as a non-HP board).

Installation To Disk Arrays

Installation to a logical drive, on a disk array, larger than 2048 MB is not recommended.

For backwards compatibility and ease of system administration logical drives smaller

than 2 GB are recommended for your root drive.

Utility Partition Access Disabled

During SCO UnixWare installation, access to the Utility Partition built by the

Configuration Assistant is disabled. Select "Skip" when Configuration Assistant asks

you to build the Utility Partition.

Installation Media

The following installation media is required in addition to the main product CD-ROM or

tape to install SCO UnixWare.

For UnixWare 2.1.x: Installation diskette, SCO UnixWare Host Bus Adapter Drivers

diskette, and the HP Drivers diskette (produced from the HP NetServer Navigator CD).

Swap Space

You may wish to increase the swap space from the default provided. UnixWare uses the

swap space to swap the least-recently used pages in and out of memory. If you have the

disk space available, you might consider using more than the default, or doubling the size

of the physical memory, whichever is greater.

Additional File Systems

When installing UnixWare you have the opportunity to create separate file systems in

addition to the root file system. If you choose to create additional file systems you will be

asked to allocate disk space between your root and your other file systems. Be sure to

leave enough space in your root file system for installing future applications.

Configuring a Mouse

All HP NetServers have a PS/2 style mouse. This is also know as a mini-DIN or

keyboard mouse.

Configuring Video for UnixWare

When configuring the video for UnixWare, standard VGA is the safest choice. You can

enter the correct video driver after the system is up and running. The following video

chips are used in the HP NetServers:

E 30: S3 Trio 64V+, 1MB or 2MB video memory

E 40, LC II, LC 3, LPr, LH 3, LH4, LXr8000, and LXr8500 : Cirrus Logic CL-GD5446,

1MB or 2MB video memory

E 45: Cirrus Logic CL-GD5446, 2MB video memory

LC Plus, LD Pro, LH, LH Plus, LH Pro, and LH II: Trident TVGA9000I, 512KB video

memory

LS, LX Pro, LXe Pro, LXr Pro: Cirrus Logic CL-GD5424, 512KB or 1MB video

memory

LC2000, LH3000, LH6000, LT6000r : ATI Rage II C ,1MB or 2MB video memory

The wrong video driver can produce blank or unreadable screen displays at the higher

(greater than 640 x 480 VGA) resolutions.

Host Bus Adapter (HBA) Driver Tips

The HP NetServers use the Host Bus Adapter drivers for the internal SCSI controllers.

The HBA driver is a driver that can be link-edited into the system kernel during the

booting process. The link-editing is done by the system after the driver is loaded into

memory, but before the kernel is started

For UnixWare 2.1.x, the SCSI controller drivers are built into the SCO product. HP

recommends that you use the latest adsa and adsl drivers that SCO ships. These drivers

are available from SCO on their Host Bus Adapter Drivers disk. HP ships the SCO

PTF3124C version of the adsl driver on the driver diskette that is created by the HP

NetServer Navigator CD.

Driver Names for HP-Supplied Controllers

The following table lists the names of required drivers for the HP-supplied controllers.

NetServer Controller Package Name

E 30,40,45 AHA2910 adsl

LC Plus AIC7770 adsa

LC II,3 AIC7880 adsl

LD Pro AIC7880 adsl

LH AIC7855 adsl

LH Plus, LH Pro AIC7880 adsl

LH II,3 AIC7880 adsl

LS AIC7870 adsl

LX, LXe, LXr Pro AIC7880 adsl

LPr Symbios895 c8xx

LH3,LH4, Symbios895 c8xx

NetRaid 3Si mega

LC 2000 Symbios895 slha & mega

LH 3000 Symbios896 slha & mega

LH 6000 Symbios896 slha & mega

LT 6000r Symbios896 slha & mega

NOTE: HP currently does not support ultra SCSI mode on the AIC7880

controllers when they are connected to the HP Storage System 6. Ultra SCSI

mode is supported for disks installed in the HP NetServer cabinet.

Troubleshooting

SCO UnixWare is very specific about the hardware configuration it expects when

installing. The following limitations apply:

The root hard disk and the install device should both be on the primary SCSI channel.

The root hard disk must be SCSI ID 0. The first SCSI tape drive must be SCSI ID 2.

The first SCSI CD-ROM drive must be SCSI ID 5.

The correct SCSI ID is especially important if you are installing from the tape or CD-

ROM drive. If you have a complicated hardware configuration, install SCO

UnixWare using only the minimum system required to install. All additional

hardware can be added afterwards.

Section 2. Installing SCO UnixWare 2.1.x

Large Memory Access

SCO UnixWare 2.1.x can access a maximum of 2 GB physical memory (RAM). By

default UnixWare will not see more than 128 MB of RAM. If your system has between

128 MB and 2 GB of RAM you will need to modify the "/stand/boot" file as follows.

Add the following entry to /stand/boot:

MEMRANGE=0-640K:256,1M-16M:512,16M-nnM:8704

where "nn" is the total memory size (in MegaBytes).

See the man page for "boot" for a description of the MEMRANGE option. Edit the

/stand/boot file very carefully since an error in the file may prevent your system from

booting.

SCSI Extended Translation Setting

The SCSI extended translation setting for disks with a capacity larger than 1 GB should

be set to ‘disabled’ for all versions of SCO UnixWare. (Run the EISA Configuration

Utility or the SCSI BIOS <cntl>-A to set this parameter.)

MPS Table Setting On NetServer LS and LX for SCO MPX

For the HP NetServer LS and LX with multiprocessors, you must set the MPS

configuration parameter to the correct MPS Table setting.

1. Run the EISA Configuration Utility.

2. Move to the MPS Table selection.

3. Select the MPS table value 1.1 for SCO UnixWare 2.0x. Select MPS table value 1.4

for SCO UnixWare 2.1.x.

HP Bundled NICs Not Supported On UnixWare 2.1.x

The Network Interface Cards (NICs) that are bundled in some HP NetServer models do

not have drivers for UnixWare 2.1.x at this time. Consult SCO's hardware compatability

guide for a supported NIC.

Installing SCO UnixWare 2.1.x

The following instructions help you to install SCO UnixWare 2.1.x on your HP

NetServer system.

NOTE: In general, UnixWare can not share IRQs across different types of

controller cards.

For UnixWare 2.1.x, the SCSI controller drivers are built into the SCO product. HP

recommends that you use the latest adsl driver that SCO ships. This driver is available

from SCO on their SLS “PTF3124C”. The PTF3124C version of the adsl driver was

released after the UnixWare 2.1.x update release. HP ships the SCO PTF3124C version

of the adsl driver on the driver diskette that is created by the HP NetServer Navigator

CD.

1. Use the HP Navigator CD-ROM installation utility to configure your system

hardware. This utility creates the HP NetServer UnixWare 2.1.x Drivers diskette (the

"Drivers Diskette").

2. UnixWare 2.1.0 and 2.1.1 have problems with system memory sizes greater than 1

GB. You may experience problem loading HBA drivers during the installation

process. You may also have problems reading and writing floppy diskettes. These

problems have been resolved in UnixWare 2.1.2. HP recommends that you only use

UnixWare 2.1.2 for systems with greater than 1 GB of system memory.

3. Insert the SCO UnixWare Installation diskette and turn on your NetServer.

4. When you are asked to insert HBA driver diskettes you should first use the HP

NetServer UnixWare 2.1.x Drivers diskette and then use the SCO UnixWare Host

Bus Adapter Drivers diskette. Later during the installation you will need to reinsert

the HBA driver diskettes. The HP UnixWare 2.1.x Drivers diskette will be asked for

as the “HP NetServer UnixWare 2.1.x Drivers” diskette.

For LCII, use the latest SLS "PTF3254s" when you install the osmp package:

· Do not select the osmp package when installing UnixWare 2.1.x.

· When you finish installing UnixWare 2.1.x, then install osmp (choose Intel for

plattform). Do not reboot the machine.

· Install PTF3254s, and manually relink the kernel: # /etc/conf/bin/idbuild -B

· Reboot the machine.

5. Follow the instructions in the SCO UnixWare Installation Handbook to complete

your system installation.

6. After the installation, update your system to UnixWare 2.1.2 (or later).

For more reliable network operation, HP recommends that you install PTF3280. For

more detail on how to install PTF3280, please refer to SCO documentation. To

improve the performance of the network, you need to modify the kernel parameters:

Go into System_Tuner (in Admin_Tools folder) and modify these parameters:

For STREAMS parameters:

- Set STRMSGSZ to 0.

- Set STRSCHED to 32

For Virtual Memory (VM) parameters:

- Set MINFREEBYTE to 1048576.

- Set SEGKMEM_PERCENT to 65.

- Set SEGKMEM_BYTE to 0x7000000

Click OK, and relink the kernel. Reboot the machine.

Section 3. Installing UnixWare 7.1.x

The following instructions will help you to install SCO UnixWare 7.1.x on your HP

NetServer system.

NOTE: In general, UnixWare can not share IRQs across different types of

controller cards.

NOTE: For LP2000r, IRQ 15 cannot be assigned to any PCI Devices. IRQs must

be locked in the BIOS settings.

Steps to lock IRQs for other PCI Devices:

1. Press “F2” key during system boot up to enter the BIOS Setup Menu.

2. Wait until system enters BIOS Setup Menu.

3. Select “Configuration” from Menu and arrow down to “PCI Slot Devices” &

press Enter.

4. Arrow down to “PCI IRQ Locking” and press Enter.

5. You will see a list of your PCI Devices.

6. Arrow up and down to choose desired PCI Devices and press Enter.

7. Choose the desired available IRQ for your PCI Device other than IRQ 15.

For UnixWare 7.1.x, the SCSI controller drivers are built into the SCO product. HP

recommends that you use the HBA driver that SCO ships.

1. Use the HP Navigator CD-ROM installation utility to configure your system

hardware. This utility creates the HP NetServer UnixWare 7.1.x Drivers diskette for

HP NetRaid, latest HBA Drivers and HP nic driver.

2. Insert the SCO UnixWare Installation diskette and turn on your NetServer.

3. When you are asked to insert HBA driver diskettes you should first use the HP

NetServer UnixWare 7.1.x Drivers diskette and then use the SCO UnixWare Host

Bus Adapter Drivers diskette. Later during the installation you will need to reinsert

the HBA driver diskettes. The HP UnixWare 7.1.x Drivers diskette will be asked for

as the “HP NetServer UnixWare 7.1.x Drivers” diskette.

4. On systems with multiple host adapters installed (e.g., SymBIOS, Adaptec, and HP

NetRAID SCSI adapter card) there is a special procedure required to tell

UnixWare7.1.x which controller is number 0 (the boot controller).

· Enter into DCU.

· Select the Software Devices Configurations.

· Select the Host Bus Adapters.

· Deselect the driver for any controller in the system that is not the one you are

installing to

- Select Misc, then deselect i2otrans if present, this can cause conflict wilth

the HP NetRAID card.

- Return to DCU main menu and Save @ Exit.

5. Follow the instructions in the SCO UnixWare Installation Handbook to complete

your system installation.

Section 4. On-Line Information and Software Sources

SCO World-Wide Web Access: http://www.sco.com

SCO Anonymous FTP: ftp.sco.com

HP Internet (World-Wide-Web) site: http://www.hp.com

HP Server Online Documentation CD (included with your system): includes all HP

Server documentation online

Andere Handbücher für D7171A - NetServer - LPr

117

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP Vectra XE310 Installations- und Betriebshandbuch

HP Pavilion t600 - Desktop PC Bedienungsanleitung

HP Stream x360 Handbuch

HP 260 G3 Desktop Mini Business Handbuch

HP Pavilion a200 - Desktop PC Montageanleitung

HP M8200n - Pavilion Media Center Technisches Datenblatt

HP CQ2800 Bedienungsanleitung

HP Media Center Bedienungsanleitung

HP Pavilion Slimline s5710f Bedienungsanleitung

HP A6119h - Pavilion - 2 GB RAM Technisches Datenblatt

HP Brio 81XX Bedienungsanleitung

HP Pavilion a100 - Desktop PC Bedienungsanleitung

HP 8100 - Elite Convertible Minitower PC Gebrauchsanweisung

HP P Class 450/500/550/600/650/700/750 Bedienungsanleitung

HP Pro 6000 Montageanleitung

HP ENVY Recline 27-k050xt TouchSmart Bedienungsanleitung

HP Compaq 6005 Pro MT Bedienungs- und Wartungshandbuch

HP Pavilion u501cl Bedienungsanleitung

HP ProDesk 600 G4 Montageanleitung

HP EG652AA Bedienungsanleitung

HP Vectra VLi 8 Produkthandbuch

HP Compaq Presario Handbuch

HP B132L+ Bedienungsanleitung

HP Z1 Montageanleitung

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung