HP Kayak XA 05xx Bedienungsanleitung

HP Kayak XA- 05xx PC Workstation—

Configuring a SCSI Accessory

ash-scsi.fm Page 1 Friday, February 26, 1999 11:25 AM

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

2English

Using the SCSI Configuration Utility (Selected Models)

The Symbios Logic SCSI Configuration Utility lets you view and change

the default configuration for your host adapter and all SCSI devices

connected to it, or for individual SCSI devices.

Default Settings You Can Change

The following two tables show the configuration settings you can

change. The first table shows the global settings which impact your

host adapter and all SCSI devices connected to it. Be very careful if you

change any of these settings. The second table shows the device

settings which apply to individual devices.

Settings for the Host Adapter and All

Devices Default Settings

SCAM Support On

Parity Enabled

Host Adapter SCSI ID 7

Scan Order Low to High (0-Max)

Removable Media support None

Settings for Individual SCSI Devices Default Settings

Synchronous Transfer Rate (MB/sec) 40

Data Width 16

Disconnect On

Read Write I/O Timeout (secs) 10

Scan for Devices at Boot Time Yes

Scan for SCSI LUNs Yes

Queue Tags Enabled

ash-scsi.fm Page 2 Friday, February 26, 1999 11:25 AM

English 3

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

Starting the SCSI Configuration Utility

You access the SCSI Configuration Utility by pressing when the

message Press F6 to start Configuration Utility... is

displayed during the PC Workstation’s start-up routine. A further

message is then displayed: Please wait, invoking Configuration

Utility... before the Main menu of the Symbios Logic SCSI

Configuration utility appears.

Main Menu

NOTE The items shown on your screen may be different from those shown

below.

Use the and keys and the key to make a selection

from this menu.

You can only select an adapter if the current status is “On”. Changes

are possible only if NVRAM (non-volatile memory on your adapter) is

present.

Symbios Logic SCSI Configuration Utility

Version 1.07

MAIN MENU

Port Irq ------Status------ NvRAM

Num Level Current Next-Boot Found

.SYM53C875 E800 3 On On Yes

Change Adapter Status.

Adapter Boot Order1.

Additional Adapter Configuration1.

Display Mode = Verbose.

Mono/Color.

Language2.

Help.

Quit.

Use arrow keys to select from menu. Then press ENTER

BIOS Code Segment: C800

1. Only used if more than one Symbios card is installed.

2. Not available (English only).

ash-scsi.fm Page 3 Friday, February 26, 1999 11:25 AM

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

4English

Adapter Boot Order This option is only available when you have more than one host adapter

installed. It lets you set the order in which host adapters boot. When you

select this option the Boot Order menu is displayed.

To change an adapter’s boot order (from the Boot Order menu), select

it and press . You are then prompted to enter the new boot

sequence number. When you are satisfied with the boot order, press

to exit this menu.

Change Adapter Status This option lets you activate or deactivate a host adapter and all SCSI

devices attached to it. The change takes place after a reboot, which is

automatic when you exit from the Configuration utility after using this

option to make a change. When you select this option the Change Status

on Next Boot menu is displayed.

To toggle an adapter’s status ‘on’ or ‘off’ (from the Change Status on

Next Boot menu), select it and press . When you are satisfied

with your selections, press to exit this menu.

Display Mode This option determines how much information about your host

adapter(s) and SCSI devices is displayed on the screen during the PC

Workstation’s start-up routine. For more complete information, select

the verbose setting; for a faster boot, select the terse setting.

Mono/Color This option lets you choose between a black and white or a color display

for the SCSI configuration utility. If you are using a black and white

monitor, you may need to select the mono setting to get a more readable

screen.

Help This option displays a help screen giving information about the Main

menu.

Quit This option exits the SCSI Configuration utility.

ash-scsi.fm Page 4 Friday, February 26, 1999 11:25 AM

English 5

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

Adapter Utilities Menu

When you select (click on and press ) a host adapter from the

Main menu, the Utilities menu is displayed:

Adapter Setup This option lets you view and change the selected adapter settings.

Device Selections This option lets you view and change settings for the devices attached

to the selected adapter.

After you have made changes to the configuration of a host adapter or

to any connected SCSI device, you will return to this menu.

Symbios Logic SCSI Configuration Utility

Version 1.07

1. SYM53C875

Utilities

Adapter Setup

Device Selections

Help.

Exit this menu

Use arrow keys to select from menu. Then press ENTER

BIOS Code Segment: C800

ash-scsi.fm Page 5 Friday, February 26, 1999 11:25 AM

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

6English

Adapter Setup Menu

When you select Adapter Setup from the Adapter Utilities menu, the

Adapter Setup menu is displayed:

The settings in this menu are global settings that effect the selected

host adapter and all SCSI devices attached to it.

SCAM Support The Symbios Logic BIOS version 4.x and above supports the SCSI Plug

and Play protocol called SCAM (SCSI Configured AutoMatically). You

can turn this off if you wish.

Parity Symbios Logic PCI to SCSI host adapters always generate parity, but

some SCSI devices do not. For this reason you can disable parity

checking.

NOTE When disabling parity checking, you may have to disable disconnects for

certain devices as parity checking for the re-selection phase is not

disabled. If a device does not generate parity, and it disconnects, the I/O

never completes because the re-selection never completes.

Symbios Logic SCSI Configuration Utility

Version 1.07

1. SYM53C875

Adapter Setup

SCAM Support On

Parity Enabled

Host SCSI ID 7

Scan Order Low to High (0..Max)

Removable Media Support

CHS Mapping

Help.

Restore Default Setup.

Exit this menu.

Use arrow keys to select from menu. Then press ENTER

BIOS Code Segment: C800

ash-scsi.fm Page 6 Friday, February 26, 1999 11:25 AM

English 7

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

Host SCSI ID In general it is not advisable to change your host adapter ID from the

default value of 7, as this gives it the highest priority on the SCSI bus.

However, if you have two adapters sharing the same SCSI devices, you

should give one of the adapters a currently-unassigned ID to avoid

duplication of SCSI IDs.

Scan Order This option lets you tell the host adapter BIOS and your device drivers

to scan the SCSI bus from low to high (0 to max) SCSI ID, or from high

to low (max to 0) SCSI ID. If you have more than one device on a SCSI

bus, changing the device order changes the drive letters which are

assigned to them by the system.This will change the boot order.

Removable Media

Support

Only used when removable disk drives are installed. For more

information, refer to the User’s Guide that came with you removable

disk drive.

CHS Mapping When performing a ‘low format’, CHS mapping should be set to

Alternate CHS Mapping for full compatibility with other SCSI

adapters. This is the default setting.

ash-scsi.fm Page 7 Friday, February 26, 1999 11:25 AM

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

8English

Device Selections Menu

When you select Device Selections from the Adapter Utilities menu,

the Device Selections menu is displayed:

This menu provides information about individual SCSI devices attached

to the selected host adapter, and the adapter itself.

To make changes to these settings, select a device from the list and

press to display the individual Device Setup menu.

Symbios Logic SCSI Configuration Utility

Version 1.07

1. SYM53C875

Device Selections 0-7

Sync Data Disc Time Scan Scan Queue

Rate Width Out Bus LUNS Tags

Dev0 N/A 40 16 On 10 Yes Yes Enabled

Dev1 N/A 40 16 On 10 Yes Yes Enabled

Dev2 N/A 40 16 On 10 Yes Yes Enabled

Dev3 N/A 40 16 On 10 Yes Yes Enabled

Dev4 N/A 40 16 On 10 Yes Yes Enabled

Dev5 N/A 40 16 On 10 Yes Yes Enabled

Dev6 N/A 40 16 On 10 Yes Yes Enabled

SYM53C875 40 16 On 10 Yes Yes Enabled

Device Selections 8-15

Help.

Exit this menu.

Use arrow keys to select from menu. Then press ENTER

BIOS Code Segment: C800

ash-scsi.fm Page 8 Friday, February 26, 1999 11:25 AM

English 9

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

Device Setup Menu

When you select a device from the Device Selections menu, the Device

Setup menu is displayed:

This menu provides information about an individual SCSI device.

To make changes to these settings, select an item from the list and

press .

Sync Rate (Mega

Bytes/sec)

This option lets you set the transfer rate for the device. The available

choices are Off, 10 MB/sec, 20 MB/sec, or 40 MB/sec. For example, for a

Fast SCSI device, you would select 10 MB/sec.

Width (bits) This option lets you set the width, in bits, for the device. The choices are

8 or 16. For example, if the device is an external SCSI device, you would

set the width to 8 bits.

Disconnect This option lets you enable or disable disconnects for the device.

Read Write I/O Timeout

(sec)

This option lets you enter a read write timeout value in seconds for the

device.

Symbios Logic SCSI Configuration Utility

Version 1.00

1. SYM53C875

Dev0 N/A Setup

Sync Rate (Mega Bytes/sec) 40 MB/sec

Width (bits) 16

Disconnect On

Read Write I/O Timeout (secs) 10

Scan for Device at Boot Time Yes

Scan for SCSI LUNS Yes

Queue Tags Enabled

Format None

Verify

Help.

Restore Default Setup

Exit this menu.

Use arrow keys to select from menu. Then press ENTER

BIOS Code Segment: C800

ash-scsi.fm Page 9 Friday, February 26, 1999 11:25 AM

HP Kayak XA- 05xx PC Workstation — Configuring a SCSI Accessory

Using the SCSI Configuration Utility (Selected Models)

10 English

Scan for Device at Boot

Time

This option lets you specify whether the device is scanned for at boot

time. The choices are Yes or No.

Scan for SCSI LUNS More advanced SCSI devices can have several logical units (LUNs). This

option lets you specify whether SCSI LUNs are scanned for at boot time.

The choices are Yes or No.

Queue Tags This option lets you specify whether queue tags are enabled or disabled.

In a multi-tasking environment this option must be enabled. It should

only be disabled for troubleshooting.

Format Disk This utility can be used to perform a low-level format of a hard disk.

Most SCSI disks are pre-formatted and do not need low-level formatting.

Verify Disk Media This utility scans for media defects on the selected SCSI device. Press

the key to abort this utility.

Exiting from the Configuration Utility

To exit from the Configuration utility, press the necessary number

of times to return to the Main menu, and then press to quit.

ash-scsi.fm Page 10 Friday, February 26, 1999 11:25 AM

Andere Handbücher für Kayak XA 05xx

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP Compaq dc5100 Series Montageanleitung

HP Z200 - Small Form Factor Workstation Bedienungsanleitung

HP Pavilion a700 - Desktop PC Bedienungsanleitung

HP Pavilion t600 - Desktop PC Bedienungsanleitung

HP ProOne 600 G3 21 inch All-in-One Business PC Bedienungs- und Wartungshandbuch

HP Presario SG3500 - Desktop PC Anleitung zur Verwendung

HP Compaq Presario Handbuch

HP Compaq 8200 Bedienungsanleitung

HP Compaq Presario Technisches Datenblatt

HP Workstation xw8000 Stücklistenhandbuch

HP Pavilion t372k Bedienungsanleitung

HP m9160f - Pavilion - Elite Bedienungsanleitung

HP Pavilion 13 x2 Handbuch

HP Visualize c160 Handbuch

HP Rp3000 - Point of Sale System Bedienungs- und Wartungshandbuch

HP Vectra VL5 4 Handbuch

HP Xw6400 - Workstation - 4 GB RAM Gebrauchsanweisung

HP Vectra VL 6/xxx - 6 Bedienungsanleitung

HP Compaq Pro 6300 All-in-One Gebrauchsanweisung

HP EliteDesk 800 Bedienungs- und Wartungshandbuch

HP Media Center m7100 - Desktop PC Technisches Datenblatt

HP A6300f - Pavilion - 2 GB RAM Technisches Datenblatt

HP Compaq Presario Montageanleitung

HP EliteOne 800 G3 Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung

Parker

Parker PA Series Bedienungsanleitung