HP Kayak XU 04xx Bedienungsanleitung

SCSIAdministrator’s

Guide

HP Kayak PC

Workstations

HP Kayak PC

Workstations

SCSI Administrator’s

Guide

cognac.bk : cover.fb4 Page 1 Monday, August 17, 1998 3:48 PM

Notice

The information contained in this document is subject to change without

notice.

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose. Hewlett-Packard shall not be liable for errors

containedhereinorforincidentalorconsequentialdamagesinconnectionwith

the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

Thisdocumentcontainsproprietaryinformationthatisprotectedbycopyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written

consent of Hewlett-Packard Company.

Adaptec® is a registered trademark of Adaptec, Inc. RAIDportTM,

ArrayConfigTM, AROTM, CI/OTM andArray1000 are trademarks of Adaptec,

Inc.

Symbios LogicTM is a trademark of Symbios Logic, Inc.

Microsoft®, MS®, MS-DOS®, Windows®, and Windows NT® are U.S.

registered trademark of Microsoft Corporation.

Netscape® is a trademark of Netscape Communications Corporation.

PentiumTM is a trademark of Intel Corporation.

SCSISelectTM is a trademark of Adaptec Incorporated.

Hewlett-Packard France

Performance Desktop Computing Operation

38053 Grenoble Cedex 9

France 1998 Hewlett-Packard Company

cognac.bk : notice.fb4 Page ii Monday, August 17, 1998 3:48 PM

SCSI Administrator’s Guide

cognac.bk : title.fb4 Page iii Monday, August 17, 1998 3:48 PM

iv English

Who This Manual Is For

This manual is for anyone who wants to:

•Add a SCSI accessory to their PC Workstation.

•Configure a SCSI accessory in an HP PC Workstation.

Important Safety Information

WARNING If you have any doubt that you can lift the PC Workstation or display

safely, do not try to move it without help.

For your safety, always connect the equipment to a grounded wall

outlet. Always use a power cord with a properly grounded plug, such

as the one provided with this equipment, or one in compliance with

your national regulations. This PC Workstation is disconnected from

the power by removing the power cord from the power outlet. This

meansthePCWorkstationmustbelocatedclosetoapoweroutletthat

is easily accessible.

Foryoursafety,never remove thePCWorkstation’s cover without first

removingthepowercordfromthepoweroutlet,andanyconnectionto

a telecommunications network. Always replace the cover on the

PC Workstation before switching it on again.

To avoid electric shock, do not open the power supply. There are no

user-serviceable parts inside.

This HP PC Workstation is a class 1 laser product. Do not attempt to

make any adjustment to the laser units.

cognac.bk : title.fb4 Page iv Monday, August 17, 1998 3:48 PM

Contents

English v

Configuring the SCSI Bus

Using SCSI Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Configure/View Interface Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Boot Device Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

SCSI Device Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Advanced Configuration Options Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

SCSI Disk Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Using the SCSI Configuration Utility . . . . . . . . . . . . . . . . . . . . . . . . . 8

Default Settings You Can Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Starting the SCSI Configuration Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Adapter Utilities Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Device Selections Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Device Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Exiting from the Configuration Utility . . . . . . . . . . . . . . . . . . . . . . . . . . .16

cognac.bk : cognac.toc Page v Monday, August 17, 1998 3:48 PM

English 1

Configuring the SCSI Bus

You can configure a SCSI bus using either:

•SCSISelect — for use with Internal Wide 16-bit SCSI devices

& HP FastRAID (Adaptec), or

•SCSI Configuration Utility — for use with External and Internal

16/8-bit SCSI devices (Symbios).

Using SCSI Select

ATTENTION The SCSISelect™utility is intended for advanced users only.

Note that the SCSISelect option displayed on your screen may

be different to the one described here. Some options are not

displayed if the HP FastRAID option is installed.

The SCSISelect utility is accessed by pressing during the

computer’s start-up process when the message Press for

SCSISelect(TM) Utility! is displayed.

The Options menu is displayed.

SCSISelect(TM) Utility v1.xxx

Would you like to configure the host adapter, or run the

SCSI disk utilities? Select the option and press <Enter>.

Press <F5> to switch between color and monochrome modes.

Options

Configure/View Host Adapter Settings

SCSI Disk Utilities

Arrow keys to move cursor, <Enter> to select option, <Esc> to exit

cognac.bk : scsiadm.fb4 Page 1 Monday, August 17, 1998 3:48 PM

Configuring the SCSI Bus

2English

Use the and keys and the key to make selections in

the SCSISelect utility. Press at any time to return to the previous

menu.

Configure/View

InterfaceSettingsMenu It is recommended that you do not change these settings.

SCSI Channel Interface Definitions:

•Host Adapter SCSI ID

Changes the adapter SCSI ID from its default value of 7.

•SCSI Parity Checking

Enable or disable host adapter SCSI parity checking. Most currently

available SCSI devices do support SCSI parity. You should disable

SCSI Parity Checking if any of the attached SCSI devices do not

support SCSI parity.

Additional Options:

•Boot Device Options

Press to display the Boot Device Configuration menu,

described on the next page.

•SCSI Device Configuration

Press to display the SCSI Device Configuration menu.

SCSISelect(TM) Utility v1.xxx

Configuration

SCSI Bus Interface Definitions

Host Adapter SCSI ID . . . . . . . . . . . . . . 7

SCSI Parity Checking . . . . . . . . . . . . . . Enabled

Additional Options

Boot Device Options . . . . . . . . . . . . . . Press <Enter>

SCSI Device Configuration . . . . . . . . . . . Press <Enter>

Advanced Configuration Options . . . . . . . . . Press <Enter>

<F6> - Reset to Host Adapter Defaults

BIOS Information

Interrupt (IRQ) Channel . . . . . . . . . . . . . . 15

I/O Port Address . . . . . . . . . . . . . . . . . F800h

cognac.bk : scsiadm.fb4 Page 2 Monday, August 17, 1998 3:48 PM

English 3

Configuring the SCSI Bus

•Array 1000 BIOS (only if HP FastRAID is installed)

Thisoptionisenabledby default, and instructsthesystemtouse the

special BIOS for the FastRAID option.

•Advanced Configuration Options

Press to view the Advanced Configuration Options menu.

Boot Device

Configuration Menu This menu lets you configure the SCSI boot device. To find out the

SCSI ID of a specific SCSI device, you can run the SCSI Disk Utilities

(refer to page 7).

Use the and keys to move between options. Press to

display a menu with a selection of values.

•Boot SCSI ID

This parameter is the SCSI ID of the boot device. The default value

is 0.

•Boot Lun Number

More advanced SCSI devices can have several logical units. This

option indicates the logical unit (or Lun) on which to boot for the

drive chosen in the Boot SCSI ID. The default value is 0.

If HP FastRAID is not installed, use Setup to select the boot device.

Boot Device Configuration

Select SCSI peripheral from which to boot

To view peripheral by ID# select “SCSI Disk Utilities” from previous menu

Boot SCSI ID ................................................. 0

Option Listed Below Has NO EFFECT if MULTI LUN Support is Disabled

Boot LUN Number .............................................. 0

cognac.bk : scsiadm.fb4 Page 3 Monday, August 17, 1998 3:48 PM

Configuring the SCSI Bus

4English

SCSI Device

Configuration Menu This menu lets you configure parameters for each SCSI device on the

SCSI bus. To configure a specific SCSI device, you need to know which

SCSI ID it uses. To know the SCSI ID of a specific SCSI device, you can

run the SCSI Disk Utilities (refer to page 7).

Use the and keys to move between options. Press to

display a menu with a selection of values.

•Initiate Sync Negotiation

Some older SCSI-1 devices do not support synchronous negotiation.

Set Initiate Sync Negotiation to No for these devices.

•Maximum Sync Transfer Rate

If the SCSI device is an UltraWide SCSI device, you can use the

maximum value of 40.0 MB per second. For Ultra narrow SCSI or

Wide SCSI devices you can select a maximum transfer rate of 20.0

MB per second.

Certain older SCSI-1 devices do not support UltraWide SCSI (up to

40 MB per second) or Ultra narrow SCSI or Wide SCSI data transfer

rates (up to 20 MB per second). Select a Maximum Sync Transfer

Rate of 10.0 MB per second for these devices.

SCSI Device Configuration

SCSI Device ID #0 #1 #2 #3 #4 #5 #6 #7

Initiate Sync Negotiation... yes yes yes yes yes yes yes yes

Maximum Sync Transfer Rate.. 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0

Enable Disconnection........ yes yes yes yes yes yes yes yes

Initiate Wide Negotiation... yes yes yes yes yes yes yes yes

Options Listed Below Have NO EFFECT if the BIOS is Disabled

Send Start Unit Command.... no no no no no no no no

BIOS Multiple LUN Support.. no no no no no no no no

Include in BIOS Scan....... yes yes yes yes yes yes yes yes

SCSI Device ID #8 #9 #10 #11 #12 #13 #14 #15

Initiate Sync Negotiation... yes yes yes yes yes yes yes yes

Maximum Sync Transfer Rate.. 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0

Enable Disconnection........ yes yes yes yes yes yes yes yes

Initiate Wide Negotiation... yes yes yes yes yes yes yes yes

Options Listed Below Have NO EFFECT if the BIOS is Disabled

Send Start Unit Command.... no no no no no no no no

BIOS Multiple LUN Support.. no no no no no no no no

Include in BIOS Scan....... yes yes yes yes yes yes yes yes

SCSI Device Configuration

cognac.bk : scsiadm.fb4 Page 4 Monday, August 17, 1998 3:48 PM

English 5

Configuring the SCSI Bus

•Enable Disconnection

To optimize SCSI bus performance, Enable Disconnection should be

set to Yes.

•Initiate Wide Negotiation

This option determines whether the SCSI channel attempts 16-bit

data transfer instead of 8-bit data transfer.

•Send Start Unit Command

When set to Yes this option reduces the load on your computer’s

power supply by allowing the interface to power-up SCSI devices

one-at-a-time when you start your computer.

This option is not supported by some SCSI devices. Some SCSI

devices require a jumper to be changed before they can respond to

this command.

•BIOS Multiple LUN Support

More advanced SCSI devices can have several logical units (LUN).

This option determines whether booting a SCSI device that has

multipleLUNsissupported.SetthisoptiontoYes ifyourbootdevice

has multiple LUNs. It is set to no by default.

•Include in BIOS Scan

Thissetting,whenset to Yes,allowstheSCSI devicetobecontrolled

by the host adapter with this SCSI ID. When set to No, the adapter

does not control the SCSI device.

AdvancedConfiguration

Options Menu It is recommended that these settings are not changed.

Use the and keys to move between options. Press to

display a menu with a selection of values.

Advanced Configuration Options

Plug and Play Scam Support .................................... Enabled

Extended BIOS Translation for DOS Drives > 1 GByte ............ Enabled

Reset SCSI Bus at IC Initialization............................ Enabled

Options Listed Below Have NO EFFECT if the BIOS is Disabled

Host Adapter BIOS (Configuration Utility Reserves BIOS Space).. Enabled

Support Removable Disks Under BIOS as Fixed Disks.............. Boot Only

Display F6 Message During BIOS Initialization.................. Enabled

BIOS Support for Int13 Extensions.............................. Enabled

cognac.bk : scsiadm.fb4 Page 5 Monday, August 17, 1998 3:48 PM

Andere Handbücher für Kayak XU 04xx

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP Media Center Handbuch

HP Media Center m300 - Desktop PC Bedienungsanleitung

HP EliteDesk 705 G2 Desktop Mini Handbuch

HP Compaq Presario Bedienungsanleitung

HP Compaq dc5000 MT Technisches Datenblatt

HP A320m - Pavilion - 256 MB RAM Montageanleitung

HP Neoware c50 - Thin Client Benutzerhandbuch

HP Pavilion Elite E-300 - Desktop PC Bedienungsanleitung

HP Compaq Presario Handbuch

HP ZBook x2 Handbuch

HP e-PC c10/s10 Service-Handbuch

HP Compaq dc7800 Series Gebrauchsanweisung

HP Compaq Elite 8000 CMT Bedienungsanleitung

HP DY058A Bedienungsanleitung

HP TouchSmart dx9000 Bedienungsanleitung

HP ProDesk 400 G5 Montageanleitung

HP VECTRA XW Bedienungsanleitung

HP D300s - Evo - 128 MB RAM Technisches Datenblatt

HP TouchSmart 610-1200 Bedienungsanleitung

HP Workstation xw4000 Series Handbuch

HP Pavilion a1000 - Desktop PC Bedienungsanleitung

HP Z220 SFF Series Bedienungsanleitung

HP Elite 7200 - Microtower PC Bedienungsanleitung

HP T1000 Handbuch

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung

Parker

Parker PA Series Bedienungsanleitung