HP Kayak XU 04xx Bedienungsanleitung

HP Kayak XU PC Workstation

Configuring a SCSI Accessory

Cog-scsi.fm Page 1 Thursday, February 4, 1999 1:51 PM

HP Kayak XU PC Workstation Configuring a SCSI Accessory

2English

There are two ways to configure a SCSI accessory:

•SCSISelect — for use with Internal Wide 16-bit SCSI devices

& HP FastRAID (Adaptec).

•SCSI Configuration Utility — for use with External and Internal

16/8-bit SCSI devices (Symbios).

NOTE You cannot boot from a device connected to the Symbios controller

when HP FastRAID is installed.

To disable a boot device:

1Go to the Advanced menu in the Setup program.

2Select the SCSI channel you wish to set.

3Enable or disable the Option ROM Scan as required.

Using SCSI Select

ATTENTION The SCSISelect™utility is intended for advanced users only.

Note that the SCSISelect options displayed on your screen may

be different from those described here. Some options are not

displayed if the HP FastRAID option is installed.

The SCSISelect utility is accessed by pressing during the

computer’s start-up process when the message Press for

SCSISelect(TM) Utility! is displayed.

Cog-scsi.fm Page 2 Thursday, February 4, 1999 1:51 PM

English 3

HP Kayak XU PC Workstation Configuring a SCSI Accessory

The Options menu is displayed.

Use the and keys and the key to make selections in

the SCSISelect utility. Press at any time to return to the previous

menu.

Configure/View

Interface Settings Menu

It is recommended that you do not change these settings.

SCSISelect(TM) Utility v1.xxx

Would you like to configure the host adapter, or run the

SCSI disk utilities? Select the option and press <Enter>.

Press <F5> to switch between color and monochrome modes.

Options

Configure/View Host Adapter Settings

SCSI Disk Utilities

Arrow keys to move cursor, <Enter> to select option, <Esc> to exit

SCSISelect(TM) Utility v1.xxx

Configuration

SCSI Bus Interface Definitions

Host Adapter SCSI ID . . . . . . . . . . . . . . 7

SCSI Parity Checking . . . . . . . . . . . . . . Enabled

Additional Options

Boot Device Options . . . . . . . . . . . . . . Press <Enter>

SCSI Device Configuration . . . . . . . . . . . Press <Enter>

Advanced Configuration Options . . . . . . . . . Press <Enter>

<F6> - Reset to Host Adapter Defaults

BIOS Information

Interrupt (IRQ) Channel . . . . . . . . . . . . . . 15

I/O Port Address . . . . . . . . . . . . . . . . . F800h

Cog-scsi.fm Page 3 Thursday, February 4, 1999 1:51 PM

HP Kayak XU PC Workstation Configuring a SCSI Accessory

4English

SCSI Channel Interface Definitions:

•Host Adapter SCSI ID

Changes the adapter SCSI ID from its default value of 7.

•SCSI Parity Checking

Enable or disable host adapter SCSI parity checking. Most currently

available SCSI devices do support SCSI parity. You should disable

SCSI Parity Checking if any of the attached SCSI devices do not

support SCSI parity.

Additional Options:

•Boot Device Options

Press to display the Boot Device Configuration menu,

described on the next page.

•SCSI Device Configuration

Press to display the SCSI Device Configuration menu.

•Array 1000 BIOS (only if HP FastRAID is installed)

This option is enabled by default, and instructs the system to use the

special BIOS for the FastRAID option. If you disable this option and

re-boot, the system will use its normal BIOS and FastRAID will be

disabled.

•Advanced Configuration Options

Press to view the Advanced Configuration Options menu.

Cog-scsi.fm Page 4 Thursday, February 4, 1999 1:51 PM

English 5

HP Kayak XU PC Workstation Configuring a SCSI Accessory

Boot Device

Configuration Menu

This menu lets you configure the SCSI boot device. To find out the

SCSI ID of a specific SCSI device, you can run the SCSI Disk Utilities

(refer to page 8).

Use the and keys to move between options. Press to

display a menu with a selection of values.

•Boot SCSI ID

This parameter is the SCSI ID of the boot device. The default value

is 0.

•Boot Lun Number

More advanced SCSI devices can have several logical units. This

option indicates the logical unit (or Lun) on which to boot for the

drive chosen in the Boot SCSI ID. The default value is 0.

SCSI Device

Configuration Menu

This menu lets you configure parameters for each SCSI device on the

SCSI bus. To configure a specific SCSI device, you need to know which

SCSI ID it uses. To know the SCSI ID of a specific SCSI device, you can

run the SCSI Disk Utilities (refer to page 8).

Use the and keys to move between options. Press to

display a menu with a selection of values.

•Initiate Sync Negotiation

Some older SCSI-1 devices do not support synchronous negotiation.

Set Initiate Sync Negotiation to No for these devices.

Boot Device Configuration

Select SCSI peripheral from which to boot

To view peripheral by ID# select “SCSI Disk Utilities” from previous menu

Boot SCSI ID ................................................. 0

Option Listed Below Has NO EFFECT if MULTI LUN Support is Disabled

Boot LUN Number .............................................. 0

SCSI Device Configuration

SCSI Device ID #0 #1 #2 #3 #4 #5 #6 #7

Initiate Sync Negotiation... yes yes yes yes yes yes yes yes

Maximum Sync Transfer Rate.. 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0

Enable Disconnection........ yes yes yes yes yes yes yes yes

Initiate Wide Negotiation... yes yes yes yes yes yes yes yes

Options Listed Below Have NO EFFECT if the BIOS is Disabled

Send Start Unit Command.... no no no no no no no no

BIOS Multiple LUN Support.. no no no no no no no no

Include in BIOS Scan....... yes yes yes yes yes yes yes yes

Cog-scsi.fm Page 5 Thursday, February 4, 1999 1:51 PM

HP Kayak XU PC Workstation Configuring a SCSI Accessory

6English

•Maximum Sync Transfer Rate

If the SCSI device is an UltraWide SCSI device, you can use the

maximum value of 40.0 MB per second. For Ultra narrow SCSI or

Wide SCSI devices you can select a maximum transfer rate of 20.0

MB per second.

Certain older SCSI-1 devices do not support UltraWide SCSI (up to

40 MB per second) or Ultra narrow SCSI or Wide SCSI data transfer

rates (up to 20 MB per second). Select a Maximum Sync Transfer

Rate of 10.0 MB per second for these devices.

•Enable Disconnection

To optimize SCSI bus performance, Enable Disconnection should be

set to Yes.

•Initiate Wide Negotiation

This option determines whether the SCSI channel attempts 16-bit

data transfer instead of 8-bit data transfer.

•Send Start Unit Command

When set to Yes this option reduces the load on your computer’s

power supply by allowing the interface to power-up SCSI devices

one-at-a-time when you start your computer. When set to No each

SCSI device powers up at the same time.

This option is not supported by some SCSI devices. Some SCSI

devices require a jumper to be changed before they can respond to

this command.

•BIOS Multiple LUN Support

More advanced SCSI devices can have several logical units (LUN).

This option determines whether booting a SCSI device that has

multiple LUNs is supported. Set this option to Yes if your boot device

has multiple LUNs. It is set to no by default.

•Include in BIOS Scan

This setting, when set to Yes, allows the SCSI device to be controlled

by the host adapter with this SCSI ID. When set to No, the adapter

does not control the SCSI device.

Cog-scsi.fm Page 6 Thursday, February 4, 1999 1:51 PM

English 7

HP Kayak XU PC Workstation Configuring a SCSI Accessory

AdvancedConfiguration

Options Menu

It is recommended that these settings are not changed.

Use the and keys to move between options. Press to

display a menu with a selection of values.

•Plug and Play Scam Support

When enabled, this option automatically configures Plug and Play

compatible SCSI devices. For SCSI devices that do not support Plug

and Play, set this option to Disabled. By default, it is enabled.

•Extended BIOS Translation for DOS Drives >1 GByte

This option is no longer used (and must always be “Enabled”).

•Reset SCSI Bus at IC Initialization

When the SCSI controller receives an IC Reset command from the

central processor, it can reset either itself and the SCSI bus, or just

itself. By default, it will reset both itself and the SCSI bus.

•Host Adapter BIOS

This option enables or disables the SCSI Adapter BIOS. Several

options in SCSISelect utility are only valid if the SCSI adapter BIOS

is enabled. The SCSI adapter BIOS must be enabled if the computer

boots from a SCSI hard disk drive. This option is enabled by default.

•Support Removable Disks Under BIOS as Fixed Disks

When Boot Only is selected, only the removable media drive

designated as the boot device is treated as a hard disk drive.

If All Disks is selected, all removable-media drives supported by

the BIOS are treated as hard disk drives. No removable-media drives

are treated as hard disk drives when Disabled is selected. In this

case, removable-media drives must be controlled through operating

system drivers.

Advanced Configuration Options

Plug and Play Scam Support .................................... Enabled

Extended BIOS Translation for DOS Drives > 1 GByte ............ Enabled

Reset SCSI Bus at IC Initialization............................ Enabled

Options Listed Below Have NO EFFECT if the BIOS is Disabled

Host Adapter BIOS (Configuration Utility Reserves BIOS Space).. Enabled

Support Removable Disks Under BIOS as Fixed Disks.............. Boot Only

Display F6 Message During BIOS Initialization.................. Enabled

BIOS Support for Bootable CD-ROM............................... Enabled

BIOS Support for Int13 Extensions.............................. Enabled

Cog-scsi.fm Page 7 Thursday, February 4, 1999 1:51 PM

HP Kayak XU PC Workstation Configuring a SCSI Accessory

8English

•Display <F6> Message During BIOS Initialization

When enabled, this option displays the message Press <F6> for

SCSISelect(TM) Utility during BIOS initialization. When

disabled, this message is not displayed, although you can still press

the key for the SCSISelect utility. This option is enabled by

default.

•BIOS Support for Bootable CD-ROM

When enabled, this option provides BIOS support for booting from a

CD-ROM drive. It is enabled by default.

•BIOS Support for Int13 Extensions

When enabled, this option provides BIOS support for hard disk

drives with more than 1024 cylinders. It is enabled by default.

SCSI Disk Utilities When the SCSI Disk Utilities are selected from the initial Options menu,

the SCSISelect utility scans the SCSI bus and lists all the SCSI devices

on the SCSI bus. The list shows the SCSI ID and name of each SCSI

device. You can use this list to discover the SCSI ID of any device on the

SCSI bus.

Use the and keys to highlight a device and press to

display the Format Disk/Verify Media menu.

•Format Disk

This utility can be used to perform a low-level format of a hard disk.

Most SCSI disks are pre-formatted and do not need low-level

formatting. You should note that this function can take several hours.

•Verify Disk Media

This utility scans for media defects on the selected SCSI device.

Press the key to abort this utility.

Cog-scsi.fm Page 8 Thursday, February 4, 1999 1:51 PM

English 9

HP Kayak XU PC Workstation Configuring a SCSI Accessory

Using the SCSI Configuration Utility

The Symbios Logic SCSI Configuration Utility lets you view and change

the default configuration for your host adapter and all SCSI devices

connected to it, or for individual SCSI devices.

Default Settings You Can Change

The following two tables show the configuration settings you can

change. The first table shows the global settings which impact your

host adapter and all SCSI devices connected to it. Be very careful if you

change any of these settings. The second table shows the device

settings which apply to individual devices.

Settings for the Host Adapter and All Devices Default Settings

SCAM Support On

Parity Enabled

Host Adapter SCSI ID 7

Scan Order Low to High (0-Max)

Removable Media Support None

Settings for Individual SCSI Devices Default Settings

Synchronous Transfer Rate (MB/sec) 40

Data Width 16

Disconnect On

Read Write I/O Timeout (secs) 10

Scan for Devices at Boot Time Yes

Scan for SCSI LUNs Yes

Queue Tags Enabled

Cog-scsi.fm Page 9 Thursday, February 4, 1999 1:51 PM

HP Kayak XU PC Workstation Configuring a SCSI Accessory

10 English

Starting the SCSI Configuration Utility

You access the SCSI Configuration Utility by pressing when the

message Press F6 to start Configuration Utility... is

displayed during the PC Workstation’s start-up routine. A further

message is then displayed: Please wait, invoking Configuration

Utility... before the Main menu of the Symbios Logic SCSI

Configuration utility appears.

Main Menu

NOTE The items shown on your screen may be different from those shown

below.

Use the and keys and the key to make a selection

from this menu.

You can only select an adapter if the current status is “On”. Changes

are possible only if NVRAM (non-volatile memory on your adapter) is

present.

Symbios Logic SCSI Configuration Utility

Version 1.07

MAIN MENU

Port Irq ------Status------ NvRAM

Num Level Current Next-Boot Found

.SYM53C875 E800 3 On On Yes

Change Adapter Status.

Adapter Boot Order1.

Additional Adapter Configuration1.

Display Mode = Verbose.

Mono/Color.

Language2.

Help.

Quit.

Use arrow keys to select from menu. Then press ENTER

BIOS Code Segment: C800

1. Only used if more than one Symbios card is installed.

2. Not available (English only).

Cog-scsi.fm Page 10 Thursday, February 4, 1999 1:51 PM

Andere Handbücher für Kayak XU 04xx

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP DC7600 - HP Bedienungsanleitung

HP Personal Computer Technisches Datenblatt

HP ZX2000 Handbuch

HP Compaq d330 DT Bedienungsanleitung

HP Media Center Bedienungsanleitung

HP Visualize c160 Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Bedienungsanleitung

HP Z Series Handbuch

HP P Class 733/800/866MHz / 1GHz Bedienungsanleitung

HP Pavilion xg900 - Desktop PC Handbuch

HP Pavilion 9690C Bedienungsanleitung

HP Kayak XA-s 02xx Bedienungsanleitung

HP ENVY Touch 23 All-in-One Montageanleitung

HP Pavilion 400 - Desktop PC Montageanleitung

HP Workstation Z600 Bedienungsanleitung

HP Pavilion t100 - Desktop PC Handbuch

HP Digital AlphaStation 255 Family Bedienungsanleitung

HP Pavilion a210 Bedienungsanleitung

HP Omni Pro 110 Einrichtungshandbuch

HP MP9 G4 Handbuch

HP dx1000 - Microtower PC Einrichtungshandbuch

HP Z200 - Small Form Factor Workstation Bedienungsanleitung

HP Xw6600 - Workstation - 2 GB RAM Gebrauchs- und Pflegehandbuch

HP Xw6400 - Workstation - 4 GB RAM Kurzanleitung

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung

Parker

Parker PA Series Bedienungsanleitung