HP Visualize c100 Bedienungsanleitung
Installing the C100/C110/C160/C180 to C200
CPU Upgrade
PRELIMINARY 03/19/97 (includes power supply
r&r)
HP Part No. A4200-900XX
E0XXX
Printed in USA
Hewlett-Packard Co. 1997
Printing History
First Printing: January 1997
UNIX is a registered trademark in the United States and other countries,
licensed exclusively through X/Open Company Limited.
NOTICE
The information contained in this document is subject to change without
notice.
HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH
REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be lia-
ble for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copy-
right. All rights reserved. No part of this document may be photocopied,
reproduced or translated to another language without the prior written con-
sent of Hewlett-Packard Company.
RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by gov-
ernment is subject to restrictions as set forth in subdivision (c) (1) (ii) of the
Rights in Technical Data and Computer Software Clause at DFARS
252.227.7013. Hewlett-Packard Co., 3000 Hanover St., Palo Alto, CA
94304.
10 9 8 7 6 5 4 3 2 1
1
Upgrading your Model C100/C110/C160/C180 to a Model C200
Upgrading your Model C100/C110/C160/C180 to a
Model C200
Your upgrade kit contains a Power Supply and Main Tray Assembly, which,
when installed, upgrades your Model C100/C110/C160/C180 to a Model
C200.
NOTE: Installing this upgrade in your Model C100/C110/C160 or C180 does not affect the
regulatory and safety classifications or approvals. The upgraded system meets all of
the regulatory and safety standards listed in Appendix A of your original owner’s
guide.
2
Installation Prerequisites
Installation Prerequisites
Before the Model C100/C110/C160/C180 to a Model C200 Upgrade can be
performed, the current system must have an operating system version HP-
UX 10.20 or greater. The graphics card option being moved to the new
system must also be on the supported list of cards. If it is not, use the builtin
EG graphics or upgrade the graphics card option to a supported
configuration as outlined in the graphics option table below
Operating System
Verify that the HP-UX operating system is at a minimum level of 10.20. This
software must be loaded on the system before performing this upgrade.
Graphics Card Support
Verify that the graphics card(s) installed in your Model C100/C110/C160/
C180 are supported on the Model C200. The /usr/bin/graphinfo command
will display the current graphics card(s) information. Both HCRX8 and
HCRX24 cards require a physical inspection of the card to verify the Z-
Accelerator part number. The first 5 alpha-numeric characters on the Z
Accelerators white label must read A4242. The Z-Accelerator is the small
daughter card. If a graphics upgrade is required, it should be performed prior
to performing this upgrade.
The following table presents the graphics options that are supported and
NOT supported or recognized under HP-UX 10.20.
Table 1 Graphics Options Supported and Not Supported Under HP-UX 10.20
Graphic Options Supported Graphic Options NOT Supported
VIZUALIZE-8, 24, 48, 48XP Color - A4077A
VIZUALIZE EG, Dual EG Dual Color - A4078A
A4070A/B + A4242A (HCRX-8Z
with the A4443A Upgrade)
A4071A/B + A4242A (HCRX-24Z
with the A4443A Upgrade) A4071B HCRX-24 with the A4072A Z
Accelerator
3
Upgrade Instructions Overview
Upgrade Instructions Overview
The general steps for performing the upgrade are outlined as follows and
should be performed in the sequence listed. Refer to the individual sections
of this guide for the actual step-by-step procedures for upgrading the C100/
110/C160/180 to a C200.
1Update or arrange to have your operating system software updated to HP-UX
10.20. This can be a complex task and takes some time and planning.
NOTE: You must back up your system before updating your operating system.
2Determine and WRITE DOWN the LAN ID of your system. You will need to re-
enter it into the new system board
3Run the cclass_upgrade program
4Power off the workstation and any peripherals and unplug the power cords. Dis-
connect any peripheral cables and remove the floor stand
5Remove the main tray assembly
6Remove the memory boards from the CPU board and the option boards from the
main tray and reinstall them onto the new main tray
7Remove the old power supply and replace it with the new power supply.
8Place the new main tray assembly into the workstation chassis
9Connect power cords and cables, restart the workstation, and enter the LAN ID
when prompted
4
Preparing Your Workstation
Preparing Your Workstation
Before starting the upgrade, use the following procedure to prepare the
workstation:
1The workstation must be running HP-UX 10.20 or later to accommodate the
C200 upgrade. If the workstation is running a version of HP-UX lower than
10.20, update the operating system software before continuing.
NOTE: Updating the operating system takes some time to perform. Please backup your
system before updating.
2Determine the workstations LAN ID with the lanscan command by entering the
following command:
/usr/sbin/lanscan
The output is similar to the following:
Hardware Station Dev Hardware Net-Interface NM Encapsulation Mjr
Path Address lu State NameUnit State ID Methods Num
2.0.2 0x08000970ECC0 0 UP lan0 UP 4 ETHER 52
After you install the new CPU board or I/O board and power on the system for
the first time, you will be prompted for the LAN ID. Record the LAN ID here.
You will need it after installing the new system board:
EnterLAN ID ___________________-_____________________
You must supply the dash (-) between the first six digits and the last six digits.
Using the above output example, the LAN ID is 080009-70ECC0
3Logout of your system and enter a no windows command line session as follows:
HP VUE: At the login window, select Options, then select No Windows.
HP CDE: At the login window, select Option, then select
Command Line Login.
5
Preparing Your Workstation
4Next, you need to run the upgrade utility program to automatically convert the
hardware paths stored in the system’s I/O configuration file. You should only run
thisutilityifyouaregoingtocompletetherestofthehardwareupgradedescribed
in this document.
Enter the following command to run the upgrade utility program:
/usr/sam/lbin/cclass_upgrade
The upgrade utility prompts you to confirm that you want to continue, as fol-
lows:
Are you ready to perform the upgrade (y/n [n])?
Enter Y.
The upgrade utility proceeds to modify the I/O configuration information that is
stored in the files /etc/ioconfig and /stand/ioconfig to be compatible with the
upgraded system. The original I/O configuration information is saved in the
backup file /etc/ioconfig.pre_upgrade.
If the utility detects an A4077A Color Graphics Card or an A4078A Dual Color
Graphics Card in the system, it will inform you to remove them when you per-
form the hardware portion of this upgrade. Systems with built-in Enhanced
Graphics adapters do not support these optional graphics adapters.
If you have a Visualize48Z (A4444A) graphics adapter installed, the utility may
ask you to identify which slot the card set is installed in. Respond with the high-
est numbered option slot that the graphics adapter card set resides in.
NOTICE???: The cclass_upgrade utility modifies the hardware configuration so that it
is incompatible with a C100 or C110 system. After running the utility, you
must continue with this upgrade or restore the configuration information
from /etc/ioconfig.pre_upgrade to /etc/ioconfig and /stand/ioconfig.
5Power off your workstation by pressing the power button on the front panel.
When you press the power button, the workstation automatically shuts down the
operating system before it powers off the system.
6Wait for the system to completely shutdown.
7Unplug the power cord of the system unit, the monitor, and any peripheral devic-
es from ac wall outlets.
8Unplug the power cord from the back of the system unit.
6
Preparing Your Workstation
WARNING: To avoid electrical shock, make sure you unplug the power cable from
the wall outlet and the system unit before proceeding any further.
CAUTION: The internal components of your workstation are susceptible to mechanical and
electrostatic shock. To prevent such damage from occurring, observe the following
precautions during the installation procedure.
•Stand on a static-free mat (if available).
•Wearastatic-groundingwrist straptoensurethatany accumulatedelectrostatic charge
discharges from your body to ground. Attach the static-grounding wrist strap by fol-
lowing the instructions on the package that contains the strap. Be sure to attach one
end of the strap to the system chassis.
7
Preparing Your Workstation
9Remove the floor stand from the system unit, as shown in Figure 1.
Figure 1 Removing the Floor Stand
10 Lay the system unit on a flat surface, such as a table top.
11 Attach a static-grounding wrist strap to bare metal on the back of the system unit.
8
Removing the Main Tray Assembly
Removing the Main Tray Assembly
Once you have prepared the workstation, you need to remove the main tray
from the system unit, as described in the following procedure:
1Completely loosen the four thumb screws on the rear of the system unit, as shown
in Figure 2.
Figure 2 Removing Main Tray Assembly
2Place one hand on the top of the system unit and push, while pulling the handle
on the rear panel with your other hand. See Figure 2.
3Slide the main tray assembly out of the chassis.
Thumb Screws
Thumb
Screws
Andere Handbücher für Visualize c100
6
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere HP Desktop Handbücher
HP
HP Vectra VE5 2 Bedienungsanleitung
HP
HP All-in-One Montageanleitung
HP
HP Pavilion a210 Bedienungsanleitung
HP
HP m9250f - Pavilion - Elite Anleitung zur Verwendung
HP
HP Pavilion w1000 - Desktop PC Bedienungsanleitung
HP
HP Vectra VE 7 Montageanleitung
HP
HP Compaq Presario Technisches Datenblatt
HP
HP Xw4300 - Workstation - 2 GB RAM Gebrauchsanweisung
HP
HP Pavilion t272 Bedienungsanleitung
HP
HP Pavilion t300 - Desktop PC Bedienungsanleitung
HP
HP Workstation Z210 CMT Bedienungsanleitung
HP
HP dx2280 - Microtower PC Gebrauchsanweisung
HP
HP Pavilion k300 - Desktop PC Montageanleitung
HP
HP Compaq dc7900 Convertible Minitower Business Montageanleitung
HP
HP dx7300 - Microtower PC Gebrauchs- und Pflegehandbuch
HP
HP Pavilion t225d Bedienungsanleitung
HP
HP Compaq dx2818 Microtower Bedienungs- und Wartungshandbuch
HP
HP Brio 8000 Bedienungsanleitung
HP
HP Pavilion t600 - Desktop PC Bedienungsanleitung
HP
HP 286 Pro G3 Montageanleitung
