HP Z600 - Workstation - 6 GB RAM Bedienungsanleitung

Diskette drive installation

Introduction

This document describes how to install a diskette drive in an HP series Workstation.

Kit contents

●Diskette drive

●Optical bay drive carrier

●Cables

●Four M3 guide screws (for HP 400 Workstations)

Before you begin

To view QuickSpecs and determine the compatibility of this product with your HP workstation, see

http://www.hp.com/go/productbulletin.

ENWW Introduction 1

Warnings and cautions

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence

of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed

area marked with this symbol.

WARNING! To reduce the risk of electric shock or damage to your equipment:

— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence

of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce

the risk of injury from a hot component, enable the surface to cool before touching.

WARNING! If a product is shipped in packaging marked with this symbol, , the product must always

be lifted by two persons to avoid personal injury due to product weight.

WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper

workstation setup, posture, health, and work habits for computer users, and provides important electrical

and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the

documentation CD (if one is included with the product).

CAUTION: Static electricity can damage the electronic components of the workstation. Before

beginning these procedures, be sure you discharge static electricity by briefly touching a grounded metal

object.

CAUTION: To prevent damage to the workstation, observe the following Electrostatic Discharge

(ESD) precautions while performing the system parts removal and replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body

to the ground.

— Create a common ground for the equipment you are working on by connecting the static-free mat,

static strap, and peripheral units to that piece of equipment.

NOTE: HP accessories are for use in HP Workstation products. They have been extensively tested

for reliability and are manufactured to high quality standards.

2 Diskette drive installation ENWW

Step 1—Preparing for component installation

NOTE: Workstation models vary. All illustrations are examples only.

Accessing the internal components of the workstation

1. If you need help preparing the workstation for this installation, consult the removal and replacement

procedures in the service guide for your workstation at http://www.hp.com/support/

workstation_manuals.

NOTE: For the HP Workstation series, these procedures are also available in the User

Guide on the Documentation and Diagnostics CD that shipped with your workstation.

2. Power down the workstation, and then disconnect the power cord.

3. Power down all external devices, and then disconnect them from the workstation.

4. Remove the side access panel.

Removing components

1. If present, remove the airflow guide to enable access to the optical bay and system board

connectors.

2. Remove the front bezel if applicable.

NOTE: The front bezel does not need to be removed on HP 600 and HP 800 Workstations.

3. Remove the filler from the lowest available optical drive bay.

Step 2—Installing the diskette drive

1. For HP 400 Workstations, install four black M3 guide screws in the four lower holes on the carrier.

Figure 1 Installing guide screws in the carrier for HP 400 Workstations

2. To install the diskette drive in the optical bay carrier:

a. Leave the four preinstalled guide screws in the lower holes of the diskette drive in place.

b. Use the four guide screws to align the diskette drive with the carrier .

ENWW Step 1—Preparing for component installation 3

c. Lower the diskette drive into the carrier

Figure 2 Installing the diskette drive in the optical bay drive carrier

d. Align the rear screws on the drive with the channel in the carrier .

e. To fully seat the diskette drive in the carrier, the carrier cannot be in contact with a solid

surface. Lift the carrier up as you slide the drive forward .

f. The green carrier latch snaps into place when fully seated.

Figure 3 Installing the diskette drive in the optical bay drive carrier

4 Diskette drive installation ENWW

3. To install the drive carrier and diskette drive, disengage the optical bay release latch while

inserting the carrier into the optical drive bay

Figure 4 Installing the carrier in the optical bay

4. Slide the carrier into the bay. Release the latch just before the carrier is fully seated, to enable the

latch pins to engage.

Step 3—Configuring the cabling

NOTE: To locate connectors on the system board, see to the service label on the side access panel.

1. Locate the optical drive power supply cable, and then attach the end connector to the diskette drive

2. Select the diskette drive data cable that best fits the hardware configuration of the workstation, and

then connect one end to the hard drive

Figure 5 Diskette power and data connections

3. Connect the other end of the data cable to the system board.

CAUTION: The cable must stay between the system board and the hard drive cage to avoid

interfering with the heatsink fans and airflow.

ENWW Step 3—Configuring the cabling 5

4. Gently push the cable down to keep it off the system board. .

Figure 6 Routing the diskette data cable

Step 4—Reassembling the workstation

1. Reinstall the bezel, if applicable.

2. Reinstall the airflow guide, if applicable.

3. Reinstall the side access panel.

4. Reconnect power to the workstation and all external devices.

5. Restore power to the workstation and all external devices.

Japanese 日本語

This document is available in Japanese. See http://www.hp.com/support/workstation_manuals, then

select your workstation product and select Japanese from the drop down Manual Language menu.

このドキュメントは日本語版が用意されています。http://www.hp.com/support/workstation_manuals

にアクセスし、ご使用のワークステーション製品を選択し、Manual Language ドロップダウンメニ

ューから Japanese を選択してください。

6 Diskette drive installation ENWW

Andere Handbücher für Z600 - Workstation - 6 GB RAM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP TouchSmart dx9000 Bedienungsanleitung

HP BladeSystem Blade Enclosure Montageanleitung

HP Vectra XM 5/xxx - 3 Bedienungsanleitung

HP dx2420 - Microtower PC Bedienungsanleitung

HP 9050 CE Bedienungsanleitung

HP Pavillion P590-0066 Leitfaden

HP IQ815 - TouchSmart - 4 GB RAM Bedienungsanleitung

HP Visualize c100 Bedienungsanleitung

HP dx6120 - Microtower PC Bedienungs- und Wartungshandbuch

HP pavilion x360 Handbuch

HP Vectra VL 6/xxx - 6 Bedienungsanleitung

HP Compaq Presario Bedienungsanleitung

HP s3020n - Pavilion - Slimline Technisches Datenblatt

HP Pavilion t368 Bedienungsanleitung

HP Pavilion t442k Bedienungsanleitung

HP Vectra XA 6/xxx Bedienungsanleitung

HP ProDesk 600 Handbuch

HP s3600f - Pavilion - Slimline Gebrauchs- und Wartungshandbuch

HP Kayak XW U3-W3 Stücklistenhandbuch

HP Presario SG3000 - Desktop PC Bedienungsanleitung

HP Xw9300 - Workstation - 1 GB RAM Gebrauchs- und Pflegehandbuch

HP Compaq Presario Bedienungsanleitung

HP Compaq Presario Handbuch

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung

Parker

Parker PA Series Bedienungsanleitung