HP 100B-TX Bedienungsanleitung

Intel EtherExpress PRO 100B-TX

PCI Ethernet Adapter

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter

Microsoft Windows 95 SR2.5

1 Installing the Intel EtherExpress PRO 100B-TX PCI

Ethernet Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 3.51 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT Server 3.51 system that supports NetBEUI, TCP/

IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-

TX PCI adapter card into an PCI slot.

2Connect network cable media to the PRO 100B-TX PCI card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and

execute “A:\SETUP.EXE”.

5Select “VIEW ADAPTER SETTINGS” and verify the resource settings

listed above under the heading “Device Configuration”.

6If changes are required, save those changes and exit.

7Remove the Intel Software driver diskette and restart the system.

8When Windows 95 restarts, a message will appear to indicate that a new

hardware has been found.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 10 03 10

I/O Address 1020 DCE0 E400

1 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter

Connecting to a Windows NT 3.51 Server

9When prompted, click on “Next” and then click on “Other Locations” to

provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.

10 Insert the drivers diskette and set the path statement to “A:\” and click on

“OK”.

11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on

“Finish”.

12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and

click on “OK”.

13 Click “OK” to the “Network dialog box to provide computer / workgroup

names.

14 Specify your Computer Name, Workgroup, and Computer Description. (If

you do not have the required information, contact your network

administrator).

15 Click on “Close” button, and files will copy.

16 Click on the “Yes” button to finish the installation and restart your

computer.

2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter

Microsoft Windows 95 SR2.5

2 Installing the Intel EtherExpress PRO 100B-TX PCI

Ethernet Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 4.0 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT Server 4.0 system that supports NetBEUI, TCP/IP,

NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-

TX PCI adapter card into an PCI slot.

2Connect network cable media to the PRO 100B-TX PCI card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and

execute “A:\SETUP.EXE”.

5Select “VIEW ADAPTER SETTINGS” and verify the resource settings

listed above under the heading “Device Configuration”.

6If changes are required, save those changes and exit.

7Remove the Intel Software driver diskette and restart the system.

8When Windows 95 restarts, a message will appear to indicate that a new

hardware has been found.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 10 03 10

I/O Address 1020 DCE0 E400

2 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter

Connecting to a Windows NT 4.0 Server

9When prompted, click on “Next” and then click on “Other Locations” to

provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.

10 Insert the drivers diskette and set the path statement to “A:\” and click on

“OK”.

11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on

“Finish”.

12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and

click on “OK”.

13 Click “OK” to the “Network dialog box to provide computer / workgroup

names.

14 Specify your Computer Name, Workgroup, and Computer Description. (If

you do not have the required information, contact your network

administrator).

15 Click on “Close” button, and files will copy.

16 Click on the “Yes” button to finish the installation and restart your

computer.

3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter

Microsoft Windows 95 SR2.5

3 Installing the Intel EtherExpress PRO 100B-TX PCI

Ethernet Adapter

Microsoft Windows 95

SR2.5

Connecting to a Novell

NetWare 3.12 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.

• Microsoft Windows 95 SR2.5 media.

• Novell NetWare 3.12 system that supports NetBEUI, TCP/IP, NWLink

IPX/SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-

TX PCI adapter card into an PCI slot.

2Connect network cable media to the PRO 100B-TX PCI card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and

execute “A:\SETUP.EXE”.

5Select “VIEW ADAPTER SETTINGS” and verify the resource settings

listed above under the heading “Device Configuration”.

6If changes are required, save those changes and exit.

7Remove the Intel Software driver diskette and restart the system.

8When Windows 95 restarts, a message will appear to indicate that a new

hardware has been found.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 10 03 11

I/O Address 1020 DCE0 E400

3 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter

Connecting to a Novell NetWare 3.12 Server

9When prompted, click on “Next” and then click on “Other Locations” to

provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.

10 Insert the drivers diskette and set the path statement to “A:\” and click on

“OK”.

11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on

“Finish”.

12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and

click on “OK”.

13 Click “OK” to the “Network dialog box to provide computer / workgroup

names.

14 Specify your Computer Name, Workgroup, and Computer Description. (If

you do not have the required information, contact your network

administrator).

15 Click on “Close” button, and files will copy.

16 Click on the “Yes” button to finish the installation and restart your

computer.

4 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter

Microsoft Windows 95 SR2.5

4 Installing the Intel EtherExpress PRO 100B-TX PCI

Ethernet Adapter

Microsoft Windows 95

SR2.5

Connecting to a Novell

NetWare 4.11 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 100B-TX PCI Ethernet card and drivers disk.

• Microsoft Windows 95 SR2.5 media.

• Novell NetWare 4.11 system that supports NetBEUI, TCP/IP, NWLink

IPX/SPX, and NWLink NetBIOS transfer protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 100B-

TX PCI adapter card into an PCI slot.

2Connect network cable media to the PRO 100B-TX PCI card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and

execute “A:\SETUP.EXE”.

5Select “VIEW ADAPTER SETTINGS” and verify the resource settings

listed above under the heading “Device Configuration”.

6If changes are required, save those changes and exit.

7Remove the Intel Software driver diskette and restart the system.

8When Windows 95 restarts, a message will appear to indicate that a new

hardware has been found.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 10 03 10

I/O Address 1020 DCE0 E400

4 Installing the Intel EtherExpress PRO 100B-TX PCI Ethernet Adapter

Connecting to a Novell NetWare 4.11 Server

9When prompted, click on “Next” and then click on “Other Locations” to

provide the drivers for the Intel EtherExpress PRO 100B-TX PCI 10/100.

10 Insert the drivers diskette and set the path statement to “A:\” and click on

“OK”.

11 With the “Intel 82557C-Based Ethernet PCI (10/100)” listed, click on

“Finish”.

12 When asked to supply the driver “net82557.INF”, set the path to “A:\” and

click on “OK”.

13 Click “OK” to the “Network dialog box to provide computer / workgroup

names.

14 Specify your Computer Name, Workgroup, and Computer Description. (If

you do not have the required information, contact your network

administrator).

15 Click on “Close” button, and files will copy.

16 Click on the “Yes” button to finish the installation and restart your

computer.

Andere HP Netzwerkkarte Handbücher

HP Console Management Controller Bedienungsanleitung

HP Q6275A Bedienungsanleitung

HP Vectra VE5 4 Bedienungsanleitung

HP 3C905B-TX Bedienungsanleitung

HP hn210w Bedienungsanleitung

HP AB290A Bedienungsanleitung

HP StorageWorks AB232A Bedienungsanleitung

HP External Devices Bedienungsanleitung

HP StorageWorks FC2143 Gebrauchsanweisung

HP A7011A Bedienungsanleitung

HP 3C509B-TP Bedienungsanleitung

HP hn210p Bedienungsanleitung

HP 517 Bedienungsanleitung

HP AD331A Bedienungsanleitung

HP NC510C Bedienungsanleitung

HP HP-UX SNAplus2 Bedienungsanleitung

HP D7522A 10/100 3Com 3C905C-TX Bedienungsanleitung

HP NC373F Bedienungsanleitung

HP Memory Modules Bedienungsanleitung

HP Broadband Service Analyzer Bedienungsanleitung

HP Ethernet USB Network Adapter hn210e Bedienungsanleitung

HP Pro100B Bedienungsanleitung

HP DA-10852 Bedienungsanleitung

HP Rp7410 - Server - 0 MB RAM Installations- und Betriebshandbuch

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung

Gigafast

Gigafast EE101-AEX Bedienungsanleitung