HP ProCurve MSM317 Bedienungsanleitung
MSM317 Access Device Installation Guide
This guide describes how to physically install the MSM317 in an electrical outlet box
and make all necessary power and network connections. This guide assumes that
before installing the MSM317, all configuration issues have been addressed as
described in the MSM317 Access Device Installation and Getting Started Guide
available at: www.procurve.com/manuals.
The MSM317 Access Device is a
wireless/wired end-point solution with
an integrated four-port (plus uplink)
managed Ethernet switch that can be
installed in a standard NEMA-WD6
(US) or BS 4662 (International)
electrical outlet box.
It provides a complete connectivity
solution for hospitality or multiple
dwelling unit applications, supporting
a variety of IP-based in-room
applications over a single wire. (J9422A) (J9423A)
Package contents
• MSM317 body • Two mounting screws
• Two faceplates (NEMA-WD6 and BS 4662) •Thisguide
• Two trim panels (NEMA-WD6 and BS 4662)
Professional installation required
Professional installation of the MSM317 is required for proper RF operation and compliance.
Please consult with a professional installer who is trained in RF installation and knowledgeable
about local regulations (including building and wiring codes) to ensure that the MSM317 is
operating in accordance with channel, power, indoor/outdoor restrictions and license
requirements for the intended country of operation.
Safety information
Take note of the following safety information during installation of the MSM317:
• Communications wires and cables which are installed in building locations shall be listed CM
type in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular
Section 800.179 (Communications Wires and Cables).
• Conductors and equipment shall be installed in accordance with ANSI/NFPA 70, the National
Electrical Code (NEC), in particular Section 725.133 (Installation of Conductors and
Equipment in Cables, Compartments, Cable Trays, Enclosures, Manholes, Outlet Boxes,
Device Boxes, and Raceways for Class 2 and Class 3 Circuits).
• Wiring methods and materials shall be in accordance with NFPA 70, the National Electrical
Code (NEC), in particular Section 725.130.
• Handle exposed metal components of the network with caution.
NEMA-WD6 Version BS 4662 Version
2 MSM317 Access Device Installation Guide
• This product does not have a power switch. It is powered-on when the Uplink port is plugged
into a PoE power source.
• This product and all interconnected equipment must be installed indoors within the same
building, including all associated network connections as described by Environment A of the
IEEE 802.3af standard.
• It is normal for the rear metal cover of the MSM317 to get hot during operation. The cover is a
heat sink and is used to dissipate the heat generated by the MSM317.
MSM317 connectors and status lights
MSM317 components
Faceplate Trim Panel
MSM317 Body
NEMA-WD6 Version
BS 4662 Version
3MSM317 Access Device Installation Guide
Installation procedure
A. Attach the faceplate
Place the appropriate faceplate (NEMA-WD6 for US or BS 4662 for international) over the
front of the MSM317 body and press firmly to snap it into place.
B. Prepare the electrical outlet box
The MSM317 requires a single-gang electrical outlet box mounted in a wall cavity. The US version
requires a box conforming to NEMA-WD6, with a minimum depth of 1.4 inches. The International
version requires a box conforming to BS 4662, with a minimum depth of 35mm.
1. Install an appropriate electrical outlet box. Or if using an existing electrical outlet box,
disconnect and remove any existing equipment.
2. Run the required cables through the bottom of the electrical outlet box allowing sufficient
slack for the cables to reach the not-yet installed MSM317.
C. Connect the cables
1. Connect an Ethernet cable to the
Uplink port either via the RJ-45
connector or the Punch-down
block. Do not connect to both.
(See Punch-down block wiring on
page 4 for wiring details.)
2. If required, connect the cable
providing support for pass-through
devices to the Pass Through port.
D. Mount the MSM317
1. Attach the MSM317 to the
electrical outlet box using the
supplied mounting screws.
2. Place the appropriate trim panel
(US or International) over the front
of the MSM317 body and press
firmly to snap it into place.
E. Configure the MSM317
For details, see the MSM317 Access
Device Installation and Getting
Started Guide.
4 MSM317 Access Device Installation Guide
Faceplate and trim panel removal
To remove the faceplate, slightly push in two tabs on one side of the MSM317 body with a small
screwdriver. To remove the trim panel, pry off the trim panel with a small flat screwdriver.
Press here
to remove
the faceplate. Use a screwdriver to
pry off trim panel here.
(BS 4662 version shown.)
Punch-down block wiring
When terminating a cable run with the Punch-down block, always use solid conductor cables.
Stranded cables may not make good connections. To ensure good connections, install cables
into the individual Punch-down connectors using a 110-style tool.
CAUTION: Do not connect both the Punch-down block and the Uplink port to a network. Only
one connection can be used at a time.
© Copyright 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. 5900-0236
Andere Handbücher für ProCurve MSM317
3
Inhaltsverzeichnis
Andere HP Netzwerk-Router Handbücher
HP
HP FlexFabric 5930 Series Bedienungsanleitung
HP
HP StorageWorks SR2122-2 Anleitung zur Verwendung
HP
HP J4093A Bedienungsanleitung
HP
HP 5920 Bedienungsanleitung
HP
HP FlexNetwork MSR Series Installationshandbuch
HP
HP HP ProCurve Series 6600 Bedienungsanleitung
HP
HP FlexNetwork MSR 954 Bedienungsanleitung
HP
HP 7000dl Series Bedienungsanleitung
HP
HP StorageWorks M2402 Bedienungsanleitung
HP
HP MSR SERIES Bedienungsanleitung
HP
HP A6602 Bedienungsanleitung
HP
HP Deskjet 812c Bedienungsanleitung
HP
HP 5920 Bedienungsanleitung
HP
HP MSR2000 Series Bedienungsanleitung
HP
HP MSR930 3G Bedienungsanleitung
HP
HP A-MSR900 Series Bedienungsanleitung
HP
HP MSR ASM Bedienungsanleitung
HP
HP ISCSI SR2122 Bedienungsanleitung
HP
HP ProCurve 7102 Bedienungsanleitung
HP
HP Series 200 Benutzerhandbuch
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise