HP StorageWorks 2312 Leitfaden
HP StorageWorks
2312/2324 Modular Smart
Array DC power supply
replacement instructions
© Copyright 2008 Hewlett-Packard Development Company, L.P.
First edition: November, 2008
The information in this document is subject to change without
notice.
Printed in China
www.hp.com
500919-001
About this document
This document details procedures for replacing a failed DC power
supply in an HP StorageWorks 2000 Family Modular Smart Array.
Before you begin
CAUTION:
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection:
•Keep the replacement component in the ESD bag until needed
•Wear an ESD wrist strap grounded to an unpainted surface
of the chassis.
•If an ESD wrist strap is unavailable, touch an unpainted surface
of the chassis before handling the component.
•Never touch connector pins.
Verifying component failure
Check the DC Voltage/Fan Fault/Service Required (bottom) LED:
•Amber = Fault condition
Disconnecting a DC power cable
IMPORTANT:
Use only the DC power cables provided with your product.
1. Verify that the main breaker to the rack is shut off prior to
disconnecting any DC connections.
2. Verify that all enclosure power switches are off.
3. Loosen the cable-locking screws attaching the D-shell connector to
the power supply.
4. Disconnect the power cable from the power supply.
5. Turn on the main breaker to the rack.
Removing a power supply
1. Turn the thumbscrew until it is disengaged from the module.
2. Rotate the latch downward to disconnect the internal connector,
and slide the module out.
Page 1
Installing a DC power supply
1. Slide the module into the slot as far as it will go.
2. Press the latch upward to engage the module; turn the thumbscrews
finger-tight
3. Connect a DC power cable to each power supply using the
D-shell connector. Use the up arrow on the shell to ensure proper
positioning before tightening.
4. Tighten the screws at the top and bottom of the shell with a torque
between 1.7 N-m (15 lb-in) and 2.3 N-m (20 lb-in) to attach the
cable securely to the DC power sources.
5. Turn on the main breaker to the rack.
6. Turn on the enclosure power switches.
Verifying component replacement
After replacing the module, check that the Input Power Good LED is on
and the DC Voltage/Fan Fault/Service Required (bottom) LED is off.
Additional information
See the MSA2000 web site: http://www.hp.com/go/msa2000.
Page 2
Dieses Handbuch passt für folgende Modelle
1
Andere HP Stromversorgung Handbücher
HP
HP 11900 Bedienungsanleitung
HP
HP 711A Bedienungsanleitung
HP
HP 6205C Service-Handbuch
HP
HP D7171A - NetServer - LPr Bedienungsanleitung
HP
HP Entry-Level Gebrauchsanweisung
HP
HP 6259B Service-Handbuch
HP
HP StorageWorks SN6000 Bedienungsanleitung
HP
HP SCR-1P Series Service-Handbuch
HP
HP PSR750-A Bedienungsanleitung
HP
HP A7502 Bedienungsanleitung
HP
HP StorageWorks 7110 - Virtual Array Bedienungsanleitung
HP
HP 710B Stücklistenhandbuch
HP
HP 721A Betriebsanleitung
HP
HP 6236B Service-Handbuch
HP
HP E3610A Bedienungsanleitung
HP
HP 6104A Service-Handbuch
HP
HP E3620A Bedienungsanleitung
HP
HP 712B Betriebsanleitung
HP
HP 6200B Service-Handbuch
HP
HP BENCH Series Service-Handbuch
