HP StorageWorks SN6000 Bedienungsanleitung
Page 1
*5697-1309*
HP Part Number: 5697-1309
Published: November 2011
Edition: 2
Overview
Congratulations on your purchase of the HP SN6000
Fibre Channel Switch power supply. This document
provides procedures for replacing SN6000 Fibre
Channel Switch power supply models SBPSFANBF,
SBPSFANFB, SBPSFAN2BF, and SBPSFAN2F. These
instructions are also available in the HP SN6000
Fibre Channel Switch Installation and Reference
Guide.
Supported switches
This power supply is for the HP SN6000 Dual Power
Supply Fibre Channel Switch.
Related documentation
For the latest documentation for the HP SN6000 Fibre
Channel Switch, see the HP website
http://www.hp.com/go/sn6000.
Before you begin
CAUTION:
•Both power supplies must have the same
air flow direction to prevent the switch
from overheating.
•To avoid overheating, do not operate the
switch with one power supply any longer
than necessary.
•This is a Class A product. In a domestic
environment, this product may cause
radio interference, in which case, the user
may be required to take adequate
measures.
Collect the required items
Required tools:
•Cross-head screwdriver, medium
© Copyright 2011 Hewlett-Packard Development Company, L.P.
Printed in the U.S.
HP SN6000
Fibre Channel Switch
Power Supply Quick Start
Installation Instructions
Page 2
Verify the contents
Check the contents of the SN6000 Fibre Channel
Switch power supply carton. The carton contains one
power supply.
Preparation
The power supplies are hot pluggable and
interchangeable. When removing or replacing a
power supply on an operating switch, be sure that the
Heartbeat LED is flashing once per second. This
indicates that the switch will continue operating
normally while the power supply is being removed or
replaced.
Figure 1 Observing the Heartbeat LED
Removing the failed power supply
1. Unplug the power cord from the power supply.
2. Using a cross-head screwdriver, loosen the two
knurled fasteners.
3. Grasp the power supply handle and pull firmly
to disengage the modular connector.
4. Remove the power supply from the bay.
Figure 2 Removing the failed power supply
Installing the new power supply
1. Confirm that the new power supply air flow
direction is compatible with the old power
supply. The air flow direction is noted on the
part number label.
2. With the AC receptacle on the right, slide the
power supply into the bay until it is firmly
seated.
3. Secure the knurled fasteners by hand.
4. Plug the power cord into the AC receptacle and
confirm that the air flow direction is correct.
Figure 3 Installing the new power supply
1 Heartbeat LED (green)
1 Knurled fastener 2 Handle
1
1
2
1
1 Part number label 2 AC receptacle
1
2
Andere Handbücher für StorageWorks SN6000
7
Inhaltsverzeichnis
Andere HP Stromversorgung Handbücher
HP
HP 6960A Service-Handbuch
HP
HP StorageWorks 2300 - Disk System Kurzanleitung
HP
HP E3631A Leitfaden
HP
HP 66312A Betriebsanleitung
HP
HP 6236B Service-Handbuch
HP
HP 711A Bedienungsanleitung
HP
HP J2962A Installations- und Betriebsanleitung
HP
HP E3633A Bedienungsanleitung
HP
HP 640 RPS/EPS Bedienungsanleitung
HP
HP SCR-1P Series Service-Handbuch
HP
HP StorageWorks 1000 - Modular Smart Array Betriebsanleitung
HP
HP J9405B Montageanleitung
HP
HP 6235A Service-Handbuch
HP
HP 711A Service-Handbuch
HP
HP 6205C Service-Handbuch
HP
HP 6200B Service-Handbuch
HP
HP 6034A Bedienungsanleitung
HP
HP 6434B Service-Handbuch
HP
HP Lab Series Gebrauchsanweisung
HP
HP 6220B Service-Handbuch
