HP Designjet 8000s Take-Up Reel Kit Bedienungsanleitung

HP Designjet 8000s Take-Up Reel Kit

Installation Guide

Legal notices

The information contained in this document

is subject to change without notice.

Hewlett-Packard makes no warranty of any

kind with regard to this material, including,

but not limited to, the implied warranties of

merchantability and fitness for a particular

purpose.

Hewlett-Packard shall not be liable for errors

contained herein or for incidental or

consequential damages in connection with

the furnishing, performance, or use of this

material.

No part of this document may be

photocopied or translated to another

language without the prior written consent of

Hewlett-Packard Company.

Installing the take-up reel

This Installation Guide contains information necessary to install and set up the HP Designjet 8000s

Take-up Reel Kit (Model Q6681A). For information about using the take-up reel, refer to the HP Designjet

8000s Printer User's Guide.

Two people will be required to install the take-up reel. Make sure there is enough space to access the

front and the rear of the printer. All mechanical installation takes place from the front of the printer and

electrical connections are made at the rear.

The tool you need to install the take-up reel is included in the box, and consists of a cross-head (Phillips)

screwdriver.

To install the take-up reel:

1. Open the box and remove all parts.

1. Left end plate. 4. Take-up reel assembly.

2. Right end plate. 5. Motor cable.

3. Media sensor assembly. 6. Tension bar.

ENWW 1

Installing the take-up reel

2. Install the right end plate as follows:

a. Insert the lip (1) on the right end plate into the slot (2) on the right leg on the printer stand.

b. Install three screws (1) to fix the right end plate to the right printer leg stand.

3. Install the left end plate as follows:

a. Insert the lip on the left end plate into the slot on the left leg on the printer stand.

b. Install three washers (1) and screws (2) to fix the left end plate to the left printer leg stand.

NOTE The left end plate allows for vertical movement so that the take-up reel height

can be adjusted even with the screws fully inserted.

2 Installing the take-up reel ENWW

Installing the take-up reel

4. Install the take-up reel assembly as follows:

a. Place the take-up reel assembly (3) onto the printer stand crossbar.

b. Rest the ends of the support bar (2) on the ledges (1) on each end plate.

5. Install the holding bracket (1) at each end to secure the support bar as follows:

ENWW 3

Installing the take-up reel

a. Install the bottom of the holding bracket into the slot (2) on the end plate.

b. Install one screw (1) into each holding bracket to secure it to the end plate.

6. Turn the take-up reel stop screws (1) anti-clockwise to release the right and left assemblies.

4 Installing the take-up reel ENWW

Installing the take-up reel

7. Slide the left (1) and right (2) take-up reel assemblies to the right and left ends of the support bar.

Remove the assembly packaging (3).

8. Turn the take-up reel stop screws (1) clockwise to lock the right and left take-up reel assemblies.

9. Install one screw (2) to secure the take-up reel media sensor assembly (1) to the right stand.

10. At the rear of the printer, insert the following connectors into the rear of the right take-up reel

assembly and secure them with the cable clip (3):

a. Insert the media sensor connector (1).

b. Insert the take-up reel motor cable connector (2).

ENWW 5

Installing the take-up reel

11. Insert the connector on the other end of the motor cable (1) into the rear of the printer.

12. Secure the motor cable with the three cable clips (1) on the rear of the printer.

6 Installing the take-up reel ENWW

Installing the take-up reel

13. Load the tension bar (1) into the take-up reel.

The height of the take-up reel may require adjustment as it must be horizontally aligned to the media

output from the printer. Refer to the next section to verify alignment of the take-up reel height.

Take-up reel horizontal alignment

The height of the take-up reel may require adjustment as it must be horizontally aligned to the media

output from the printer. To verify alignment of the take-up reel height you need to print the take-up reel

test print.

The printer will print a line across the width of the media. Use this line to check the alignment of the right

side of the take-up reel with the left side. Use the take-up reel tension bar as the horizontal reference

for alignment.

Print the take-up reel pattern on roll media to ensure that there is sufficient length to feed the media to

the tension bar on the take-up reel.

Print the take-up reel print as follows:

1. When the "Printer Ready" message appears on the Front Panel, press the ONLINE key to take the

Printer offline.

2. Press the SHIFT key twice and select the ADJUST menu using the ◄key.

3. In the ADJUST submenu, scroll to TEST PRINTS and press the ENTER key.

4. In the TEST PRINTS menu scroll to the TUR ADJ PRINToption and press the ENTER key.

5. Press the ENTER key to start printing the pattern.

ENWW Take-up reel horizontal alignment 7

Installing the take-up reel

The printer automatically feeds the media through the printer so that the pattern reaches the take-up

reel tension bar.

If the pattern (2) on the right and left edge of the media is aligned with the same groove (1) on the tension

bar, no height adjustment is required.

If the pattern on the left edge of the media is not aligned with the same groove as on the right edge, use

the take-up reel height screw (1) to adjust the take-up reel height up (2) or down (3).

Only the left side of the take-up reel can be adjusted up or down.

8 Installing the take-up reel ENWW

Installing the take-up reel

Andere HP Druckerzubehör Handbücher

HP HP 802.11b Printer Card C8264A#A2L... Bedienungsanleitung

HP 2500 - Color LaserJet Laser Printer Bedienungsanleitung

HP C8519A - LaserJet 9000 B/W Laser Printer Bedienungsanleitung

HP 5100 - LaserJet B/W Laser Printer Bedienungsanleitung

HP PageWide XL Bedienungsanleitung

HP 5100 - LaserJet B/W Laser Printer Bedienungsanleitung

HP Color LaserJet 4610n Series Bedienungsanleitung

HP LaserJet M5025 MFP Bedienungsanleitung

HP Ink Tank 110 series Bedienungsanleitung

HP LaserJet 4MV Series Bedienungsanleitung

HP 4600 - Color LaserJet Laser Printer Bedienungsanleitung

HP LaserJet Enterprise M4555 Bedienungsanleitung

HP Laserjet,Color Laserjet 2550L Bedienungsanleitung

HP B5L53A Bedienungsanleitung

HP 51641A Bedienungsanleitung

HP Smart Tank Wireless 450 Series Bedienungsanleitung

HP Laserjet,Color Laserjet 4350 Bedienungsanleitung

HP C4196A Bedienungsanleitung

HP Designjet T1500 series Bedienungsanleitung

HP CF410A Bedienungsanleitung

HP SDCAB-0603 Bedienungsanleitung

HP c8531 a Bedienungsanleitung

HP CP4525N COLOR LASERJET ENTERPRISE Bedienungsanleitung

HP C6615D Bedienungsanleitung

Beliebte Druckerzubehör Handbücher anderer Marken

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

REA

REA JET HR pro 2K Bedienungsanleitung

oliser

oliser MS 45 Bedienungsanleitung

Roland

Roland DU2-64 Anleitungen und Rezepte

Xerox

Xerox EFI EXP6000 Bedienungsanleitung

Canon

Canon Finisher-T1 Bedienungsanleitung

Sharp

Sharp FO-1MK Bedienungsanleitung

Epson

Epson T6248 Betriebsanleitung

Canon

Canon TonerRobot EP-27 Bedienungsanleitung

GBC

GBC 16 Series Bedienungsanleitung

Canon

Canon INNER 2-WAY TRAY-E1 Bedienungs- und Wartungshandbuch

Develop

Develop SD-509 Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Triumph Adler

Triumph Adler DF-710 Handbuch

Ricoh

Ricoh LCIT RT5100 Kurzanleitung

Citizen

Citizen CBM-202PC Series Bedienungsanleitung

Canon

Canon Color imageCLASS MF8170c Bedienungsanleitung

Codonics

Codonics Virtua 1VCX-LR833 Referenzhandbuch