HP Scitex LX820 Bedienungsanleitung

SCITEX Dual Roll Kit

User’s guide

Company, L.P.

First edition

Legal notices

The information contained herein is subject

to change without notice.

The only warranties for HP Products and

services are set forth in the express warranty

statement accompanying such products and

services. Nothing herein should be

construed as constituting an additional

warranty. HP shall not be liable for technical

or editorial errors or omissions contained

herein.

Table of contents

1 Introduction ...................................................................................................................... 1

Purpose .................................................................................................................................. 1

Main components .................................................................................................................... 1

Requirements ........................................................................................................................... 1

2 Use of the dual-roll spindle ............................................................................................... 2

Load rolls onto the spindle ......................................................................................................... 2

Load rolls into the printer ........................................................................................................... 5

3 Troubleshooting .............................................................................................................. 10

4 Specifications .................................................................................................................. 11

ENWW iii

iv ENWW

1 Introduction

Purpose

The purpose of this document is to describe how to install, use and troubleshoot the Dual Roll used in

the following Printers:

●HP Scitex LX800 Printer (126-in)

●HP Scitex LX820 Printer (126-in)

●HP Scitex LX850 Printer (126-in)

●HP Scitex LX600 Printer (104-in)

●HP Designjet L65500 Printer (104-in)

For information about using these printers, refer to the corresponding User Guide or Maintenance and

Troubleshooting Guide.

Main components

The Dual Roll Kit includes the following components.

●Two dual-roll spindles, each including one differential hub

●One pair of substrate edge holders

●One Allen key

Requirements

Before using the Dual Roll Kit with an HP LX Designjet printer, you must check that the printer's firmware

and HP Internal Print Server software are up to date.

Go to http://www.hp.com/ and click Support & Drivers > Download drivers and software

(and firmware), enter the product name, click the name of your operating system, and download the

latest firmware and the latest Internal Print Server, if you do not already have them.

ENWW Purpose 1

Introduction

2 Use of the dual-roll spindle

Load rolls onto the spindle

The dual-roll spindle is marked to assist you in positioning the differential hub.

NOTE: The spindle marked Ais for the dimensions of the 126-in spindle. The spindle marked Bis for

the dimensions of the 104-in spindle.

Loading the dual-roll spindles

1. Ensure that the differential hubs on the input and output spindles are aligned with each other.

2 Chapter 2 Use of the dual-roll spindle ENWW

Dual-roll spindle

2. When both differential hubs are correctly positioned, use the Allen key to tighten the screws and

secure them in place. If a differential hub is loose, the substrate could become skewed during

printing.

TIP: You should tighten the screw until the washer touches the bolt. If you can still see the yellow

spring, tighten the screw further.

3. At each end of the spindle, unscrew and remove the outer parts of the hub, using the Allen key.

4. Unscrew and remove the inner part of each hub.

ENWW Load rolls onto the spindle 3

Dual-roll spindle

5. Insert the first roll on the spindle.

6. Replace the hub, and secure it with the Allen key.

7. Insert the second roll on the spindle.

8. Replace the hub, and secure it with the Allen key.

9. Ensure that the end of the right-hand roll is located within the maximum allowed distance from the

right-hand end of the spindle: it should be between the gear and the dashed line.

10. Ensure that the roll core fits tightly on the hub.

4 Chapter 2 Use of the dual-roll spindle ENWW

Dual-roll spindle

11. Ensure that the roll core fits tightly on the differential hub.

12. Load the spindle at the rear of the printer, and secure the spindle latches.

13. Use the same process to load the output spindle at the front of the printer, but load the spindle with

two empty cores to receive the printed substrate.

Load rolls into the printer

The two substrate rolls are mounted on the rear dual-roll spindle and will be collected on the front dual-

roll spindle. The substrate goes from the rear spindle over the main roller, over the platen, over the front

roller and then to the front spindle.

NOTE: You can load substrate with the printed face inwards or outwards on the spindle, in which

case the spindle will turn in the opposite direction. The printer asks you for the winding direction if it

cannot detect it automatically.

Before loading two rolls into the printer, you must have both rolls loaded on the rear dual-roll spindle

and two empty cores loaded on the front dual-roll spindle. See Load rolls onto the spindle on page 2.

1. Tell the printer that you are going to begin loading for dual-roll printing.

2. Remove the substrate edge holders in the print platen, or move them aside, so that they do not get

in the way while loading the substrate.

CAUTION: Loading the substrate on top of the edge holders could severely damage the

printheads and carriage.

3. Lift the substrate pressure handles at the rear of the printer.

ENWW Load rolls into the printer 5

Dual-roll spindle

4. If you need to raise the carriage beam, go to the front panel and select the Substrate menu ,

then Substrate management, and press OK. Select Carriage beam position > Move to

highest position. This process takes about 2 minutes to complete.

The printer raises the carriage beam, making it easy to insert the substrate. This process takes

about 2 minutes to complete. During this period, you can load the input and output rolls.

NOTE: While the carriage beam is rising, you can stop it by pressing the Cancel key.

5. You may find it helpful to lock the differentials on the input and output spindles while loading.

6. Bring the new rolls on their spindle to the rear of the printer, with the geared end of the spindle on

the left.

7. If the two rolls are of unequal lengths, the longer roll should be on the right as seen from the front

of the printer; on the left as seen from the rear.

NOTE: When the shorter roll comes to an end, you should lock the differential hub if you intend

to continue printing on the longer roll.

8. Rest the ends of the spindle on the platforms provided at the rear of the printer; plastic pads are

provided to absorb the impacts.

6 Chapter 2 Use of the dual-roll spindle ENWW

Dual-roll spindle

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Druckerzubehör Handbücher

HP 2500 - Color LaserJet Laser Printer Bedienungsanleitung

HP LaserJet M4345 - Multifunction Printer Bedienungsanleitung

HP LaserJet M5025 MFP Bedienungsanleitung

HP Officejet 100 Bedienungsanleitung

HP C8519A - LaserJet 9000 B/W Laser Printer Bedienungsanleitung

HP 51641A Bedienungsanleitung

HP LaserJet P3005 Series Bedienungsanleitung

HP Laserjet,Color Laserjet 4si Bedienungsanleitung

HP CF283X Kurzanleitung

HP C8519A - LaserJet 9000 B/W Laser Printer Bedienungsanleitung

HP Deskjet 1280 Bedienungsanleitung

HP C8519A - LaserJet 9000 B/W Laser Printer Bedienungsanleitung

HP LaserJet 4200dtn Bedienungsanleitung

HP Designjet 8000s Take-Up Reel Kit Bedienungsanleitung

HP HP 802.11b Printer Card C8264A#A2L... Bedienungsanleitung

HP Smart Tank Wireless 450 series Bedienungsanleitung

HP Color LaserJet 9500 Bedienungsanleitung

HP B5L53A Bedienungsanleitung

HP Jetdirect 2800w Bedienungsanleitung

HP P Color LaserJet 5 Bedienungsanleitung

HP LaserJet LJ 5M Bedienungsanleitung

HP LaserJet Enterprise M4555 Bedienungsanleitung

HP CM4540 COLOR LASERJET Handbuch

HP LaserJet M4345 - Multifunction Printer Bedienungsanleitung

Beliebte Druckerzubehör Handbücher anderer Marken

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

REA

REA JET HR pro 2K Bedienungsanleitung

oliser

oliser MS 45 Bedienungsanleitung

Roland

Roland DU2-64 Anleitungen und Rezepte

Xerox

Xerox EFI EXP6000 Bedienungsanleitung

Canon

Canon Finisher-T1 Bedienungsanleitung

Sharp

Sharp FO-1MK Bedienungsanleitung

Labelmate

Labelmate PM-300 Bedienungsanleitung

Epson

Epson T6248 Betriebsanleitung

Epson

Epson OT-BZ20 Bedienungsanleitung

Canon

Canon TonerRobot EP-27 Bedienungsanleitung

Ricoh

Ricoh LCIT RT5100 Kurzanleitung

GBC

GBC 16 Series Bedienungsanleitung

Canon

Canon INNER 2-WAY TRAY-E1 Bedienungs- und Wartungshandbuch

Develop

Develop SD-509 Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Triumph Adler

Triumph Adler DF-710 Handbuch

Citizen

Citizen CBM-202PC Series Bedienungsanleitung